KCDP 9050/I
Warnings 4 Safeguarding the environment 5 Instructions for installation and use 6 Extraction mode 6 Installation 7 Hood description 10 Functioning 10 Maintenance 11 After-Sales Service 13
Warnings • This appliance should not be used by children or people with limited physical or mental abilities and with no experience or knowledge of its use, unless they are supervised by someone in charge of their safety or who has taught them how to use the appliance. • Children should not play with the appliance. 1. Do not connect the appliance to the mains supply until the installation is completely finished.
Warnings Declaration of conformity This product has been designed, manufactured and marketed according to the following: - safety objectives in the “Low Voltage” Directive 73/23/EEC. - protection requirements of “EMC” Directive 89/336/EEC amended by Directive 93/68/EEC.
Instructions for installation and use This is an excessively heavy product and the movement and installation of the hood should be done by at least two or more people. Follow the instructions in this manual carefully. All responsibility is denied for problems, damage or fire to the appliance resulting in failure to comply with the instructions in this manual.
Installation The hood comes with plugs suitable for most walls/ceilings. You should however consult a qualified technician to make sure the installation is suitable for your kind of wall/ceiling. The wall/roof should be sufficiently strong to support the weight of the hood.
Installation Fig. 4 • Using a pencil, draw a line on the wall up to the ceiling that corresponds with the centre line; this will make installation easier.
Installation Fig. 6 • Attach the chimney flue support bracket G to the wall next to the ceiling, using the chimney support bracket as a template (the small slot created on the bracket must coincide with the line previously traced on the wall) mark the 2 holes with a pencil, drill the holes and insert the 2 plugs. • Fit the chimney support bracket to the wall with the 2 screws. Only Vented mode version: fit the deflector to the chimney support bracket using 4 screws.
Hood description Fig. 8 1. Control panel 2. Grease filter 3. Handle for unhooking the grease filter 4. Halogen bulbs 5. Steam deflector screen 6. Telescopic chimney 7. Air outlet (only for use with vented mode version) 8. Perimetric suction panel Functioning Turn to maximum speed when there is a lot of steam in the kitchen. We would advise you to turn the suction on 5 minutes before starting to cook and leave it running after you have finished cooking for about another 15 minutes.
Functioning Display: shows the extraction power selected and indicates when the grease filter needs changed (F) or the carbon filter (C) needs changing. It also shows the stand by function, the calibration function of the control panel (two flashing dots), the activation of the timer (a flashing dot on the right) and the remaining running time in minutes (number on the right).
Maintenance Assembly: The panel should be hooked on the back by tightening the fasteners, while the front should be secured to the specifically placed bolts on the hood surface. Warning! Always check that the panel is fitted properly. Grease filter It should be cleaned by hand once a month (or when the system indicates that the filters are finished and need changing – if the model you own offers this option), with mild cleaning products, or in the dishwasher at a low temperature and on the short cycle.
After-Sales Service Before calling Customer Care Centre: 1. See if you can solve the problem yourself with the help of the “Troubleshooting guide”. 2. Switch off the hood for a few minutes and restart it to see if the problem has cleared itself. 3. If the malfunction persists, call the Customer Care Centre Service.
Electrical connection for Great Britain and Ireland only Warning - this appliance must be earthed Fuse replacement If the mains lead of this appliance is fitted with a BS 1363A 13amp fused plug, to change a fuse in this type of plug use an A.S.T.A. approved fuse to BS 1362 type and proceed as follows: 1. Remove the fuse cover (A) and fuse (B). 2. Fit replacement 13A fuse into fuse cover. 3. Refit both into plug.
Printed in Italy 01/07 5019 718 02009 n GB