Instruction Manual

ManualsBrandsKidztech Toys ManualsElectronicsR/C Fiery T-Rex (87414), R/C Dinoz (87411), R/C T-Rex (87415)

87415

PRO. SYSTEM

age

Battery installation

How to fill with water for smoking effect

Contents

RC T-Rex x 1

Water Pump x 1

Range

RC Transmitter x 1

15M / 49FT

Fig. 3

Transmitter

Fig. 4

3 x AA

For T-Rex

(Included for try-me)

2 x AA

For Transmitter

(Not Included)

T-Rex

Light, Sound

& Smoking

Effect

Forward

Movement

2.4 GHz

Signal Light

Transmitter - Battery Installation

Fig. 2

2.4G RADIO CONTROL T-REX

Instruction Manual

BATTERY REQUIREMENTS:

Battery Precaution

- RC T-Rex x 1

- RC Transmitter x 1

- Water Pump x 1

- Instruction Manual x 1

1. Alkaline batteries are recommend

2. Only batteries of the same or equivalent type as recommended are to be used

3. Do not mix alkaline, standard, or rechargeable batteries

4. Do not mix old and new batteries or different types of batteries

5. Non-rechargeable batteries are not to be charged

6. If rechargeable batteries are to be used, they are only to be charged under adult supervision

7. Rechargeable batteries are to be removed from the product before they are charged

8. Be sure to insert batteries with correct polarities and always follow the battery manufacturer’s instructions

9. Remove all batteries from the T-Rex and Transmitter when not in use

10. Exhausted batteries are to be removed from the product

11. The supply terminals are not to be short-circuited

12. Dispose of batteries properly / do not dispose the batteries in fire - it may cause them to explode or leak causing injury or damage

13. Battery installation and removal must only be done by an adult

For T-Rex (Fig. 1 and Fig. 2)

1. Switch the power button to OFF position

2. Unscrew the battery cover

3. Open the battery cover

4. Install 3 new 1.5V “AA” batteries with correct polarities (+/-)

5. Close the battery cover

6. Tighten the screw on the battery cover

For Transmitter (Fig. 3 and Fig. 4)

1. Unscrew the battery cover

2. Open the battery cover

3. Install 2 new 1.5V “AA” batteries with correct polarities (+/-)

as shown inside the battery compartment

4. Close the battery cover

5. Tighten the screw on the battery cover

Fig. 1

Fig. 5 Fig. 6

Fig. 7 Fig. 8

T-Rex

2. Open the water tank cap on the T-Rex. (Fig.6)

3. Squeeze the provided water pump to fill the water tank

into the T-Rex. (Fig.7)

4. Close the water tank cap firmly. (Fig.8)

USE

DISTILLED

WATER ONLY

NOT FOR

TAP WATER

1. Please prepare a cup of clear distilled water (not for

tap water). Keep squeezing and releasing the provided

water pump to fill up with the water. (Fig.5)

Summary of content (2 pages)

PAGE 1
87415 3 Instruction Manual 2.4G RADIO CONTROL T-REX PRO. SYSTEM Contents BATTERY REQUIREMENTS: 15M / 49FT Range 3 x AA - RC T-Rex x 1 For T-Rex (Included for try-me) - RC Transmitter x 1 - Water Pump x 1 - Instruction Manual x 1 2 x AA RC Transmitter x 1 RC T-Rex x 1 Water Pump x 1 For Transmitter (Not Included) Battery Precaution 1. Alkaline batteries are recommend 2. Only batteries of the same or equivalent type as recommended are to be used 3.
PAGE 2
87415 Trouble shooting for 2.4GHz pairing in case of no signal 1. Switch OFF the T-Rex and Switch ON to re-start. 2. Re-install batteries to the transmitter. 3. The transmitter signal light will flash for 7-8 seconds. 4. After the LED light of the transmitter stops flashing, the pairing process is complete for playing. 5. If pairing cannot be completed within 8 seconds, please turn off the T-Rex and re-start the pairing process. 6.