GB KHDF 1160 KHDS 1160 Instructions for use
Product description and symbols 4 Using the burners 4 Practical advice on using the hob 5 Positioning the pan supports and wok support 5 Hood and cabinetry clearances (mm) 6 Injectors table 6 Warnings and suggestions 7 Safeguarding the environment 8 Installation (Flush and Semi-Flush fitting) 9 Gas connection 9 Electrical connection 10 Fixing the Hob to the supporting structure. Traditionally fitted model (Semi Flush fitting) 10 Fixing the Hob to the worktop.
Product description and symbols 1. 2. 3. 4. 5. 6. 7. 8. 9. Removable pan supports Auxiliary burner Semi-fast burner Semi-fast burner Professional wok burner Auxiliary burner control knob Semi-fast burner control knob Semi-fast burner control knob Professional wok burner control knob Control Symbols Off Maximum flame Minimum flame Using the burners If the burner goes out when the control knob is released, the thermocouple did not engage. wait al least 1 minute before repeating strps 1 to 3.
Practical advice on using the hob Please read all these instructions to get the best out of your hob. • Use pans with a similar diameter to the burner(see the table). • Use flat bottomed pans except with the wok support. • Do not use excessive water when cooking and use the lid. • Ensure that pans are fully supported by the pan supports and do not protrude over the edges. You should never use: • two burners simultaneously with just one container such as a fish kettle.
Hood and cabinetry clearances (mm) If a hood is to be installed above the hob, refer to the hood installation instructions to ensure the hood is installed at the correct minimum height above the hob. Injectors table Category II2E+H3+ Type of gas used Type of burner Injector label Control Nominal primary air heat flow (X) (mm) kW Nominal Reduced heat flow kW Gas pressure (mbar) consumption BE FR min. nom. max.
Warnings and suggestions To get the most out of your hob, please read the instructions carefully and keep them for future consultation. • This appliance should be installed in compliance with standards in force and only used in well ventilated rooms. Read the instructions before installing and using this appliance. • The pre-fitted gas connector and it’s supply pressure are shown on the label attached to the bottom of the hob.
Safeguarding the environment Packing The packing material is 100% recyclable and is labelled with the recycling symbol . Please dispose of all packing responsibly and carefully. Warning • This appliance is not intended for use by persons (including children) with reduced physical, sensor or mental capabilities or lack of experience and knowledge unless they have been given initial supervision or instruction concerning use of the applaince by a person responsible for their safety.
Installation (Flush and Semi-Flush fitting) Technical information for the installer • Warning: this is a heavy products which requires the installation to be carried out by two people. • When installing the hob it is advisable to wear protective gloves. • This appliance can be installed on worktops with a thickness over 20 mm. • If no oven is to be installed below the hob, a panel must be fitted under the hob to prevent hob damage and protect the cupboard contents.
Electrical connection The electrical connections must comply with current legislation and be carried out by a qualified, competent person. • Information on the voltage and power absorbed are shown on the serial no. plate. • The appliance must be earthed. • When installing the appliance, we recommend that this hob is protected by a 3mm bi-polar switch. • If damaged, the power cable must be replaced with an identical type of powercable ( H05V2V2-FT90ºC, or H05RR-F type).
Fixing the Hob to the worktop. Flush fitted model Important: The following procedure shall be carried out by competent technical personnel only. The hob can be installed on different types of materials, such as masonry, metal, bare wood and heat resistant laminate coated wood (90°C). 32 0 1160 1161 1148 Before positioning the hob, apply the adhesive seal supplied on the bottom perimeter of the hob itself, where this will be in contact with the worktop (fig. 2).
Adaption to a different type of gas supply If you are using a different kind of gas from the one indicated on the serial no. plate and the orange label on the back of the hob, you must replace the injectors; in the case of the Wok burner, adjust the primary air (see Injector table on page 6). The orange label should be removed and kept together with the manual. • In order to replace the injectors, contact the Customer Care Centre on 00800-3810-4026, or a qualified electrician.
Fitting the wok burner To fit the double crown wok burner: Insert in the following order: 1. burner ring (A); 2. decorative covering ring (B); 3. external burner cap (C); 4. internal burner cap (D). Note: make sure that: 1. the locating pin for the burner ring (A) is inserted correctly in the slot on the burner unit. 2. that the locating pin on the external burner cap (C) is inserted in the slot on the burner ring (A).
General cleaning & maintenance Always disconnect the hob from the electrical power supply and wait until it cools before cleaning and/or doing maintenance work. in order to keep your hob in good condition, you must keep it clean, removing any remaining food each time you use it. Cleaning the hob surface: The stainless steel surface may become stained if it comes into contact with hard water over along period of time or with extremely strong cleaning products.
Troubleshooting guide If the hob is not working properly, work through this guide before contacting our Customer Care Centre. The flame doesn’t stay on? Check that: 1. The button was pushed in properly when turning on the burner for the time required to activate the safety thermocouple. 2. The burner’s openings are not blocked near, or around the thermocouple. 3. The end part of the thermocouple is clean. The burner does not ignite, or the flame is unsteady? Check that: 1.
Whirlpool Europe S.r.l. Viale G. Borghi, 27 - 21025 Comerio (VA) Phone 0332.759111 - Fax 0332.759268 www.whirlpool.
