5KHBC412EXX • 5KHBC412BXX 5KHBC414EXX • 5KHBC414BXX 5KHBC416EXX • 5KHBC416BXX 5KHBC418EXX • 5KHBC418BXX 5KHBC420EXX • 5KHBC420BXX W10859533A_01_EN_v18.
COMMERCIAL IMMERSION BLENDER INSTRUCTIONS English TABLE OF CONTENTS COMMERCIAL IMMERSION BLENDER SAFETY Important safeguards �����������������������������������������������������������������������������������6 Electrical requirements �������������������������������������������������������������������������������8 Electrical equipment waste disposal ������������������������������������������������������������8 Electrical data for Immersion Blender and attachments ������������������������������9 PARTS AND F
COMMERCIAL CMD + SHIFT IMMERSION CLICK TO CHANGE BLENDER COPY SAFETY C IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. Misuse of appliance may result in personal injury. 2. To protect against risk of electrical shock do not put motor body, cord, or electrical plug of this Commercial Immersion Blender in water or other liquid. 3.
COMMERCIAL IMMERSION BLENDER SAFETY English 6. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Return appliance to the nearest Authorised Service Centre for examination, repair or electrical or mechanical adjustment. 7. The use of attachments not recommended or sold by the manufacturer may cause fire, electric shock, or injury. 8. Do not use outdoors. 9. Do not let cord hang over edge of table or counter. 10.
CMD + SHIFT CLICK COMMERCIAL IMMERSION TO CHANGE BLENDER COPY SAFETY C Electrical Requirements Voltage: 220-240 V Frequency: 50-60 Hz Wattage: 750 W To reduce the risk of electrical shock, this plug will fit in an outlet only one way. If it does not fit, contact a qualified electrician. Do not modify the plug in any way. Electrical Shock Hazard Plug into an earthed outlet. Do not remove earth prong. Do not use an adapter. Do not use an extension cord.
COMMERCIAL IMMERSION BLENDER SAFETY Models Immersion Blender Whisk Blending Arm 5KHBC412 5KHBC414 5KHBC418 5KHBC416 5KHBC420 KHBC110 5KHBC112 5KHBC114 5KHBC116 5KHBC118 5KHBC120 Volts/Hertz English Electrical Data for Immersion Blender and Attachments 220-240 V / 50-60 Hz Speed-lowest 9,000 rpm 550 rpm 9,000 rpm Speed-highest 18,000 rpm 900 rpm 18,000 rpm Motor horsepower for our Commercial Immersion Blender motors was measured using a dynamometer, a machine laboratories routinely use to
PARTS CMD +AND SHIFT FEATURES CLICK TOGUIDE CHANGE COPY P Commercial Immersion Blender parts Lock button Power/pulse trigger Speed control dial Bowl clamp 365 cm power cord Motor body Continuous run button Mounting knob Serviceable motor brushes Mount for bowl clamp, hub cap, and secondary handle Bowl clamp Stainless steel blending arm (5KHBC120 shown) Secondary handle Whisk attachment* *Accessory sold separately.
PARTS AND FEATURES GUIDE Optional accessories Model # Whisk attachment* *Accessory sold separately 5KHBC110WSS 254 mm Multipurpose S-blade 5KHBC112MSS 305 mm 5KHBC114MSS 356 mm 5KHBC116MSS 5KHBC118MSS 5KHBC120MSS or Recommended bowl size 5KHBC412OB 5KHBC414OB 5KHBC416OB 5KHBC418OB 5KHBC420OB Style Length (5KHB112SS shown) English Accessory 406 mm 457 mm 508 mm 22.7 litres bowl (maximum) 53.0 litres bowl (maximum) 87.1 litres bowl (maximum) 121.1 litres bowl (maximum) 151.
PARTS CMD +AND SHIFT FEATURES CLICK TOGUIDE CHANGE COPY C O Commercial Immersion Blender features Speed control dial Provides easy adjustment of speed with a turn of the dial, located at the base of the motor body. Powerful 1HP motor Provides powerful blending action designed for long-life operation. Power/pulse trigger Located on the handle and activated by pressing and holding during blending. To stop blending, simply release the Power/pulse trigger.
CMD + SHIFTTHE OPERATING CLICK COMMERCIAL TO CHANGE IMMERSION COPY BLENDER Before first use IMPORTANT: Do not immerse the motor body in water. Wash all the attachments and accessories by hand or in the dishwasher. Mild dish soap may be used, but do not use abrasive cleansers. Dry thoroughly with a soft cloth. English Before using the KitchenAid Commercial Immersion Blender for the first time, wipe the motor body with a clean, damp cloth to remove any dirt or dust.
OPERATING CMD + SHIFT THE CLICK COMMERCIAL TO CHANGE IMMERSION COPY BLENDER Using the Commercial Immersion Blender with blade attachment 1. Insert blending arm attachment into the motor body, twist to lock. The attachment mark on the blending arm should line up with the bottom of the motor bell when fully attached. 3. Set Commercial Immersion Blender to your desired speed on the speed control dial. 4. Insert the Commercial Immersion Blender into the mixture.
OPERATING THE COMMERCIAL IMMERSION BLENDER 5. Press the LOCK switch to unlock the Commercial Immersion Blender, then press and hold the Power/pulse trigger to activate. Lock Using a light circular motion from your wrist, draw the Commercial Immersion Blender up slightly and let it fall again into the ingredients. Allow your wrist motion and the weight of the Commercial Immersion Blender to do the work. Use the removable secondary handle, if needed, for extra stability while mixing.
OPERATING CMD + SHIFT THE CLICK COMMERCIAL TO CHANGE IMMERSION COPY BLENDER Using the Commercial Immersion Blender with the whisk attachment 1. Insert the whisk attachment into the motor body and twist to lock. The attachment mark on the whisk should line up with the bottom of the motor bell when fully attached. Electrical Shock Hazard Plug into an earthed outlet. Do not remove earth prong. Do not use an adapter. Do not use an extension cord.
OPERATING THE COMMERCIAL IMMERSION BLENDER 4. Insert the whisk into the mixture. For best results, insert the Commercial Immersion Blender with the whisk attached into the pot or bowl containing ingredients at an angle. Use your free hand to hold the pot or bowl or hold the Commercial Immersion Blender near the base of the motor unit for better stability. Remember to stop the Commercial Immersion Blender before removing it from the pot or bowl to avoid splashing.
OPERATING CMD + SHIFT THE CLICK COMMERCIAL TO CHANGE IMMERSION COPY BLENDER Using the bowl clamp and the continuous run feature IMPORTANT: Continuous run feature maximum recommended mixing times: 30 minutes — Low Speed 10 minutes — High Speed 1. Slide the notched latch into the bowl clamp at the slot in the top of the clamp; then, use the adjustment wheel to tighten into place at the correct spot for the bowl you are using to mix. 2.
CARE AND CLEANING Washing the motor body NOTE: To avoid damage to the Commercial Immersion Blender, do not immerse the motor body in washing solution, rinse water, or sanitizing solution. Always clean the Commercial Immersion Blender prior to initial use, after each use, and before storing. 1. Unplug the Commercial Immersion Blender before cleaning. 2. Remove the attachments by twisting (see "Operating the Commercial Immersion Blender" section). 3.
TROUBLESHOOTING CMD + SHIFT CLICK TO CHANGE COPY T If the Commercial Immersion Blender has stopped working, check for the following: Unit has been unplugged • Release the Power/pulse trigger. • Check the power supply. • Restart the Commercial Immersion Blender as instructed in “Operating the Commercial Immersion Blender”. Machine has overheated • Release the Power/pulse trigger. • Unplug the unit. • Wait a few minutes for the motor to cool down and the thermal safety mechanism to reset.
F A A (mm) B (mm) C (mm) E (mm) F (mm) G (kgs) 5KHBC112 73.4 420 723.4 383.9 101.5 115 4.3 5KHBC114 73.4 420 774.2 434.7 101.5 115 4.4 5KHBC116 73.4 420 485.5 101.5 115 4.5 5KHBC118 73.4 420 875.8 536.3 101.5 115 4.6 5KHBC120 73.4 420 926.6 587.1 101.5 115 4.7 825 D (mm) English TECHNICAL SPECIFICATIONS B C D E 21 W10859533A_01_EN_v18.
CMD + SHIFT TECHNICAL SPECIFICATIONS CLICK TO CHANGE COPY W EC - Declaration of conformity We declare under our sole responsibility that the product described under “Technical data” fulfills all the relevant regulations and the directives 2011/65/EU,2014/30/EU,2006/42/EC, 2009/125/EC and the following harmonized standards have been used: European Commission Regulation1275/2008 EN12853: 2001+A1:2010 EN55014-1:2006+A1:2009+A2:2011 EN55014-2:2015 EN61000-3-2:2014 EN61000-3-3:2013 11 November 2016 Mark Dahm
WARRANTY AND SERVICE Kitchenaid Commercial Immersion Blender warranty KitchenAid Will Pay For: Europe, Middle East and Africa: 5KHBC412EXX, 5KHBC412BXX, 5KHBC414EXX, 5KHBC414BXX, 5KHBC416EXX, 5KHBC416BXX, 5KHBC418EXX, 5KHBC418BXX, 5KHBC420EXX, 5KHBC420BXX Two years full warranty from date of purchase. The replacement parts A. Repairs when Commercial and repair labour costs to Immersion Blender is correct defects in materials used for operations other or workmanship.
©2017. All rights reserved. Specifications subject to change without notice. W10859533A W10859533A_back.