NL GB Instructions for use
These instruction shall be available on website docs.kitchenaid.
Safety instructions IMPORTANT TO BE READ AND OBSERVED cracked, do not use the appliance – risk of electric shock. WARNING: Danger of fire : Do not store items on the cooking surfaces. CAUTION: The cooking process has to be supervised. A short cooking process has to be supervised continuously. WARNING: Unattended cooking on a hob with fat or oil can be dangerous and may result in fire. NEVER try to extinguish a fire with water, but switch off the appliance and then cover flame e.g.
slide them across the hob. off all burners and any electrical heating element and isolate the appliance from the power supply; - do not touch the appliance surface; - do not use the appliance. The glass lid can break in if it is heated up. Turn off all the burners and the electric plates before closing the lid. Do not shout down lid when burner alight. WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements.
advisable to keep only the cylinder being used in the room, positioned so that it is not subject to heat produced by external sources (ovens, fireplaces, stoves, etc. ) which could raise the temperature of the cylinder above 50°C. shock. Only activate the appliance when the installation has been completed. WARNING: Modification of the appliance and its method of installation are essential in order to use the appliance safely and correctly in all the additional countries.
or to a gas cylinder in compliance with the current national regulations. Before making the connection, make sure that the appliance is compatible with the gas supply you wish to use. If it is not, follow the instructions indicated in the paragraph "Adapting to different types of gas". After connection to the gas supply, check for leaks with soapy water. Light up the burners and turn the knobs from max position 1* to minimum position 2* to check flame stability.
DISPOSAL OF PACKAGING MATERIALS Do not use extension leads, multiple sockets or adapters. The electrical components must not be accessible to the user after installation. Do not use the appliance when you are wet or barefoot. Do not operate this appliance if it has a damaged power cable or plug, if it is not working properly, or if it has been damaged or dropped.
Product description and symbols 1. 2. 3. 4. 5. 6. 7. 8. 9.
Practical advice on using the hob Important: Do not rest or drag the pan supports upside down on the hob as this could scratch it. Read the instructions to get the best out of your hob. -- Use pans with a similar diameter to the burner (see the table on this page) -- Use flat bottomed pans except with the wok support. -- Do not use excessive water when cooking foods and use the lid. -- Ensure that pans are fully supported by the pan supports and do not protude over the edges.
Hood and cabinetry clearances (mm) If a hood is to be installed above the hob, refer to the hood installation instructions to ensure the correct height above the hob. 4 1120 38 74 R 1100 +1 12 +1 50 0 36 N.B. For the semi-flush mount version the 1.5 mm milling is not necessary. Note: If the distance “A” between the wall cupboards in the kitchen is between 600mm and 730mm, the height “B” must be at least 530mm.
Installation Technical information for the installer • This appliance can be built into a 30mm to 70mm thick worktop. • If no oven is to be installed below the hob, a panel must be fitted under the hob to prevent hob damage and protect the cupboard contents. This panel must cover the whole of the underside of the hob and must be positioned so that an air gap of at least 15mm between the panel and hob underside is maintained, as a minimum, and as a maximum 150mm to the underneath of the work surface.
Electrical connection The electrical connections must comply with current legislation and be carried out by a qualified, competent person. • Information on the voltage and power absorbed are shown on the serial no. plate. • The appliance must be earthed. • When installing the appliance, we recommend that this hob is protected by a 3mm bi-polar switch. • If damaged, the power cable must be replaced with an identical type of powercable. We recommend that this operation be conducted by our After Sales Service.
Adaption to a different type of gas supply • If you are using a different kind of gas from the one indicated on the serial no. plate and the orange label on the back of the hob, you must replace the injectors; in the case of the Wok burner, adjust the primary air (see Injector table on page 11). The orange label should be removed and kept together with the manual. Use pressure regulators suitable for the gas pressures indicated on page 11.
Injectors replacement in the wok burner To replace the injectors in special burner it is necessary to: 1. Remove spreader (C), the screws (B) holding the cover cap (A) and the cap itself. 2. Unscrew the inner injector (D) with a box spanner 7 and the outer injectors (E) with a wrench 7. 3. Replace the injectors. 4. Put back the cover cap, screws and spreader. Note: make sure that after replacement the spreader (C) is inserted correctly on the burner.
Maintenance and cleaning CLEANING THE HOB PARTS • Clean glass and enameled parts only with soft cloth or sponge. • Grids, burner caps and burners can be removed to be cleaned. • Clean them by hand with warm water and non-abrasive detergent, removing any food residues and checking that none of the burner openings is clogged. • Rinse and dry. • Refit burners and burner caps correctly in the respective housings. • When replacing the grids, make sure that the panstand area is aligned with the burner.
After-Sales Service In order to receive a more complete assistance, please register your product on www.kitchenaid.eu/register. Type: XXX Mod.: XXX XXXXXXXXXXXXXXXXXXXX Made in X BEFORE CALLING THE AFTER-SALES SERVICE: 1. See if you can solve the problem by yourself with the help of the suggestions given in the TROUBLESHOOTING. 2. Switch the appliance off and back on again to see if the fault persists. IF AFTER THE ABOVE CHECKS THE FAULT STILL OCCURS, GET IN TOUCH WITH THE NEAREST AFTER-SALES SERVICE.
WHIRLPOOL EMEA S.P.A. Via Carlo Pisacane n.