Instructions for use
Precautions and general recommendations 4 Parts of the dishwasher 5 Options and display description 6 Quick reference guide 7 First time use 8 Daily check 9 Daily use 11 How to load the racks 12 Maintenance and care 15 What to do if...
Precautions and general recommendations 1. Packing The packaging materials are 100% recyclable and marked with the recycling symbol . weight of the loaded rack when pulled out. Do not rest objects on the open door or sit or stand on it. - Sharp items that might cause injury (e.g. knives), must be placed in the cutlery basket with the sharp end facing downwards. Long-handled utensils must be arranged horizontally in the upper rack, with the sharp end facing away from the front of the appliance.
electrical and electronic appliances. Disposal must be carried out in accordance with local environmental regulations for waste disposal. For further information on the treatment, recovery and recycling of this appliance, contact your competent local authority, the collection service for household waste or the shop where you purchased the appliance. requirements of EC Directives: 2006/95/CE, 89/336/CE, 93/68/CE and 2002/95/CE (RoHS Directive). Loading Capacity: 13 place settings.
Options and display description Before using the appliance for the first time carefully read this quick reference guide and the assembly instructions! Wash time display Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates the time remaining until program start (h.00) below 1h (0:min). If “Fx Ey” messages appears on the display, see page 16 - chapter “What to do if...”.
Quick reference guide Table of programs Consumption Detergent Drying Phase Available options Loading instructions 40-70°C Delay Recommended program for routine washes, with dried-on food (e.g. EN 50242). X 7-14 Programs Litres kWh Minutes1) P1 Sensor P2 Pre-Wash cold Delay Crockery to be washed later. - 4.0 0.03 14 NO P3 Fragile 40°C Delay Light soiling, for example glasses and cups. X 10.0 0.
First time use How to set water hardness in order to always assure the best cleaning results. At first time use, the salt reservoir has to be filled independently from water hardness level (see description below in step 1 “Daily check”). Water hardness should be set only before the first wash or if water hardness has been changed. - Press and hold together PROGRAM Selection and CANCEL/Off buttons for minimum 3 seconds. - The current water hardness setting will be visible on the display.
Daily check Filling the salt reservoir Dissolve limescale (not necessary if water hardness level is set to “soft”!) Once regeneration salt is added, immediately start a wash program (the “Pre-wash” program alone is not sufficient). Residual saline solution or grains of salt can lead to deep-down corrosion, irreparably damaging the stainless steel components. The guarantee is not applicable if faults are caused by such circumstances.
Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator Check the rinse aid indicator to check the level into the dispenser. Visual indicator (depending on the model) Rinse aid indicator on the control panel The indicator lamp lights up when RINSE AID NEEDS TO BE ADDED. Rinse aid indicator on the dispenser If required, open the cover B (press the dedicated button). dark: OK.
Daily use Adding detergent Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations Use only one tablet per one cycle, only placed in detergent dispenser. All types of tablets can be used, but for 2 in 1 type adding of salt is mandatory. Some type of tablets could not dissolve completely during the short programs (Fast, Fragile, Handwash); placing the tablet on the tub bottom can help dissolving and washing. Open the cover A (press the dedicated button).
How to load the racks UPPER RACK - depending on the model How to adjust upper rack height (if available). It could be useful to lift up the upper rack to have more space in lower rack or bring it down to load long stem glasses. - Grasp and take out the two lateral handles (C) (they must be on the same level) and lift up or take down the upper rack. A - Adjustable flaps (2 or 4): in horizontal position for cups / long utensils / stemmed glasses.
LOWER RACK - depending on the model E - Cutlery basket F - Grid: helps to keep the cutlery separate for better washing results. G - Vertical plate holders: they can be folded down to load pots. H - Lateral support with foldable flaps (if available): shelves can be used to hold long tools or cups onto. The lateral support can be removed: pull the support to the front of the basket and lift to remove it. Arrange crockery so that water does not collect in cavities, ensuring that the spray arms turn freely.
Select program Overview of programs The max. possible number of programs is illustrated in the chapter “Chart”. The corresponding programs for your appliance can be found on the panel. To change the program in progress: - Open the door, press the CANCEL/Off button to cancel the running program and close the door. - (Water drains for up to 1 minute then the appliance switches off). - Open the door and press any button except CANCEL/Off button to switch on the appliance. - Select a new program.
Maintenance and care Filters Check and clean if necessary Rectifying minor faults yourself... Spray arms Remove blockages/ deposits. Unscrew microfilter (1), remove it (2) and remove fine sieve (3)... Unscrew and remove upper arm... Rinse under running water... Unscrew and remove lower arm... Insert. Clean spray nozzles under running water (use toothpicks if necessary)... Screw on microfilter NOTE MARK! Insert and screw on upper and lower arms tightly.
What to do if... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. How the faults are shown on the display: Function number “F”x - blinking 0.5 sec. pause Error number “E”y - blinking The appliance... Possible causes... Solutions... ...is not working/will not start • The appliance must be switched on.
After taking the following course of action, the fault message must be reset. In the majority of cases the fault is thus eliminated. RESET: - Press the CANCEL/Off button. - Close the door. - Water drains automatically for up to 1 minute. - The appliance is now ready to be restarted. Crockery and cutlery... Possible causes... ...are not perfectly clean/have food • Too little space between dishes residues (incorrect arrangement of the concave items in the rack).
Crockery and cutlery... Possible causes... ...are not dry • Plastic containers dry badly. • • • • • Synthetic materials do not dry well; if wet at end of cycle, wipe dry. Clean dishes left in dishwasher for a • In this situation, the presence of long time after end of cycle (e.g. drops of water on dishes and on when using “Delayed start” option). the sides of the dishwasher is normal. Try releasing the door 5 minutes before removing the dishes.
Crockery and cutlery... Possible causes... Solutions... ...rust marks • Pre-wash program not used. ...other marks • Rinse aid dosage too low. ...streaks • Rinse aid dosage too high. ...suds • Unsuitable dosage of detergent/rinse aid. • Salty or acidic food residues can cause rust marks even on stainless steel cutlery. To avoid this, always use the pre-wash program if the dishes are to be washed later. • In the presence of marks, increase the rinse aid dosage (see “Adding rinse aid”).
Printed in Italy 03/12 5019 796 01501 n GB