PW850PW850-GW Operating Manual Kisan Telecom 2009.
FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. INFORMATION TO THE USER This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Contents 1. Introduction .............................................................................................................................. 5 1.1. General Introduction....................................................................................................... 5 2. Network Network configuration of system ............................................................................................ 5 2.1. Network configuration..............................................................
/ 35
1. Introduction 1.1. General Introduction As an equipment to clear the shadows inevitably generated among the adjacent cells of WCDMA and GSM, PW850PW850-GW simultaneously simultaneously supports both WCDMA and GSM and effectively repeats the signals between terminals in dead area and BTS.
3. System Specifications 3.1.
RVS Noise Figure EVM or Rho Gain Control Range VSWR 5dB max. 5dB max. 12.5% DU : 20dB by 1dB Step RU : 20dB by 1dB Step 1.5 : 1 max. DU : 20dB by 1dB Step RU : 20dB by 1dB Step 1.5 : 1 max.
4. Mechanical Specifications 4.1. PW850PW850-GW DU 4.1.1.
4.1.2.
4.1.3. Mechanical specification No 1 Items Exterior view 2 Material 3 Connector Type 4 5 Power Input Input Ground 6 Communication Port Port Specifications 1. Shelf attachable type to both INDOOR and OPEN RACK 2. W 19” 19” (483mm) H 2U (88 (88mm) D (400 (400mm) 00mm) Aluminum (AL5052, AL6063) is mainly used for protection from corrosion by external environments. 1. Optic I/O: I/O: FC/APC at rear rear side 2. RF I/O: I/O: SMA Female at rear rear side 3.
4.1.5.
4.1.6. Module Composition No ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ Module DU FWD Amp for GSM (DFA(DFA-G) DU FWD Amp for WCDMA (DFA(DFA-W) DU RVS Amp(DRAAmp(DRA-WG) 2Way Divider DU Optical Transceiver Unit (DOU) FSK Modem DU RVS/FWD Combiner for W/G (DRFCOM(DRFCOM-WG) PSU NMS Controller Interface BD 12 / 35 Voltage Used 6.5Vdc 6.5Vdc 6.5Vdc 6.5Vdc 6.5Vdc 9Vdc 6.
4.1.7 Function of Modules Modules No Module Functions 1 [DFA[DFA-G] Checks and controls controls the forward signal from GSM BTS and support -20dB monitor port of module input. 2 [DFA[DFA-W] Checks and controls controls the forward s signal ignal from WCDMA BTS and provides -20dB monitor port of module input. 3 [DRA [DRA] Checks the reverse power level from RU, checks and controls the output power to GSM BTS. Provides -20dB monitor port of module output.
OUTPUT SWITCH AC_L +9V GND +9V GND +6.5V GND AC_N INPUT +6.5V GND ALM GND F.G YW396-05V(연호전자) [PSU Capacity] Capacity] Output Maximum Voltage current +9V 3A +6.5V 5A PWR ON Watt 59.5 W [PSU Pin Map] Map] SWITCH PIN Type: ype: YW396YW396-02V Pin no. 1 2 Spec. Switch_IN Switch_Out INPUT PIN Type: ype: YW396YW396-05V Pin no. 1 2 Spec. AC_L N.C 3 AC_N 4 N.C 5 F.G OUTPUT PIN type: 55665566-10 (MOLEX) MOLEX) Pin no. 1 2 3 Spec. ALARM +6.5V +6.5V Pin no. 6 7 8 Spec.
/ 35
4.2. PW850PW850-GW RU 4.2.1.
4.2.2.
4.2.3. Mechanical Specification No 1 2 3 Item Dimension Method of Cooling Method of Door Locking 4 Optic I/O 5 ANT PORT 6 Power Input 7 Ground Waterproof condition 8 9 Major Features Description W 450mm 450mm H 630mm 630mm D 255mm 255mm (plinth included) Natural convection (Heat (HeatHeat-sink) sink) Two (2) locks on the right side of the front of cabinet (enclosure) 1. inside: inside: FC/APC * Optic cable tray is provided in the inside of cabinet.
6 7 8 9 RxD PSU HPA1 HPA1 HPA2 LD PD RESET DEBUG DISPLAY DATA INPUT Green: data receiving from DU, OFF(Gray): no data receiving Green: PSU normal, Red: PSU Alarm Green: HPA normal, Red: HPA alarm Not used Green: Normal, Red: Alarm Green: Normal, Red: Alarm NMS Board Hardware Reset Connection port to GUI program (9pin DD-SUB) VFD display system showing version, status, etc.
4.2.6. Module Composition No ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ ⑫ Module RF FWD AGC for W/G (RFAGC(RFAGC-WG) RF FWD Channel Selector (RFCHS) Slave Optical Transceiver unit (SOU) RF Modem (FSK Modem) RU RVS COM for W/G (RRCOM(RRCOM-WG) RU RVS Channel Selector (RRCHS) RU RVS LNA for W/G (RRLNA(RRLNA-WG) HPA FrontFront-End Filter Unit (FE(FE-Duplexer) PSU NMS Controller Interface BD 20 / 35 Voltage Used 6.5Vdc 6.5Vdc 6.5Vdc 6.5Vdc 6.5Vdc 6.5Vdc 9Vdc 9Vdc 6.5Vdc 6.5Vdc 9Vdc 9Vdc 27Vdc 27Vdc 9Vdc 9Vdc 6.
4.2.7. Function of Modules No Module Description 1 [RFAGCRFAGC-WG] Divides RF signal (GSM and WCDMA) and modem signal 2 [RFCHS[RFCHS-G] Controls the level of GSM FWD output signal and ALC function. Transmits module output to HPA. 3 4 [SOU] Converts E/O (or O/E) of FWD and RVS signals.
11 [NMS] NMS] Monitors/controls the status and configurable items of RU and module in RU 12 [Interface BD] BD] Provides DC current to modules which are connected to interface B’ B’D and supports a connection port to communicate with NMS B’ B’D. 4.2.8. PSU PSU converts external AC110V into DC and supplies +27V, +9V and +6.5V to modules in RU. In PSU, there two (2) on/off switches; one is for AC110V, another is for HPA only. The drawing of PSU is below.
SUB Output PIN Type: Type: 55665566-10P (Molex) Pin No. 1 2 3 Spec. +9V +9V +6.5V Pin No. 6 7 8 Spec. GND GND GND 4 +6.5V 9 GND Circuit Diagram of Power Power 23 / 35 5 +6.
5.
6. Level Budget 6.1. Forward Path 6.2.
7. GUI Program (RptMan) PW850-GW and provides status GUI program (RptMan) is a management program for PW850 monitoring and control functions to users. 7.1. System Requirement System: System: Desktop or laptop PC OS: Windows XP or later Resolution: Resolution: 1024 768 or more Connection Cable: 9 pin serial serial cable (cross (cross type) type) 7.2. Cable connection The cable connection between repeater and PC (GUI program) is illustrated below.
Presents working menu for operators. Toolbar Work Space Presents icons (button type) for frequently used command. Icons are activated or disabled as to the status of repeater. Provides the working space of windows or dialogs. 7.4. Status Display Status of repeater is displayed by LED and values. The meanings are below. LED Alarm: / blinking means ALARM, means NORMAL On/Off: ON, OFF ON, Exception) is ON, is OFF Exception) for HPA, HPA, ON, Value Units are not displayed (omitted).
View Window Donor Window Remote Window Cascade Tile Horizon Packet Debug Help About RptMan 7.7.
7.8.3.
USE: Shows and controls the using status of module (green for in use, gray for not in use) IN PWR: Input power level (b (box), ox), alarm status (LED) IN UPR: Value/control of upper threshold of input power (b (button), upper alarm status (LED) IN LWR: Value/control of lower threshold of input power (button), lower alarm status (LED) ATT: Value/control of attenuation (button) USE: Shows and controls the using status of module (green for in use, gray for not in use) OUT PWR: RVS output power (b
USE: Shows and controls the using status of module (green for in use, gray for not in use) OUT PWR: RVS RVS output power (box), alarm status (LED) OUT UPR: Value/control of upper threshold of RVS output power (button) and alarm status (LED) ALC: Value/control of level of ALC (button) and effective operating status of ALC function (LED) ATT: Value/control of the attenuation (buttons) for adjusting RVS level ALC ATT: Value of attenuation automatically operated by ALC function (boxes) PLL: Contro
7.8.4.
USE: Shows and controls the using status of module (green for in use, gray for not in use) IN PWR: Input power level (box), alarm status (LED) OUT PWR: PWR: Output power level (box), alarm status (LED) ALC: Value/control of level of ALC (button) and effective operating status of ALC function (LED) ATT: Value/control of the attenuation (buttons) for adjusting FWD level ALC ATT: Value of attenuation automatically operated by ALC function (box) PLL: Control the setting value of PLL (button) and a
On/Off: Status/control the operation state of HPA OVPWR: Alarm status of HPA OverOver-Power (LED) VSWR: Alarm status of HPA VSWR (LED) OVTMP: Alarm status of HPA OverOvertemperature OUT PWR: Output power level of HPA (box) OUT UPR: Value/control of upper threshold of HPA output power (button), alarm status (LED) OUT LWR: Value/control of lower threshold of HPA output power (button), alarm status (LED) ASD(Auto ASD(Auto Shutdown): Shutdown): ASD level (button), e running status of function (L
Appendix A Initial setting values (Factory Setting) DU RU Optic Category DFA-W ATT DFA DFADFA-G ATT DRA ATT ALC Shut Down ALC Level Shut Down Level Input Level RFAGC ATT RFCHS ATT RRCHS ATT ALC Shut Down ALC Level Shut Down Level LD High Level LD Low Level Level PD High level PD Low Level Value 30dB 30dB 30dB OFF ON -40dBm -30dBm -40 ~ -10dBm 30dB 30dB 20dB OFF ON 37dBm 39dBm 8dBm 3dBm 7dBm -4dBm 35 / 35 Remarks
