User Manual

ManualsBrandsKlipsch ManualsAudio MonitoringS1 True Wireless In-Ear Headphones

GETTING STARTED FOR KLIPSCH S1 TRUE WIRELESS

INITIAL SET UP AND PAIRING:

1. Turn on the earphones by holding down the touch buttons (over the logo) on

both earphones for 3 seconds.

2. Once they are turned on you will hear a prompt indicating that the Left and the

Right Channels have been connected to each other.

3. Now it is time to pair them to your phone. Open up the Bluetooth connection

menu of your smartphone or tablet. Connect to “S1” or “Klipsch S1 True

Wireless”. If it does not connect right away wait 5 seconds and try again.

4. Once connected the earphones will recognize your device and will

automatically connect to it every time they are powered on in the future.

AUTO POWER ON/OFF:

There are 2 ways to power on the earphones:

1. If they are in the charging case simply remove the earphones without touching

the touch buttons to auto power on the earphones.

2. If they are not in the charging case or the case has run of power, press the

touch buttons on both earphones for 3 seconds to power on.

There are 2 ways to power off the earphones:

1. To auto power off place the earphones back into the charging case. After 5

seconds the earphones will automatically turn off and begin the charging

process. These features may not work if the charging case has been fully

depleted of power.

2. To manually power off press and hold the touch button over the logo of the

earphone for 3-5 seconds.

CHARGING THE EARPHONES:

1. To charge the earphones simply place them into the corresponding areas of the

charging case. Make sure they are securely in the correct position.

2. Close the lid.

3. The red indicator lights will turn on to indicate that they are charging. When

charging is complete the red lights will turn off. The blue indicator lights on the

charging case show the current power level remaining in the charging case.

CHARGING THE CASE:

1. To charge the power case plug in the included micro USB cable to the rear of the

case. Then plug the other end into a power source such as a computer or a USB

wall charger.

2. Charging is complete when all 4 LED lights are solid blue.

3. This is also compatible with wireless charging.

4. Simply place the charging case with the Klipsch brand facing upward on to a

powered wireless charging pad and charging will automatically begin.

TRUE

WIRELESS

Summary of content (4 pages)

PAGE 1
GETTING STARTED FOR KLIPSCH S1 TRUE WIRELESS S1 TRUE WIRELESS INITIAL SET UP AND PAIRING: 1. T urn on the earphones by holding down the touch buttons (over the logo) on both earphones for 3 seconds. 2. Once they are turned on you will hear a prompt indicating that the Left and the Right Channels have been connected to each other. 3. Now it is time to pair them to your phone. Open up the Bluetooth connection menu of your smartphone or tablet. Connect to “S1” or “Klipsch S1 True Wireless”.
PAGE 2
GETTING STARTED FOR KLIPSCH S1 TRUE WIRELESS S1 TRUE WIRELESS TROUBLESHOOTING: Q: What do you do when the left earphone disconnects from the right earphone? A: F irst, place the left earphone back in to the charging case and then wait 3 second and remove from the charging case. The connection between the left and right earphones should automatically re-establish and connect to each other. If this does not resolve the connection then a reset is needed.
PAGE 3
GUIDE D’UTILISATION POUR KLIPSCH VÉRITABLEMENT SANS FIL S1 TRUE WIRELESS CONFIGURATION INITIALE ET JUMELAGE : 1. A llumez les écouteurs en appuyant et maintenant les boutons tactiles (logo) des deux écouteurs enfoncés pendant 3 secondes. 2. U ne fois allumés, vous entendrez un message vocal indiquant que les écouteurs Droit et Gauche sont connectés l’un à l’autre. 3. M aintenant, il est temps de les connecter à votre appareil mobile.
PAGE 4
GUIDE D’UTILISATION POUR KLIPSCH VÉRITABLEMENT SANS FIL S1 TRUE WIRELESS DÉPANNAGE : Q : Que faire lorsque l’écouteur gauche se déconnecte de l’écouteur droit ? R : T out d’abord, remettez l’écouteur gauche dans le boitier, attendez 3 secondes puis enlevez du boitier. La connexion entre les deux écouteurs devrait être rétablie automatiquement. Si cette manoeuvre ne résout pas le problème, une réinitialisation est nécessaire.