User's Manual

ManualsBrandsKINGTRACKER ManualsElectronicsKing Solutions 2G Tracker

USER Manual

1. Installation Manual

1.1 SIM Card Pre-installation

a. GSM SIM Only

b. SIM card should have its GPRS function enabled.

c. SMS request will function only if Caller ID function is enabled.

d. If SIM card is locked via PIN, please unlock SIM.

1.2 Turn on& turn off device & charging

1.2.1 Turn on device

a. Open the SIM card cover.

b. Insert SIM card into the SIM slot, metal face down.

c.Turn on the device by slide switch at the side of the device, the blue light and yellow light

glitter once, then yellow LED will on for few seconds when detecting signal, and then turns

off.

c. Call the device SIM number and it is supposed to get through without answer. (if you are

using a data SIM which is not supporting call function, ignore this step.)

d. Close the SIM cover after SIM installation

1.2.2 Turn off device

Turn off the device by slide switch at the side of the device

1.2.3 Charge the device

Connect the device with 5V power through USB port. The RED LED is steadily on during

charging and turns off when it is fully charged.

2. Operation Commands Guide

2.1 Set APN: (VERY IMPORTANT AND MUST BE DONE 1ST) For the device to send

data to the server, this command MUST be enabled.

SMS: *apn*AXXX*BXXX*CXXX* This command sets the telecom Access Point Name.

BXXX refers to user name, CXXX refers to password.

If there is no user name and password required, send as *apn*AXXX*

If there is user name but no password required, send as *apn*AXXX* BXXX*

APN information can be checked on local telecom website.

You will receive the following text: "Notice: APN is set to XXX. User name: XX. Password:

XX”

Summary of content (5 pages)

PAGE 1
USER Manual 1. Installation Manual 1.1 SIM Card Pre-installation a. GSM SIM Only b. SIM card should have its GPRS function enabled. c. SMS request will function only if Caller ID function is enabled. d. If SIM card is locked via PIN, please unlock SIM. 1.2 Turn on& turn off device & charging 1.2.1 Turn on device a. Open the SIM card cover. b. Insert SIM card into the SIM slot, metal face down. c.
PAGE 2
.2 Registering the “Master” Controller SMS to the device: *master*123456*+1XXXXXXXXXXXX*, (For instance, master controller phone number is +1XXXXXXXXXXXX. +1 refers to the country code. XXXXXXXXXXXX is the cellphone number. Please make sure country code is included, and digit 0 is not needed before cell phone number) Device Response: "Notice: Cell Phone # xxxxxxxxxx is set to master controller, the password is 123456.” (The device has a default password of “123456” to initially program in your PDA/Phone.
PAGE 3
4.1 SMS: *locateaddress* Master number will receive the Cell tower address of the device via SMS. 4.2 SMS: *locatemap* Master number will receive a Google map link. Click the link to view the map via cellphone browser. Device will reply the map link cell tower location. And this function is suitable for smart phone user only. 5. Status query SMS: *status* System Health and status check. Returns text message indicating various system diagnostics 6.
PAGE 4
Appoint low battery alert number SMS:*lowbat*alert cellphone number*Note: Please make sure country code is included in the cellphone number. Example *lowbat*+319876543210* 11.Device Information SMS: *about* You will receive a text message include software edition information and device’s serial number. 12. Command Setting List Function Command Description APN Setting *apn*AXXX*BXXX*CXXX* This command sets the telecom Access Point Name. BXXX refers to user name, CXXX refers to password.
PAGE 5
Function Command Description *multiquery* Enable multi controller function *multiqueryoff* End multi controller function Device Information *about* Software edition information and device’s serial number. Reboot 88888888 Reboot the system, previous settings will NOT be cleared. Master Query 999999 Registered master number information, password and device’s serial number. Low Battery Alert Number *lowbat*country code (plus) cellphone number* To set low battery alert number.