User Guide

ManualsBrandsKING ManualsAccessories & SuppliesKING OA8300 Jack Replacement Head HDTV Directional Over-the-Air Antenna - White

STEP 1: Verify all components and parts are included.

STEP 2: Install the KING Jack Antenna in one of two ways (page 2):

• RV Mounting: Mount to a bat wing style retractable arm using the supplied RV Antenna Bracket.

• Pole Mounting: Mount to a stationary pole (on a house for example) using the supplied Pole Mount

Bracket. DO NOT MOUNT TO A POLE ON A VEHICLE.

STEP 3: READ THE FOLLOWING INFORMATION CAREFULLY, THEN CHOOSE A CONNECTION OPTION

ON PAGE 3 AND MAKE CONNECTIONS.

The KING Jack antenna is an amplied antenna that requires +12 volts power.

STEP 4: Read the OPERATING INSTRUCTIONS on page 4 for antenna pointing instructions.

Page 1

When using an existing power injector already in the RV

When replacing an existing amplied antenna that has an existing power injector, just replace

the antenna head assembly and verify that you have power to the KING Jack antenna when the

wall switch power injector is “ON.” A red LED light on the bottom of the KING Jack antenna will

illuminate when +12 volts is present and the internal amplier is powered. Do not use both the

existing power injector and the power injector supplied with the KING Jack Antenna!

Using two power injectors in the circuit can cause the KING Jack Antenna

power supply to overheat, possibly causing injury or severe damage.

Use either the existing power injector or the KING Jack power injector.

WARNING: DO NOT USE BOTH POWER INJECTORS!

A typical power injector for an

existing RV antenna will be a wall

plate or an A/V distribution box with

an ON/OFF type switch.

When using the KING Jack antenna with the supplied power injector

Verify that any existing power injector has been disconnected.

STEP 1

STEP 2

STEP 3

STEP 4

Model OA8300 Amplied HDTV Antenna

Output: 12V / 100mA

Input: 120V / 60Hz / 90 mA

Power Supply: AC/DC AdaptorReception Frequencies

VHF: 54-216 MHz

UHF: 470-698 MHz

FM: 87.9-107.9 MHz

Summary of content (4 pages)

PAGE 1
Model OA8300 Amplified HDTV Antenna STEP STEP 1: 1 Reception Frequencies Power Supply: AC/DC Adaptor VHF: 54-216 MHz UHF: 470-698 MHz FM: 87.9-107.9 MHz Input: 120V / 60Hz / 90 mA Output: 12V / 100mA Verify all components and parts are included. STEP 2: 2 Install the KING Jack Antenna in one of two ways (page 2): STEP • RV Mounting: Mount to a bat wing style retractable arm using the supplied RV Antenna Bracket.
PAGE 2
Option 1: BAT WING STYLE REPLACEMENT 1. Turn off antenna power injector at wall switch or A/V switch and raise the existing antenna. 2. Attach the RV antenna bracket to the KING Jack antenna with the 4 supplied screws. 3. Unscrew coax cable and remove existing bat wing style antenna (if present) from the retractable arm (keep retaining pins and clips). Line up holes in RV antenna bracket with holes in retractable arm and reinsert pins thru assembly.
PAGE 3
Page 3 NOTE: Illustration purposes only. Other configurations exist. IMPORTANT! Your RV may have more than one wall plate. Do not use the power injector supplied with the KING Jack antenna if an existing power injector is present.
PAGE 4
OPERATING INSTRUCTIONS: Scanning for Channels NOTE: In stationary applications, you only need to scan for channels one time. In mobile applications, you will need to scan for channels each time you change locations. 1. Turn on TV. 2. Turn on power to KING Jack antenna. NOTE: In steps 3-6, keep track of in which position you receive the most channels. 3. Perform a channel scan per the digital TV or digital TV converter box manufacturer’s instructions. 4. Rotate antenna 90 degrees.