KHGL 9010/B/01 Instructions for use
Product description and symbols 4 Using the burners 4 Practical advice on using the hob 5 Positioning the pan supports and Wok pan adapter 6 Installation distances and measurements (mm) 7 Injectors table 7 Warnings and suggestions 8 Safeguarding the environment 9 Installation 10 Gas connection 10 Electrical connection 11 Installation 11 Adaption to a different type of gas supply 12 Replacing the injectors 12 Regulating the minimum flow level of the gas taps 12 General cleaning
Product description and symbols 1. Central removable pan support 2. Removable side pan support 3. Auxiliary burner 4. Semi-fast burner 5. Fast burner 6. Semi-fast burner 7. Professional triple crown WOK burner 8. Auxiliary burner control button 9. Semi-fast burner control button 10. Fast burner control button 11. Semi-fast burner control button 12.
Practical advice on using the hob Read these instructions to get the best from your hob: - Use pans with a diameter suitable for the burner you are using ( see table opposite) - Only use plat bottomed pans - Use the right amount of water for cooking the food. Prevent unnecessary water loss by using the lid. - Do not use pans that protrude over the edge of the hob. Important: Do not rest and/or drag the pan supports upside down on the hob as this could scratch it.
Positioning the pan supports and Wok pan adapter To facilitate positioning of the pan supports on the hob, it is recommended to start by fitting the central pan support (1). Place the central pan support on the surface using the double crown burner and the centre knob as a reference.
Installation distances and measurements (mm) If a hood is installed above the hob, read the instructions for fitting the hood where it indicates the correct distances to be complied with. 860 0 51 6,5 R 6 1 n. mi x R a m 45 63 m in 840 0 49 +2 -0 . +20 - Injectors table Category II2L3B/P Type of gas used Type of burner Injector marking Nominal heat flow kW Nominal consumption Reduced heat flow kW Gas presssure (mbar) min. nom.
Warnings and suggestions To get the most out of your hob, please read the instructions carefully and keep them for future consultation. • These instructions are only valid in the countries whose destination symbol is shown on the serial number plate on the hob. • The packing (plastic bags, expanded polyurethane, etc) pose a potential threat to children and should be disposed of carefully.
Safeguarding the environment Packing The packing material is 100% recyclable and is labelled with the recycling symbol . Please dispose of all packing responsibly and carefully. Conformity declaration This hob was designed, built and marketed in compliance with: • the safety requirements in the “Gas” CEE Directive 90/396. • safety objectives of the “Low Voltage” Directive 2006/95/CE (wich replaces 73/23/CEE and subsequent amendments).
Installation Technical information for the installer • This appliance can be built into a 20mm to 40mm thick worktop. • If no oven is to be installed below the hob, a panel must be fitted under the hob to prevent hob damage and protect the cupboard contents. This panel must cover the whole of the underside of the hob and must be positioned so that an air gap of at least 20mm between the panel and hob underside is maintained, as a minimum, and as a maximum 150mm to the underneath of the work surface.
Electrical connection The electrical connections must comply with current legislation and be carried out by a qualified, competent person. • Information on the voltage and power absorbed are shown on the serial no. plate. • The appliance must be earthed. • When installing the appliance, we recommend that this hob is protected by a 3mm bi-polar switch. • If damaged, the power cable must be replaced with an identical type of powercable ( H05V2V2-FT90 ºC, or H05RR-F type).
Adaption to a different type of gas supply If you are using a different kind of gas from the one indicated on the serial no. plate and the orange label on the back of the hob, you must replace the injectors; in the case of the Wok burner, adjust the primary air (see Injector table on page 7). The orange label should be removed and kept together with the manual.
General cleaning & maintenance Always disconnect the hob from the electrical power supply and wait until it cools before cleaning and/or doing maintenance work. In order to keep your hob in good condition, you must keep it clean, removing any remaining food each time you use it. • Do not steam clean. • Do not use inflammable products. • Do not leave acidic or alkaline based products like vinegar, mustard, salt, sugar or lemon juice lying on the hob.
Troubleshooting guide If the hob is not working properly work through the this guide before contacting our Customer Care Centre. 2. the burner’s openings are not blocked in relation to the thermocouple. 3. the end part of the thermocouple is clean. The burner does not ignite, or the flame is unsteady? Check that: 1. the gas, or electricity supply has not been interrupted and that the control knob is turned fully on. 2. the gas supply has not run out. 3. the openings on the burner have become blocked. 4.
Whirlpool Europe S.r.l. Viale G. Borghi, 27 - 21025 Comerio (VA) Phone 0332.759111 - Fax 0332.759268 www.whirlpool.
