KCDP 9010/I Instructions for use
Warnings 4 Safeguarding the environment 5 Instructions for installation and use 6 Extraction Modes 6 Installation 7 Hood description 11 Functioning 11 Maintenance 12 After-Sales Service 14
Warnings • This appliance should not be used by children or people with limited physical or mental abilities and with no experience or knowledge of its use, unless they are supervised by someone in charge of their safety or who has taught them how to use the appliance. • Children should not play with the appliance. 1. Do not connect the appliance to the mains supply until the installation is completely finished.
Warnings Declaration of conformity This product has been designed, manufactured and marketed according to the following: - safety objectives of the “Low Voltage” Directive 2006/95/CE (wich replaces 73/23/CEE and subsequent amendments). - protection requirements of “EMC” Directive 89/336/EEC amended by Directive 93/68/EEC.
Instructions for installation and use This is an excessively heavy product and the movement and installation of the hood should be done by at least two or more people. Follow the instructions in this manual carefully. All responsibility is denied for problems, damage or fire to the appliance resulting in failure to comply with the instructions in this manual.
Installation The hood comes with plugs suitable for most walls/ceilings. You should however consult a qualified technician to make sure the installation is suitable for your kind of wall/ceiling. The wall/roof should be sufficiently strong to support the weight of the hood. it with some protection where you can place the hood and parts. • Disconnect the hood by turning off the mains switch in the house when connecting the electrics.
Installation Fig. 4 • Place the lower support bracket on the perforation layout aligning it with the sketched rectangle. Mark the two external holes, then drill the holes. Remove the perforation layout and insert 2 wall plugs and fix the hood support bracket with 2 5x45mm screws. Fig. 5 • Hang the hood on the lower bracket. • Adjust the distance of the hood from the wall. • Adjust the horizontal position of the hood.
Installation • The hood has two identical brackets for attaching the chimney. Attach the first bracket (G – the side with fixing holes facing upwards – see Fig. 6) to the wall next to the ceiling, using the support bracket as a template (the small slots cut in the bracket should coincide with the centre lines previously traced on the wall), mark 2 holes with a pencil, drill the holes and attach the bracket with 2 screws and plugs.
Installation • Hook the hood onto the lower bracket. • Fit the hood securely to the wall with screws • Connect the venting pipe (Venting pipe and straps are not provided and must be purchased seperately) to the connection ring found above the motor suction unit. The other end of the pipe should be attached to venting pipe leading to the outside if you are using the extractor in the vented mode.
Hood description Fig. 9 1. Control panel 2. Grease filter 3. Handle for unhooking the grease filter 4. Halogen bulbs 5. Steam deflector screen 6. Telescopic chimney 7. Air outlet (only for use with filter version) 8. Perimetric suction panel Functioning Turn to maximum speed when there is a lot of steam in the kitchen. We would advise you to turn the extraction on 5 minutes before starting to cook and leave it running after you have finished cooking for about another 15 minutes. 1.
Maintenance Always disconnect the power supply before carrying out any kind of maintenance work. Cleaning The hood should be cleaned regularly both inside and out (at least as often as you carry out maintenance on the grease filters). Use a damp cloth with mild cleaning products. Avoid using harsh products. DO NOT USE ALCOHOL! Warning: Failure to follow the cleaning instructions on the hood and the replacement and cleaning of the filters, can lead to a significant fire risk.
Maintenance Carbon filter (only in recirculation mode) Fig. 12 The Carbon filter absorbs any unpleasant smells produced when cooking. The carbon filter can be washed every two months in hot water with suitable cleaning fluids, or in the dishwasher at 65°C (when washing in the dishwasher, do a full wash without any plates inside). Shake off any excess water without damaging the filter, then place it in the oven for 10 minutes at 100°C to dry it off completely.
After-Sales Service Before calling Customer Care Centre: 1. See if you can solve the problem yourself with the help of the “Troubleshooting guide”. 2. Switch off the hood for a few minutes and restart it to see if the problem has cleared itself. 3. If the malfunction persists, call the Customer Care Centre Service.
Electrical connection for Great Britain and Ireland only Warning - this appliance must be earthed Fuse replacement If the mains lead of this appliance is fitted with a BS 1363A 13amp fused plug, to change a fuse in this type of plug use an A.S.T.A. approved fuse to BS 1362 type and proceed as follows: 1. Remove the fuse cover (A) and fuse (B). 2. Fit replacement 13A fuse into fuse cover. 3. Refit both into plug.
Printed in Italy 05/07 5019 718 02007 n GB