Operation Manual Image 87 & 47 DMX Image 87 Yoke Mount Image 47 Pole-Op Part No.
Image 87 & 47 Fixtures Image Yoke Mount IMG-87X-120 Image 87 DMX Yoke Mount, 120VAC IMG-87X-230 Image 87 DMX Yoke Mount, 230VAC IMG-47X-120 Image 47 DMX Yoke Mount, 120VAC IMG-47X-230 Image 47 DMX Yoke Mount, 230VAC Image Pole-Op IMG-87P-120 Image 87 DMX Pole-Op, 120VAC IMG-87P-230 Image 87 DMX Pole-Op, 230VAC IMG-47P-120 Image 47 DMX Pole-Op, 120VAC IMG-47P-230 Image 47 DMX Pole-Op, 230VAC Included w/ all Image Models LVR-I80-S Image 87 Silver Louver (Included) LVR-I40-S Image 47 Silver Louver (Included
True Match® Lamps 488-K29-S 488-K32-S 488-K55-S 488-K10-S 488-K5-S 4ft Kino KF29 4ft Kino KF32 4ft Kino KF55 4ft Kino 800ma 420 Blue 4ft Kino 800ma 525 Green Note: Kino Flo recommends Safety-Coated 420nm Blue for Bluescreen and 525nm Green for Greenscreen. Image Yoke Mount Kits KIT-I87-X1/120 Image 87 DMX Kit, 120VAC KIT-I87-X1/230 Image 87 DMX Kit, 230VAC Image 87 DMX Kit Kit Contents: 1 Image 87 DMX 1 Jr. Pin 1 Ship Case Dimensions: 57.5 x 8 x 35.5” (146 x 20.
KIT-I87-X4/120 Image 87 DMX Kit, 120VAC (4-Unit) KIT-I87-X4/230 Image 87 DMX Kit, 230VAC (4-Unit) Image 87 DMX Kit (4-Unit) Kit Contents: 4 Image 87 DMX 4 Jr. Pin 1 Ship Case Dimensions: 35.5 x 33.5 x 64” (90 x 85 x 163cm) Weight: 365 lb (166kg) KIT-I47-X1/120 Image 47 DMX Kit, 120VAC KIT-I47-X1/230 Image 47 DMX Kit, 230VAC Image 47 DMX Kit Kit Contents: Dimensions: 1 Image 47 DMX 57.5 x 9 x 25.5” 1 Jr. Pin (146 x 23 x 65cm) 1 Ship Case Weight: 47 lb (21.
Inserting Gel Frame The gel frame is secured to the fixture by 4 spring-loaded pins. Align the pins of the gel frame with the oval receptacle holes on the edge of the fixture. Pull back the pins and release into the receptacles to properly secure the gel frame. Applying Gel to Frame A) The Gel Frame comes with gel clips. Cut the gel to size and use the clips to fasten the gel to the frame. Note: It is recommended to attach one clip on all four sides and two clips near all four corners of the Gel Frame.
Mounting Barndoors Side Door (x2) Top/ Bottom Door (x2) Side Doors 1) Align the hinge bracket tabs with the two square receptacles on the side of the fixture. 2) Press the tabs of both brackets into the square receptacles. 3) Slide the two brackets up until the silver lock pin snaps into place. 4) To release the barndoor, press the lock pin down and slide the bracket in reverse. Top and Bottom Doors 1) Align the two hinge bracket tabs with the two square vents closest to the silver lock pins.
Image Yoke Mount The Yoke has a ½” hole to accept industry standard mounting hardware. The Image 87 Yoke Mount can hang from a grid by a junior pipe hanger using a Junior Pin Assembly for Yoke (MTP-I80), sold separately. The Image 47 Yoke Mount can also hang from a grid by a junior pipe hanger using a Junior Pin Assembly for Yoke (MTP-I80) or hang from a baby pipe hanger using a Baby Receiver Assembly for Yoke (MTP-I40), both sold separately.
Image Pole-Op The Image 87 and 47 Pole-Op fixtures include a yoke with an attached junior pin. They can be hung from a grid with a junior pipe hanger. Junior pin attached to Pole-Op Yoke Pole Operation The Blue cup alters the Pan (left or right). The White cup alters the Tilt (up or down). Warning! Do not pull yoke to adjust tilt. Turn the white knob counter clockwise to angle the yoke 90°. (ParaBeam shown for illustration purposes only.
Image 87 DMX Control Panel A B C D E FG H A) Manual Selector Dial: Turns lamps on and off manually without connecting DMX cable to fixture. B) HO/Std Selector Switch: HO setting operates lamps at High Output; Std setting operates lamps at Standard light output. Note: Std is ½ f-stop lower than HO. C) Power Switch: Turns fixture on and off. Has built-in indicator light to detect if AC power is present in power cord. “O” = OFF position. D) Fuse: Provides circuit protection.
Manual Operation The Image 87 & 47 DMX fixtures may be operated manually with the Manual Lamp Selector Dial. The selector dial enables you to turn lamps on and off with an “inside-out” pattern. Note: If all lamps are on, the outside tubes will turn off first. HO operates lamps in High Output mode. Std operates lamps in Standard Output mode. Image 87 Lamp Switching Image 47 Lamp Switching Note: All manual functions are disabled as soon as DMX cables are applied.
DMX Operation DMX Addressing Prior to hanging any instruments, set the DMX address of each fixture. Push the tabs above or below the number window to set the address. (Valid addresses range from 001 to 512.) The light above the address block will illuminate if a DMX signal is present. Tip: Power is not required to set DMX addresses. Therefore, DMX addresses can be set for each fixture prior to hanging.
DMX Channels Image 87 operates on DMX Channel 1 or 9 Lamps = 1-8, HO/Std = 9 On DMX Channel 1, one DMX address controls all 8 lamps on one dimmer channel. Channels 2-7 are not used. A 9th address controls the HO/Std setting. On DMX Channel 9, the first 8 addresses control 8 lamps individually. After the first DMX address is entered, the Image 87 automatically assigns 8 addresses to lamp positions 1-8, and address 9 controls the HO/Std setting.
Dimmer level – Lamp sequence Sliding the fader on the dimmer board from 0% ~100% controls the number of lamps that are on within a fixture. Note: The lamps may respond ± 4 slider channel levels, depending on the dimmer board.
One of the best applications for DMX Channel 1 mode is when lighting Blue and Green Screens or large Cycloramas. For example: One row of Image 87 fixtures can be set to DMX Channel 1 on a common address. When the fader on the dimmer board is brought up or down, all the fixtures on that address will have the same lamps turned on. Assigning the 9th address (5th address on Image 47) on all the fixtures renders control over the HO/Std settings.
Auto Terminate Each Image 87 & 47 DMX fixture has an “AUTO TERMINATE” feature. The last fixture that does not have an XLR cable attached to the DMX “Out” port will automatically terminate. Any theatrical lighting board with DMX512 protocol can be used to individually turn on/off lamps in a fixture. Image fixtures can be jumpered using the IN and OUT ports. As many as 100 fixtures can be jumpered on one chain as long as the DMX cable run remains under 1000 feet or 40 x 25ft DMX cables.
Accessories 16 BRD-I80 Image 87 Barndoors (Set of 4) BRD-I40 Image 47 Barndoors (Set of 4) MTP-I80 Junior Pin Assembly for Yoke (28mm) MTP-I40 Baby Receiver Assembly for Yoke (16mm) XLR-525 5-Pin xlr DMX Cable, 25ft XLR-515 5-Pin xlr DMX Cable, 15ft
True Match® Lamps 488-K29-S 488-K32-S 488-K55-S 4ft Kino KF29 4ft Kino KF32 4ft Kino KF55 488-K10-S 488-K5-S 4ft Kino 800ma 420 Blue 4ft Kino 800ma 525 Green Note: Kino Flo recommends Safety-Coated 420nm Blue for Bluescreen and 525nm Green for Greenscreen. Cases KAS-I80-1 KAS-I80-2 KAS-I80-4 Part Number Description Dimensions Weight (Empty) Holds KAS-I40-1 Image 47 Ship Case 57.5 x 9 x 25.5” (146 x 23 x 65cm) 27.5 lb (12.5kg) Image 47 KAS-I80-1 Image 87 Ship Case 57.5 x 8 x 35.
Fixture Specifications Model: IMG-87X Image 87 DMX Yoke Mount Image 87 Yoke Mount Input Voltage: 120VAC or 230VAC Output Frequency: 25kHz Amperage: 4.8A at 120VAC 2.4A at 230VAC Lamp Switching: 1~8 Output Switching: HO/Std Weight w/ lamps: 39 lb (18kg) Dimensions: 54 x 28 x 6.5” (137 x 71 x 16.5cm) Lamp Type: F75T12 Model: IMG-47X Image 47 DMX Yoke Mount Image 47 Yoke Mount 18 Input Voltage: 120VAC or 230VAC Output Frequency: 25kHz Amperage: 2.3A at 120VAC 1.
Model: IMG-87P Image 87 DMX Pole-Op Image 87 Pole-Op Input Voltage: 120VAC or 230VAC Output Frequency: 25kHz Amperage: 4.8A at 120VAC 2.4A at 230VAC Lamp Switching: 1~8 Output Switching: HO/Std Weight w/ lamps: 43 lb (19.5kg) Dimensions: 54.5 x 28 x 6.5” (138.4 x 71 x 16.5cm) Model: IMG-47P Image 47 DMX Pole-Op Image 47 Pole-Op Input Voltage: 120VAC or 230VAC Output Frequency: 25kHz Amperage: 2.3A at 120VAC 1.1A at 230VAC Lamp Switching: 1~4 Output Switching: HO/Std Weight w/ lamps: 25 lb (11.
For latest Warranty information and Certifications, see Kino Flo website at www.kinoflo.com. Environmental: Disposal of Old Electrical & Electronic Equipment. This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. This product is made of recyclable materials and should be disposed of in accordance with governmental regulations. Kino Flo, Inc. 2840 N. Hollywood Way, Burbank, CA 91505, USA Tel: 818 767-6528 website: www.kinoflo.