Quick Guide

T450 PoC Radio
Quick Guide
Appearance
No. Name
Radio
Battery
Antenna
USB cable
Power adapter
Quick Guide
Safety Information
Strap
Desktop charger (optional)
Charging the Battery
Attachments
Method 1: Charging through Micro USB Cable
1. Connect the power adapter to an AC power socket as required.
2. Power off the radio. Connect one end of the micro USB cable to the
power adapter, and the other end to the USB port on the radio.
Red indicator light is on.
Method 2: Desktop charger
1. Plug the power adapter into a qualified AC power socket.
2. Connect the USB cable of the power adapter to the USB port at the
back of the desktop charger. Green indicator light is on.
3. Insert the battery only or together with the radio into the desktop
charger.
4. Make sure the battery contacts the charging points properly and
red indicator light is on.
5. When the indicator light turns from red to green,
charging is finished.
Installing the Battery
Installing a SIM Card
1. Remove the battery and find the SIM card holder in the upper part
of the battery holder. Push the cover of the SIM card holder
rightwards and then open the cover.
2. Insert a Nano-SIM card into the guide slot of the cover, and make
sure the card is in position.
3. Press the cover of the SIM card holder back onto the holder, and
push the cover leftwards to lock it.
Note: Please use a standard Nano-SIM card.
Indicator State
Device State
Red light on
Green light on
Blue light on
Red light flashing fast
- SIM card not installed or installed improperly.
(Voice prompt “No SIM card”.)
- Failed to unlock PIN code of SIM card.
- In individual/group/all call
- Downloading/playing back voice record.
In individual-call standby state.
Network registration failed due to inactivated or
overdue SIM card.
Green light flashing slow
Blue light flashing fast
Network registration succeeded. Enter standby state.
- Registering to a network.
- Device not configured on the server.
(Voice prompt “Not configured”.)
- Device expired.
In power-off state.
Programmable keys
No.
Function
Description
Alarm on/off
Remaining battery
capacity announcement
User announcement
Group announcement
Playback
Bluetooth on/off
Wi-Fi on/off
Individual Call
All Call
Send/quit an emergency alarm.
Announce remaining battery capacity.
Announce the user name of the radio.
Announce the current group in which
the radio is in.
Play back the latest 99 voice records.
Enable/disable Bluetooth function.
Enable/disable Wi-Fi function.
Make a quick individual call.
Broadcast
To suit you operation habits, programmable keys 1 and 2 are
provided. You may enable various functions on these keys using
the CPS. The functions are listed as below.
Icons
Icon
Description
2G/3G/4G received signal strength
2G/3G/4G transmission
Wi-Fi signal strength
Searching GPS signal
GPS signal acquired
In group call
In individual call
In all call
Remaining battery capacity
Short message
2G,3G,4G
Bluetooth enabled
Connected to Bluetooth device
In emergency alarm
Alarm message
Basic Operation
1. Powering On/Off
To power on the radio, rotate the ɋPower/volume knobɌ clockwise until you
hear a tick. Wait a while. The screen backlight and yellow indicator light is on,
and the message “Starting” is displayed on the screen.
To power off the radio, rotate the
ɋPower/volume knobɌ counterclockwise until
you hear a tick.
2. Adjusting the Volume
Rotate the ɋPower/volume knobɌ clockwise to increase the volume, or
counterclockwise to decrease it.
3. Individual Call
- In the standby status, press the ɋOK Ɍkey, select ɋContactsɌ, and
choose a contact.
- Press the ɋOK Ɍkey, select ɋInitiate Individual CallɌYou will hear a voice
prompt “Enter individual-call mode”.
4. Group Call
ŚInitiating Group Call
Under individual/group/broadcast call mode, you can call the members of a
group by pressing the
ɋPTTɌkey. If there is no member online, you will hear a
voice prompt “No member online”, and transmission will be terminated.
Note: A group is set through the network management system.
śSwitching Groups
Method 1: After the radio registers successfully and enters standby state, rotate
theɋGroup knobɌto select a group.
Method 2: In the standby interface, press the
ɋMenuɌkey to enter the Menu
interface, press navigation keys to selectɋGroup ListɌand then a
group, and then press theɋOKɌkey.
Troubleshooting
Stun
Kill
Channel knob
LED
Navigation
keys
Back key
Display Key
Speaker
Earphone jack
USB port
Charging
contact
Strap hole
Power/
volume knob
Playback key
Menu/ok
key
Microphone
PTT key
Programmable
key 1
Programmable
key 2
Belt clip
Antenna
Please read carefully the Safety Information before using the product.
This document is only for reference, and actual product prevails.
Kirisun reserves the right to the final interpretation of this document.
Method 1
Method 2
LED Indicator
5. All Call
After programming an all-call key through the CPS, you may enter all-call mode
by pressing the key, and then initiate an all call by pressing the ɋPTTɌ key.
An all-call should be answered within 3 seconds,otherwise it will be qiutted.
An all-call can interrupte an individual call or a group call.
6. Broadcast Call
After programming a broadcast-call key through the CPS, you may enter
broadcast-call mode by pressing the key, and then initiate a broadcast call by
pressing the ɋPTTɌ key. An broadcast-call should be answered within 3
seconds, otherwise it will be qiutted.An broadcast-call can interrupte an individual
call or a group call.
7. Receiving a Call
By switching to a group set through the NMS, the radio can receive an individual
call, a group call or an all call from the group and output voice.
8. Late Entry
This function enables the radio to join an undergoing group call after a delay.
9. Priority Call
Different call priority can be set on the radio. A radio with a higher call priority
initiates a call prior to a radio with a lower call priority.
Note: The default call time of all types of calls is 60 seconds, which is modifiable
through the NMS. A call is terminated automatically after this time is up.
10. Playback
After voice recording and playback are enabled on the NMS, you can download
and play back the latest 99 voice records by pressing a pre-programmed
playback key.
12. Low-Power Alert
When the remaining battery of the radio is below 10%, you will hear the voice
alert “Low power.” at a certain interval. Please replace or charge the battery
after powering off the radio.
11. Positioning
To enable or disable GPS positioning, go to the standby interface, press the
ɋOkɌ key, selectɋSettingɌand thenɋGPSɌ, and slide the switch.
The GPS module inside the radio locates the radio and reports position
information to the NMS. The real-time location and movement track of the radio
can be displayed on a GIS map on the NMS or a dispatcher.
13. Wi-Fi
To enable or disable Wi-Fi, go to the standby interface, press theɋOkɌkey,
selectɋSettingɌand thenɋWi-FiɌ, and slide the switch.
By enabling Wi-Fi, you can search Wi-Fi networks nearby in real time. The
radio can only be connected to a Wi-Fi hotspot, which should be preset through
the CPS. To view or select from preset hotspots, go to Saved Network.
14. Bluetooth
To enable or disable Bluetooth, go to the standby interface, press theɋOkɌkey,
selectɋSettingɌand thenɋBluetoothɌ, and slide the switch.
After enabling Bluetooth, you can connect the radio to a Bluetooth earphone by
scan.
15. Short Message
To view sent short messages, go to the standby interface, press theɋOkɌkey,
and select
ɋMessageɌ, Short Message and then Inbox.
16. Mobile Networks
GSM, WCDMA, TDD-LTE and FDD-LTE networks are supported.
17. Advanced Functions
Revive, stun, kill, monitoring and voice playback can be achieved through the
dispatcher.
18. Emergency Alarm
The radio supports manual alarm. After programming an emergency alarm key
through the CPS, you can press the key to send or quit an emergency alarm.
There are two modes of an emergency alarm.
- Silent Alarm: In this mode, the radio sends an alarm silently, but receives an
alarm with a voice prompt “Alarm from ***”.
-Alarm and Call: If silent alarm is disabled, the radio sends an alarm and rings a
siren, but receives an alarm with a voice prompt “Alarm from***” and rings a
siren.
To view the alarms sent and received, go to the standby interface, press the
ɋOkɌkey, and select ɋMessageɌ, ɋSOS MessageɌ.
167W06000079
Version：V1.0
- Press the ɋPTTɌ key.
Ś Initiating Individual Call
ś Ending Individual Call
An individual call can be ended in either of the following ways.
- During an individual call, press the ɋOK Ɍkey, selectɋContactsɌ, and
select End Individual Call.
- After entering individual-call mode, if you do not press theɋPTTɌkey within
30 seconds, the radio will quit this mode, and you will hear a voice prompt
“Individual call timed out”.
Installing the Battery
1. Press the upper part of the belt clip gently so that it springs up.
(Figure ①)
2. Insert the two positioning columns at the top of the battery into the
corresponding holes at the back of the radio, and push the battery
upwards until it reach the upper edge of the battery slot. (Figure ②).
3. Press the battery down, and you will hear a “da” sound. The battery
is installed. (Figure ③)
Uninstalling the Battery
1. Press the upper part of the belt clip gently so that it springs up.
(Figure ④)
2. Unlock the battery latch by pushing it to the right, and the battery will
go up. (Figure ⑤).
3. Take off the battery. (Figure ⑥)
ŜśŚ
ŝ Ş ş
No light
No.
Problem
Solution
Power-on failed
Small voice
Communication
failed
Reason: Speak too far from the
microphone.
Solution: The suggested distance is
3~10 cm from the mouth.
Reason: Wrong volume setting.
Solution: Increase the volume.
Reason: The battery is used up.
Solution: Charge or replace the battery.
Reason: Volume switch is faulty.
Solution: Get it repaired at the specified
service station.
Reason: SIM card expired.
Solution: Renewal or replace the card.
Reason: Incorrect group setting.
Solution: Choose a correct group and try
again.
Reason: PoC platform service expired.
Solution: Renew PoC platform service
again.
Make a all-call.
Make a broadcast-call.
FCC Statement IC Statement
RED Statement
15.19 Labeling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
15.105 Information to user.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information:
This product meets the government's requirements for exposure to radio waves.
The guidelines are based on standards that were developed by independent
scientific organizations through periodic and thorough evaluation of scientific
studies. The standards include a substantial safety margin designed to assure the
safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6
W/kg averaged over one gram of tissue. This device was tested for typical body-
worn operations when the device used at 25mm from front face and 10mm from
the product, 0mm from the belt, for maintain compliance with FCC RF exposure
requirements. The use of belt clips, holsters and similar accessories should not
contain metallic components in its assembly. The use of accessories that do not
satisfy these requirements may not comply with FCC RF exposure requirements,
and should be avoided.
This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions:
(1)This device may not cause interference;
(2)This device must accept any interference, including interference that
may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d'en compromettre le fonctionnement.
Specific Absorption Rate (SAR) information:
This product meets the government's requirements for exposure to radio waves.
The guidelines are based on standards that were developed by independent
scientific organizations through periodic and thorough evaluation of scientific
studies. The standards include a substantial safety margin designed to assure the
safety of all persons regardless of age or health.
IC RF Exposure Information and Statement The SAR limit of USA (IC) is 1.6 W/kg
averaged over one gram of tissue. This device was tested for typical body-worn
operations with the back of the handset kept 10mm for body worn. To maintain
compliance with IC RF exposure requirements, use accessories that maintain a
25mm from front face and 10mm from the product, 0mm from the belt. The use of
belt clips, holsters and similar accessories should not contain metallic components
in its assembly. The use of accessories that do not satisfy these requirements may
not comply with IC RF exposure requirements, and should be avoided.
1. Risk of explosion if battery is replaced by an incorrect type. Dispose of used
batteries according to the instructions.
2. The product shall only be connected to a USB interface of version USB2.0 or
higher.
3. Adapter shall be installed near the equipment and shall be easily accessible.
4. The operating temperature of the EUT can’t exceed 40℃ and shouldn’t be
lower than -20℃.
5. The plug considered as disconnect device of adapter.
6. The device complies with RF specifications when the device used at 25mm
from front face and 5mm from the product, 0mm from the belt.
7. Use careful with the earphone maybe possible excessive sound pressure from
earphones and headphones can cause hearing loss.
Hereby, Kirisun Communication Co.,Ltd. declares that this Mobile phone product
is in compliance with essential requirements and other relevant provisions of
Directive 2014/53/EU. This product is allowed to be used in all EU member states.
und pressure fr