Owner's Manual Original Instructions Portable air conditioner Models: KPC05AK-A3NNA1C KPC05AK-A3NNA2C KPC05AK-A3NNA2B K KPC06AK-A3NNA1C KPC06AK-A3NNA2C KPC06AK-A3NNA2B KPC06AK-A3NNA3B K Thank you for choosing our product. Please read this Owner’s Manual carefully before operation and retain it for future reference.
Content Operation Notices Operation Environment ...........................................................................................1 Safety Warning ........................................................................................................2 Part's Name .............................................................................................................3 Operation Guide Operation Introduction for Control Panel .................................................................
Explanation of Symbols DANGER Indicates a hazardous situation that, if not avoided, will result in death or serious injury. WARNING Indicates a hazardous situation that, if not avoided, could result in death or serious injury. CAUTION Indicates a hazardous situation that, if not avoided, may result in minor or moderate injury. NOTICE Indicates important but not hazard-related information, used to indicate risk of property damage.
Operation Environment * The air conditioner must be operated within the temperature range: 61°F~95°F(16°C ~ 35°C). * The appliance is for indoor use only. * The appliance must be positioned so that the plug is accessible. * This air conditioner can only be used for family, not for commercial industry. * Reserved space around the air c " +/<= !> at least. * Do not operate the air conditioner at humid environment. * Please keep air inlet and air outlet clean, no obstacles.
Safety Warning * This appliance can be used by children aged from 8 years and above and persons with reduced physical,sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.Cleaning and user maintenance shall not be made by children without supervision.
Part's Name 1 2 3 1 Controller panel 2 Guide louver 3 Swing louver 4 Castor 5 6 Plug of power cord 7 Filter 8 Air inlet 9 Joint A 4 11 10 10 Heat discharge pipe 11 Joint B+C 7 9 8 6 5 Remote controller This picture is only for reference. Please refer to the actual product for the appearance. NOTICE: Heat discharge pipe and other installation accessories can't be discarded.
2SHUDWLRQ ,QWURGXFWLRQ IRU &RQWURO 3DQHO 1DPH RI FRQWURO SDQHO + / - button ual-8 nixie tube ool mode indicator ry mode indicator an mode indicator an speed indicator M button Sleep button Timer button ON/OFF button Fan button 2SHUDWLRQ RI FRQWURO SDQHO 1RWH * After putting through the power, the air conditioner will give out a sound. After that, you can operate the air conditioner by the control panel.
Operation Introduction for Control Panel 3 Mode button Press this button and the mode will circulate according to below sequence: QQ]^_R`^FAN COOL: L ! ! " & _ X Yie tube displays set temperature. Temperature setting range is 61°F(16°C)~X |V(30°C). _RY: L ! # ! " & _ X Y tube won’t display. FAN: Under this mode, the air conditioner only blow fan. Fan indicator is bright. _ X Y " % Z $ y.
Buttons on remote controller ON/OFF button 1 2 MODE button +/- button 3 4 5 FAN button X-FAN button 6 7 SLEEP button TIMER button Introduction for icons on display screen Timer on Timer off Sending signal X- cool operation dry operation fan operation Set temperature Set time x-fan operation sleep operation lock set speed
Introduction for buttons on remote controller Note: * When power is connected(stand by condition), you can operate the air conditioner through the remote controller. * When unit is on, each time you press the button on remote controller, the sending signal icon " " on the display of remote controller will blink once. If the air conditioner gives out a beep sound, it means the signal has been sent.
Introduction for buttons on remote controller Note: * L $ % ll $ $ $ ! # !" !$ & * V $ " _ # ! & 5 V " " # ! $ Y " l Y & Note: * Y % $ % $ % " %
Introduction for buttons on remote controller Note: * ! & \/ * The interval between two motions can't Y % ! troller will exit setting status. Function introduction for combination buttons Child lock function Press “+” and “-” buttons simultaneously can turn on or turn off child lock function. When child lock function is started up, LOCK indicator on remote controller is ON. If you operate the remote controller, remote controller won’t send signal.
Operation guide +& $ $ % $ Q QVV " ! & /& Q_ " # ! : QQ] _Y V & & " # !$ & =T !$ Z " ! >& & V " # $ % ! ! $ & Replacement of batteries in remote controller +& " !
Clean and Maintenance WARNING * Before cleaning the air conditioner, please turn off the unit and disconnect power. Otherwise, it may cause electric shock. * Do not wash air conditioner with water. Otherwise, it may cause electric shock. * Do not use volatile liquid (such as thinner or gas) to clean the air conditioner. Otherwise, it may damage the appearance of air conditioner.
&OHDQ DQG 0DLQWHQDQFH &OHDQ KHDW GLVFKDUJH SLSH Remove the ! "! pipe from air conditioner, clean and dry it , and then & =V ! ! $ instruction for "Installation and disassembly of heat discharge pipe"). &KHFNLQJ EHIRUH XVH VHDVRQ 1. Check whether air inlets and air outlets are blocked. 2. Check whether plug and socket are in good condition. & % & 4.
0DOIXQFWLRQ $QDO\VLV Please check below items before asking for maintenance. If the malfunction still Z " ! $ $ & Phenomenon Troubleshooting Solution * % * $ % #& * $ * $ & * % $ Air conditioner $ " can't operate * ! * $ $ replace air switch or fuse.
Malfunction analysis Phenomenon Troubleshooting Solution * * ! " & " * L ! % !$ !$ " % ! * ! $ % * hether evaporator is fros = " "# $ * $ % $ " % !$ & * $ r %
Malfunction analysis Malfunction code H8 Chassis is full of water. 1. Pour out the water inside chassis. 2. If "H8" still exits, please contact professional person to maintain the unit. F1 Malfunction of ambient temperature sensor. Please contact professional person to deal with it. F2 Malfunction of evaporator temperature sensor. Please contact professional person to deal with it. F0 1.Refrigerant is leaking 2.System is blocked 1.
Installation Precaution WARNING * Observe all governing codes and ordinances. * Do not use damaged or non-standard power cord. * Be caution during installation and maintenance. Prohibit incorrect operation to prevent electric shock, casualty and other accidents. Selection of installation location Basic requirement Installing the unit in the following places may cause malfunction. If it is unavoidable, please consult the local dealer: objects spread in the air. 2.
Preparation before installation Note: check if the accessories are available before installation. Accessory list joint A window panel drainage pipe joint B heat discharge pipe joint C Adapter wire hook pipe hoop sponge B rain shield pipe clip rubber plug nut support bolt spring washer washer remote controller battery (AAA 1.
Install Wire Hook * Assemble the wire hook at the back of the unit with screws (the direction of wire % $% wire hook screw direction of wire hook is downward * $ % % ook.
Removing Collected Water There are 2 ways to remove collected water: 1 Use the continuous drainage option from the bottom hole Note:When using the continuous drainage option from the bottom hole, install drainage pipe before using, otherwise poor drainage will affect normal operation of the unit. Instructions for drainage pipe installation as follows. 1. Remove the rubber plug at drainage port. drainage port 2.
Removing Collected Water _ % # % & 1. In cooling or drying operation, the condensation water will be drained to the chassis and spattered by water-striking motor. !$ ! % % " $ nd drained to outdoor. So usually, only a little condensation water will be accumulated inside the chassis and you do not need to disc % y.
Removing Collected Water 2 Use the continuous drainage option from the middle hole Note:Water can be automatically emptied into a floor drain by attaching 14mm inner diameter hose (not included). 1. Remove the continuous drain cap 1 by turning it counter clockwise then remove the rubber stopper 2 from the spout. 2. Screw the drain connector to(included in the package) the spout by turning clockwise. 3. Insert the drainage hose into drain connector.
Installation in a double-hung sash window (Note: If the inner width of window is below 20.5"(520mm), please remove the adjusting panel from window panel and then cut the window panel to make its width the same as the width of window.) cut adjusting panel window panel 1. Install rear clip — aim the rear clip(upper) at the rear clip(lower),fix them together, press the clasp forcibly in to the groove. rear connector (upper) clasp rear connector (lower) 2.
Installation in a double-hung sash window nut spring washer support washer bolt 5. Fix the rain shield on the support with nuts, spring washer, washer and bolt. screws washer nut rain shield spring washer 6. Cut the sponge B to a proper length and attach it to the window sash. sponge B (adhesive) 7. Attach the window panel to the window stool. 7.1 If the inner width of the window is less than 20.5"(520mm) The window panel cannot be installed in windows less than 20.5"(520mm) wide.
Installation in a double-hung sash window 7.2 If the inner width of the window is between 20.5"(520mm) and 37.4"(950mm) inclusive. (1) Open the window sash and place the window panel on the window stool. (2) Slide the adjustment panel to fit the window stool width. (3) Secure the window panel to the window stool with screws. Adjustment panel Screws Window panel assemble adjustment panel 20.5"~37.4" 7.3 If the inner width of the window is between 37.4" (950mm) and 56.7" (1440mm) inclusive.
Installation in a double-hung sash window 9. Close the window sash securely against the Window panel. 10. Cut the sponge A to a proper length and seal the gap between upper part of inner window sash and outer window sash. 11. Fix the inner window with window bracket and screw, so that it can not slide vertically. plastic window sponge A outer window window sash wooden window window bracket inner window Installation in a sliding sash window 1.
Installation in a sliding sash window window panel joint B+C inner side 3. Fix the protective grille on joint B+C with screws. screws protective grille 4. Fix the support on the outer side of window panel with nuts, spring washer, washer and bolt. washer Spring Washer Bolt Nut 5. Fix the rain shield on the support with nuts, spring washer, washer and bolt.
Installation in a sliding sash window 6. Cut the sponge B to a proper length and attach it to the window stool. sponge B (adhesive) 7. Install the window panel into the window stool. 7.1 If the heigth of the window is less than 20.5"(520mm). The window panel cannot be installed in windows less than 20.5"(520mm) high. (1) Remove the adjustment panel from the window panel, and cut the window panel to the same width as the window. (2) Open the window sash and place the window panel on the window stool.
Installation in a sliding sash window 7.3 If the inner width of the window is between 37.4" (950mm) and 56.7" (1440mm) inclusive. (1) Attach the extension panel to the adjustment panel. (2) Open the window sash and place the window panel on the window stool. (3) Slide the adjustment and extension panels to fit the window stool height. (4) Secure the window panel to the window stool with screws. Extension panel Screws adjustment panel 37.4"~56.7" Window panel assemble 8.
Installation in a sliding sash window 10. Cut the sponge A to a proper length and seal the gap between left side of inner window sash and outer window sash. 11. Fix the inner window with window bracket and screw, so that it can not slide horizontally.
Installation and Disassembly of Heat Discharge Pipe Install heat discharge pipe 1. Rotate joint A clockwise into the heat discharge pipe. heat discharge pipe Join A clockwise /. Install anather side of heat discharge pipe clockwise into protective grille sub-assy. Heat discharge pipe clockwise Join A 3. Insert joint A of heat discharge pipe (the side with "TOP" is upwards) into the groove until you hear a sound.
Installation and Disassembly of Heat Discharge Pipe Note of Installingheat discharge pipe The discharge pipe is suggested to be installed according to below figure by the manufacturer. under 51 inchs correct about 24 inchs User can adjust the installation method of the discharge pipe basing on the requirement, while the similar installation methods as below which will lead to unsmoothly air-out are not allowed. wrong * The length of the heat discharge pipe is less than 40 inchs.
Installation and Disassembly of Heat Discharge Pipe Disassemble heat discharge pipe 1. Remove joint A: Press the clasp and lift joint A upwards to remove it. 2. Remove heat discharge pipe from protective grille sub-assy. upwards joint A disassemble clasp Heat discharge pipe Anticlockwise Join A Operation Test * Put through the power supply and then press ON/OFF button on remote controller to start the unit.
Electric Schematic Diagram % + 、% 5220 7(03 78%( 7(03 6(1625 6(1625 57 / 、% 32:(5 %. %1 28778%( 7(03 5(&(,9(5 6(1625 %2$5' / :+ %8 $3 57 57 1 *1 <(*1 %8 * 5220 78%( 28778%( 5(& ',63 ',63 1 $& / $3 * &203 &203 0$,1 %2$5' ',63 (/(&75,& %2; . 5 0 & <(*1 &203 6 <(*1 ',63 $3 ',63/$< %2$5' <( 5' )$1 +,*+ :3 &$3 :+ %.
