Instructions for use
These instruction shall be available on website docs.kitchenaid.
Important instructions for safety YOUR SAFETY AND THAT OF OTHERS IS HIGHLY IMPORTANT. This manual and the appliance itself provide important safety warnings, to be read and observed at all times. • This is the attention symbol, pertaining to safety, which alerts users to potential risks to themselves and others. All safety warnings are preceded by the attention symbol and the following terms: • DANGER: • indicates a hazardous situation which, if not avoided, will cause serious injury.
• Wear work gloves for all installation and maintenance operations. • The product is not suitable for outdoor use. • When the hob is in use, accessible parts of the hood may become hot. • Never flame cook food (flambé) under the appliance. Using free flames might cause fire. • Do not leave frying pans unattended when frying, as the frying oil may catch fire. Scrapping of household appliances • This appliance is manufactured with recyclable or reusable materials.
Installation After unpacking the appliance, check for any damage caused during transport. In case of problems, contact the dealer or the After-Sales Service. To avoid any damage, it is advisable to only remove the appliance from the polystyrene base just before installation. This information may be found on the inside of the hood, under the grease filter. Power cable replacement (type H05 VV-F 3 x 0.75 mm²) must be carried out by a qualified electrician. Contact an authorized service centre.
Troubleshooting guide The hood does not work Make sure: • There is not a power failure. • A speed has actually been selected. • The front panel is correctly hooked. • The 9-pin connection is properly inserted. (Figure 1) • The red reset button on the electrical system box is pressed. (Figure 2) • In the 9-pin connection, make sure the wires are properly inserted in the connector. (When connecting, pressing too hard could bend the contacts).
After-Sales Service Before calling the After-Sales Service: 1. See if you can solve the problem yourself with the help of the suggestions given in the "Troubleshooting guide". 2. Switch the appliance off and back on again it to see if the fault persists. • Your full address; • Your telephone number. If any repairs are required, please contact an authorised After-sales Service (to guarantee that original spare parts will be used and repairs carried out correctly).
Maintenance WARNING • Use protective gloves. • Disconnect the appliance from the power supply. IMPORTANT: After carrying out hood or filter cleaning, refit the front panel and filters, checking correct installation and hooking, otherwise the hood will not switch on. GREASE FILTER Its purpose is to retain the particles of grease produced by cooking.
Material supplied Remove all the components from the packets. Check that all the components are included. (Figure 8) • Hood assembled with extraction unit, neon and grease filters installed • 2 Carbon filters • Instructions for assembly and use • Metal box containing the electronic components. • 2 Brackets • 2 Screws Ø 3,5 x 9,5 • 4 Screws Ø M4 x 10 • 2 Washers Fig.
Installation - preliminary assembly instructions The hood is designed for installation and use in "Extractor Version" with extraction to the outside or in "Filter Version" with internal recirculation. Install the hood away from very dirty areas, windows, doors and heat sources. IMPORTANT: Before connecting the air outlet flexible tube, make sure the extraction unit non-return valves are free to rotate (Figure 9). Fig.
Installation dimensions The hood must be installed in a cabinet having the characteristics indicated in the figure (Figure 12). IMPORTANT: The hood is designed and approved for use exclusively with KitchenAid gas, electric, vitroceramic, induction hobs. For gas hobs, the total max. power is 16.2 kW. If the hood is used with gas hobs, the downdraft hood must be installed exclusively with external extraction (extractor version) and the burners must be equipped with safety valves.
Installation - assembly instructions The instructions given below in numerical order refer to the drawings in the "assembly instructions" manual, containing the respective numbering. 1. Make a 150 mm diameter hole in the cabinet for the air outlet ducting. IMPORTANT: Locate the best position according to the particular conformation. 2. Make a 842x100 mm rectangular hole behind the hob, to enable insertion of the hood.
Description and use of hood (Figure 13) 1. Control panel 2. Front panel 3. Grease filters 4. Carbon filters (Filter Version only) 5. Lighting Fig. 13 CONTROL PANEL (Figure 14) The hood has a "TOUCH" device for control of lights and speed. For correct use, carefully read the instructions below. • Button T1: Delays hood switch-off, timing the set speed for a few minutes. With this function, the hood switches off at the end of the time.
• Button T5: Opens (lifts) and closes (lowers) the extraction panel. With the hood off and panel closed, button T5 firstly opens the extraction panel and then sets the hood to extraction speed (power) 1. With the hood on (at any speed) and panel open, button T5 firstly switches the hood off (also switching off the lights, if on) and then closes the extraction panel. IMPORTANT: Use the highest speed setting for particularly concentrated steam and fumes.
n Printed in Italy 07/17 400011121862 GB