Use and Care Manual
TECHNICAL DATA SHEET
This information is provided “as is” and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a technical service representative,
call 1-877-KILZ-PRO. ©2014 Masterchem Industries, 3135 Old Hwy M, Imperial, MO 63052-2834.
††
GREENGUARD is a registered trademark of UL Company
Revised 2/1/2016
1 of 1
INTERIOR / EXTERIOR WATER-BASE PRIMER
NO. 1300
PRODUCT INFORMATION
KILZ® PREMIUM Interior/Exterior Water-Base Primer is a superior quality, fast drying, primer, sealer and stainblocker that
provides excellent adhesion and a mildew resistant coating. It’s ideal for use in moisture prone areas and blocks out most
stains caused by water, tannin, ink, pencil, felt marker and grease. Topcoat with latex or oil-based paint.
RECOMMENDED USES:
Use on properly prepared interior and exterior surfaces, such as :
• Concrete • Concrete Block/CMU • Cement Board Siding • Brick • Stucco
• Plaster • Drywall/Gypsum Board • Wood • Plywood • Non-Ferrous Metals
• Architectural Plastics • Vinyl/PVC • Fiberglass
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 1300 128 oz. / 2 oz.
Resin Type: Acrylic Polymer
Weight per Gallon: 10.9 lbs.
% Solids by Volume: 41.6%
% Solids by Weight: 55.5%
VOC: <5 g/L
Flash Point: N/A
Viscosity: 95 - 105 KU
Recommended Film Thickness:
Wet: 5.3 mils / Dry: 2.2 mils @ 300 Sq. Ft./Gal.
Wet: 4.0 mils / Dry: 1.6 mils @ 400 Sq. Ft./Gal.
Coverage: 300 - 400 Sq. Ft./Gal. depending on the surface
texture, porosity and application method. Does not include
the loss of material from spraying.
APPLICATION:
Brush: Nylon / Polyester Blend
Roller: 3/8" - 3/4" nap
Airless Spray: Fluid pressure of 2,500 - 3,200 psi
Tip: .015" - .021"
Filter: 60 mesh
Thinning: Not recommended. Product is formulated for use
at package consistency only.
Dry Time: @ 77°F, 50% RH
Longer dry time required in cooler temperatures and in
higher humidity.
To Touch: 30 minutes
To Recoat: 1 hour
SURFACE PREPARATION:
The surface must be clean, free of dust, grease, wax, peeling
paint, mold, mildew and wallpaper paste. If washing is
necessary, use a non-soapy detergent or a TSP substitute.
Rinse well and allow to dry.
Peeling or Checked Paint: Scrape o loose paint and sand
to a smooth surface. Sanding or removal of paint containing
lead is hazardous. Unpainted, exterior wood exposed to sun
and/or moisture longer than 2-4 weeks must be cleaned and
sanded before priming.
Glossy Surfaces: For maximum adhesion, scu sand the
surface thoroughly before priming.
Masonry, Brick, Stucco and Plaster: KILZ PREMIUM
Interior/Exterior Water-Base Primer may be used on
clean, dry, aged masonry surfaces. New masonry must
be allowed to cure (dry) at least 30 days before applying
KILZ PREMIUM Interior/Exterior Water-Base Primer.
Fire Restoration: It is critical to clean smoke
damaged surfaces thoroughly before priming. Primary
Recommendation: KILZ COMPLETE®, KILZ ODORLESS® or
KILZ ORIGINAL Primers.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. Contact the National
Lead Information Center at 1-800-424-LEAD or visit
www.epa.gov/lead.
TEST SPECIFICATIONS:
Flexibility
ASTM D522 - Pass
Biological Growth
ASTM D3274 - Pass
CLEAN UP:
Clean all tools and equipment with clean water. For disposal
of empty containers and unused product, contact your
household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• For best results, apply at temperatures between 45°F -
90°F. Temperatures above 90°F may aect the application
such as drying too fast. Avoid painting in direct sun.
• Shelf life under normal conditions is two years unopened.
• Not for use on oors
GENERAL INFORMATION:
Warning! Causes eye and skin irritation. Wear protective
clothing, gloves, eye, and face protection. Do not eat, drink,
or smoke when using this product. Take o contaminated
clothing and wash it before reuse. Wash hands thoroughly
after handling. Dispose of unused contents, container and
other contaminated wastes in accordance with local, state,
federal and provincial regulations.
First aid: If in eyes: Rinse cautiously with water for several
minutes and remove contacts if present and easy to do.
Continue rinsing and get medical attention if eye irritation
persists. If on skin: Wash with plenty of soap and water.
If swallowed: Rinse mouth and get medical attention
if you feel unwell.
COMPLIES WITH THE BELOW AS OF 2/1/2016
SCAQMD YES LEED v.3 (2009)
†
YES
CARB YES LEED v.4
†
YES
OTC YES MPI 6, 39
LADCO YES GREENGUARD
† †
YES
AIM YES CHPS YES
†
Please visit www.usgbc.org/LEED for additional details.