Specifications

Battery\
e
LED indicator state
Terminal state
Red light on
Green light on
Orange light on
Transmitting signals
Receiving a signal (voice, message, data)
or detecting activity on the channel.
The radio receives the call within the automatic reset
time (Analog). During call hang time(Digital).
Orange light flashing
Red light flashing
The radio is in an alarm state or receives
a call prompt, or during a channel scan.
The battery is low or is receiving an emergency alarm, or
the radio fails to post, or is reading / writing
frequency.
LCD Display
167W06000109
Version：V1.0
The final interpretation of this manual is vested in Kirisun.
Any product changes shall prevail without prior notice.
Battery
9
Install/Uninstall Antenna
Install/Remove Back Clip
Align the two screws of the back clip with the two screw holes on the back of
the mainframe and tighten them with a screwdriver; when removing, loosen the two
back clip screws to remove the back clip.
Install Accessories
Insert the external audio accessories into the comm port and fasten it with screws.
As shown in ①, align the antenna with the interface at the
radio top, and turn it clockwise to fasten.
For uninstall the antenna, tum the antenna counter-clockwise
as shown in ② to take it out.
Basic Operation
1) Initiate a call to default contact.
If your device has a default contact in the current channel,
you can press and hold the PTT key to initiate a call directly
to the default contact.
You can preset a default contact for each digital channel
through the reseller.
2) Select a contact and initiate a call. Go to the contacts
menu, select the contact you want to call in the contact list,
and press and hold the PTT key to initiate the call.
3) Dial manually and initiate a call.
Go to the contacts menu, choose Manual Dial, and enter the ID
you want to call, and press and hold the PTT key to initiate
the call.
Common Failure and Troubleshooting Methods
No. Phenomenon
Causes and troubleshooting methods
Fail to power on
Unable to receive
signal
Unable to talk
A. Whether the battery has power, if
the battery is insufficient, please
recharge or try again with a new battery.
B. The power connection contact is out
of contact with the battery, reinstall
and try again.
C. The battery contact is dirty or
damaged, resulting in poor contact. Clean the
battery contact and try again.
A. The two radio frequencies do not match,
reselect the channel with the same
frequency.
B. The CTCSS/CDCSS signalling are different,
so reset them up through computer.
C. Out of range.
A. The two radio frequencies do not
match, reselect the channel with the
same frequency.
B. The CTCSS/CDCSS signalling are
different, so reset them up through
computer.
C. Out of range.
1. In the power-off state, turn the knob clockwise until you hear the
"pa" sound to power on. The LCD display shows the boot screen, and the
backlight turns on automatically. The radio emits a "Didi" tone.
In the power-on state, turn the knob counterclockwise until you hear
the "pa" sound to turn it off.
2. Select channel.
In the standby interface, rotate the channel knob to select the
channel.
Each channel of the radio can be configured as an analog channel or a
digital channel, and the channel knob can be rotated to switch between
the analog channel and the digital channel.
3. Adjust volume.
In the power-on state, rotating the power knob can adjust the volume,
rotating clockwise can increase the volume, and rotating
counterclockwise can reduce the volume.
After rotating counterclockwise to the minimum volume, if you continue
to rotate, the machine will be turned off when you hear the "pa" sound.
4. Initiate a call.
5.Receive a call
When a call is received, the radio automatically switches to the receiving
state.
1)LED green light on
2)LCD display call type icon(single call, group call), alias or ID,and
incoming call icon.
3)Play the received voice
4)While waiting for another user to stop calling, you can immediately
press and hold the PTT key to call back the current contact during the
call hang time.
Attention:
To receive calls from a group, the radio must be set to be a member of
the group (the dealer can write through the frequency writing software)
1)In the search device interface, select a device to connect.
2)If there is a Bluetooth device that has been connected to this device
before, when the Bluetooth of this device is turned on, it will connect
automatically.
6. Emergency alarm.
In case of emergency, you can send an emergency alarm message with
confirmation and an emergency voice to the specified user group through the
emergency alarm function. You can initiate an emergency alarm at any time,
even if the current channel is receiving a signal.
7.Call log
Through the call logging feature, you can view and manage recent out call,
incoming call and missed calls. The call record saves only single call and
does not record the group call.
8. Connect Bluetooth device (non-standard feature).
There are two ways to connect Bluetooth devices:
A. Check whether the antenna is a dual-mode
antenna, if not, replace it with a dual-
mode antenna.
B. Check whether the GPS setting status is
correct, if not, reset.
C. The device is in a signal shielded
environment, please re-position in an
open area.
A. The connection is incorrect. Check whether
the connection is correct.
B. Whether the computer USB driver is
installed, if not, install it.
C. Poor contact with the headphone interface
board, check whether the interface board is
good, if not, replace the headphone
interface board.
4
5
GPS does not locate
Programming abnormal
1 2
3 4
DP810&DP815 Digital Explosion-proof
Two-way Radio
/
Battery
Back key
/Back to
standy interface key
Down key
LCD
/
1
PTT key
2
1. Gently press the upper end of the back clip to make the back clip pop
up.
2. Align the battery snap with the main radio aluminum alloy snap.
3. Lower the battery into the main radio battery slot.
4. Push the battery to the correct position.
电池卡槽
aluminum alloy snap
Hotline: [phone]
Fujian Kirisun Communication Ltd,.
LED Indicator
High power
Single call
Low power
Mute
Unread message
State message
Battery indicator
Less space indicates more battery power when the
battery is low the icon will turn red.
Signal strength
More bars indicate strong signal and less bars mean
weak signal, it only shows up when receiving.
Full mailbox
Keypad lock
Emergency mode
Encryption
Man Down
VOX
Initiating a call
Receving a call
Talk around
Alarm
Roam
GPS enabled, but available GPS date not received
GPS positioned
Icon rotation, scanning channel
The scan stays on priority channel 1
The scan stays on priority channel 2
The scan stays on normal channel
ID Type
Group call
All call
Menu option selection
This option selected
This option unselected
CE Warning
1. Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
2. The product shall only be connected to a USB interface of version USB2.0 or higher.
3. Adapter shall be installed near the equipment and shall be easily accessible.
4. The operating temperature of the device can’t exceed 55℃ and shouldn’t be lower
than -20℃.
5. The plug considered as disconnect device of adapter.
6. The device complies with RF specifications when the device used at 20cm from the body.
Hereby, Kirisun Communication Co.,Ltd. declares that this product is in compliance with
essential requirements and other relevant provisions of Directive 2014/53/EU. This product
is allowed to be used in all EU member states.
FCC /IC Warning:
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Pour contrôler votre exposition et garantir le respect des limites d'exposition en
milieu professionnel / contrôlé, respectez toujours les procédures suivantes.
Des lignes directrices:
• Ne retirez pas l'étiquette d'exposition RF de l'appareil.
• Les instructions de sensibilisation de l'utilisateur doivent accompagner
l'appareil lorsqu'il est transféré à d'autres utilisateurs.
• N'utilisez pas cet appareil si les exigences opérationnelles décrites ici ne sont
pas satisfaites.
Mode d'emploi:
This radio is designed for and classified as “Occupational/Controlled Use Only”,
meaning it must be used only during the course of employment by individuals
aware of the hazards, and the ways to minimize such hazards; NOT intended
for use in an General population /uncontrolled environment.
- DO NOT operate the radio without a proper antenna attached, as this may
damage the radio and may also cause you to exceed RF exposure limits. A
proper antenna is the antenna supplied with this radio by the manufacturer
or an antenna specifically authorized by the manufacturer for use with this radio.
- DO NOT transmit for more than 50% of total radio use time, more than 50%
of the time can cause RF exposure compliance requirements to be exceeded.
-This transmitter may operate with the antenna(s) documented in this filing in
Push-to-Talk and body-worn configurations. The device complies with RF
specifications when the device used at 25 mm from your front face and 0 mm
from your body