SUNVIEW II PLAY SYSTEM – F24061 INSTALLATION AND OPERATING INSTRUCTIONS WARNING To reduce the risk of serious injury or death, you must read and follow these instructions. Keep and refer to these instructions often and give them to any future owner of this play system. Manufacturer contact information provided below. 22’ 10’ 18’ 8” (5.7 m) 14’ 5” (4.4 m) OBSTACLE FREE SAFETY ZONE - 22’ x 24’5” (6.7 x 7.4 m) area requires Protective Surfacing. See page 3.
Warnings and Safe Play Instructions CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using this play system.
Protective Surfacing - Reducing Risk of Serious Head Injury From Falls. One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM F1292.
Instructions for Proper Maintenance Your Big Backyard Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is important that you, the owner, properly maintain it. Check the following at the beginning of the play season: HARDWARE: C heck metal parts for rust.
About Our Wood Solowave Design™ uses only premium playset lumber, ensuring the safest product for your children’s use. Although great care has been taken in selecting the best quality lumber available, wood is a product of nature and susceptible to weathering (changes in the aesthetics of the wood). A light sanding may be required to remove minor splinters. For your information, we have described some changes that may occur as a result of weathering: 1.
Keys to Assembly Success Tools Required Shovel Measuring Tape Drill (1/8” 3/16” Bit) Safety Glasses Part Identification Key On each page, you will find the parts and quantities required to complete the assembly step illustrated on that page. Here is a sample.
Wood Parts Identification (Reduced size) Actual Size Nominal Size 2 - Tarp Upright (2" x 3" x 47 3/4") 3660606 4 - Post (5/4" x 4" x 79") Nominal Size Actual Size 1" x 3 1/2" 1" x 6" 5/8" x 5 3/8" 5/4" x 4" 2" x 6" 1 3/8" x 5 3/8" 2" x 3" 2" x 4" 1 3/8" x 3 3/8" 1" x 5" 5/8" x 4-1/2" 2" x 2" 1 3/8" x 2 1/2" 1 1/2" x 1 1/2" 3660117 2 - Ground Side (1" x 5" x 78 3/4") 3660118 3 - Floor Support (5/4" x 4" x 39 1/2") 1 - SL Brace (2" x 3" x 15") 3660119 3660120 3 - CE Access Board (1" x 6
Wood Parts Identification (Reduced size) Nominal Size 1 - Roof Ridge (2" x 2" x 22-3/8") 3660106 4 - Ground Stake (2" x 2" x 14") 3650318 Actual Size 1" x 3 1/2" 5/8" x 5 3/8" 5/4" x 4" 2" x 6" 1 3/8" x 5 3/8" 2" x 3" 2" x 4" 1 3/8" x 3 3/8" 1" x 5" 5/8" x 4-1/2" 1 - Triangle Plate 3200182 (Pack of 2) 1 - Climbing Rocks with hardware 3320184 (Pack of 4) 1 - Slide 40" High Rail 3310140 1 - Sandy Summit Tarp and Frame 3750681 FRAME 2 - Belt Swings with Soft Touch Rope 3724933 8 Actual Size
Hardware Parts Identification (Actual Size) (64) Flat Head Screw #8 x 1-1/2" (9260512) (2) Pan Screw #8 x 1/2" (9264502) (14) Flat Head Screw #8 x 2-1/2" (9260522) (2) Pan Screw #12 x 2" (9264620) (7) Flat Head Screw #8 x 3" (9260530) (4) Hex Bolt 1/4 x 1-1/2" (9277212) 1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut (6) Hex Bolt 1/4 x 2" (9277220) 1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut (2) 1/4" x 3 1/2" Hex Bolt (9277232) 1/4" Lock Washer-1/4" Flat Washer- T-Nut (2) Hex Bolt 1/4 x 5-1/
Additional Parts List (Box 1): 1. Warning I.D. Plaque c/w hardware (3320356) STOP • FILL THIS OUT BEFORE YOU DISCARD YOUR CARTONS • THE CARTON I.D. STAMP IS LOCATED ON THE END OF EACH CARTON • YOU WILL NEED THIS INFORMATION IF YOU CALL CONSUMER RELATIONS DEPARTMENT PRODUCT NUMBER: F24061 CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 1) CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 2) CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 3) CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 4) CARTON I.D.
Step 1 Assemble Two Walls Using 1 Hex Bolt 5/16" x 4" (5/16" T-Nut, Washer and Lockwasher), attach loosely leaving a gap between the Tarp Upright (2" x 3" x 47 3/4") and 2 Posts (5/4" x 4" x 79"). Remember to use the proper assembly procedure for the Hex Bolt. Note: Do not tighten the Hex Bolt Repeat Step 1 for other side.
Step 2 Assemble Floor Supports Attach 4 T-Nuts 1/4" to the backs of the Floor Supports (5/4" x 4" x 39 1/2"). HARDWARE LIST Using 2 Wood Screws (#8 x 3") per side attach the SL Braces (2 x 3 x 15") to the Floor Supports (5/4" x 4" x 39 1/2").
Step 4 Attach Fort Walls and Tarp Upright Take previously assembled Floor Supports and attach to both Uprights of the previously assembled Walls using 2 Hex Bolts 1/4" x 3 1/2" (1/4" T-Nut, Flat Washer, and Lock Washer). Using 4 Hex Bolts 1/4" x 2" (1/4" Flat Washer, Lock Washer) attach the Floor Support (5/4" x 4" x 39 1/2") to the 4 Posts. 4 T-Nuts have been previously installed in Step 2. Using 2 Wood Screws (#8 x 3") attach the Roof Ridge (2" x 2" x 23-3/8") to the Tarp Uprights.
Step 5 Attach CE Access Boards, Floor Gussets HARDWARE LIST Hold the CE Access Boards against the 2 Posts so that the lower CE Access Boards are flush with the bottom of the Ground Sides, and the 20 pcs #8x1-1/2" Wood Screw upper CE Access Board is flush with top of the Floor Support. 2 pcs #8x2-1/2" Wood Screw Proceed to pre-drill with 1/8" drill bit, using the holes in the boards 2 pcs #8x3" Wood Screw as a guide.
Step 6 Assemble CE Floor and CE Rock Boards Hold the CE Rock Board against the 2 Posts. Make sure the CE Rock Boards are evenly spaced between the CE Access Boards, before proceeding to drill. Pre-drill with 1/8" drill bit using the holes in the boards as a guide. Follow the same procedure for the CE Floor Boards, making sure the CE Floor Boards are evenly spaced on the Floor Supports.
Step 7 Assemble Roof Using 2 Pan Bolts #8 x 3/8" and 2 #8 Lock Washers, connect 2 L -Frame Brackets (1/2" x 12 1/4" x 22 3/4") together. Make sure that the bolts go in from opposite directions, as shown in the diagram below. Repeat for the other side. Take one end of the Tarp and feed the L-Frame Bracket through the Tarp pocket. Repeat for the other side. With both L-Frame Brackets through the Tarp pockets, connect using 2 PanBolts #8 x 3/8" and 2 #8 Lock Washers for each side.
Post SW 5/4" x 4" x 81" T-NUT 5/16 x 4" Hex Bolt FLAT WASHER HEX BOLT LOCK WASHER REMEMBER TO USE THIS ASSEMBLY PROCEDURE FOR HEX BOLTS SW Post 2" x 4" x 80-1/2" Post SW 5/4" x 4" x 81" 1/4 x 2" Hex Bolt NOTE! Do not tighten the Hex Bolt until after the Floor Support is attached Using 2 Wood Screws (#8 x 2-1/2") attach 1 SW Block (5/4" x 4" x 3 1/2") to bottom of the SW Post. Refer to the diagram below.
Swing Hanger CE SW Rail Tighten Hanger in until it is tight and flush with bottom of Swing Beam Swing Hanger orientation for Swing Hanger Follow Proper Assembly Procedure Bolt Hangers must be ! Warning! tightly installed to CE SW Rail.
Incorrect Correct SW Post Triangle Plate 5/16" x 3" Hex Bolt 1 pc 5/16x3" Hex Bolt 1 pc 5/16x1-1/2" Hex Bolt 2 pcs 5/16" T-Nut 2 pcs 5/16" Flat Washer 2 pcs 5/16" Lock Washer 1 pc #8x2-1/2" Wood Screw HARDWARE LIST T-NUT FLAT WASHER HEX BOLT LOCK WASHER REMEMBER TO USE THIS ASSEMBLY PROCEDURE FOR HEX BOLTS 5/16" x 1 1/2" Hex Bolt 110° #8 x 2 1/2" Wood Screw CE SW Rail NOTE: Remember to use the proper assembly procedure for the Hex Bolts. Do not over-tighten Hex Bolts.
#8 x 2 1/2" Wood Screw INCORRECT CORRECT 5/16" x 1 1/2" Hex Bolt 5/16" x 3" Hex Bolt 5/16" x 1 1/2" Hex Bolt Notice: Canopy has been removed for clarity. Do not remove. Note: Tighten all Hex Bolts from previous steps. A 6 foot safety clearance must remain around the fort prior to use. T-NUT FLAT WASHER HEX BOLT LOCK WASHER REMEMBER TO USE THIS ASSEMBLY PROCEDURE FOR HEX BOLTS NOTE: An adult helper may be required for this step.
Ground Stakes must be driven a minimum of 10½" into ground before attaching to post. Ground Stake 2" x 2" x 14" #8 x 2-1/2" Wood Screw SW Post Ground Stake Location #1 SW Post Hole Dig 2" Deep #12 x 2" Pan Screw Ground Stake Location #4 SL Brace Ground Stake Location #2 MAKE SURE GROUND AND FORT ARE LEVEL PRIOR TO DIGGING AND STAKE DRIVING. Using 2 Pan Screws (#12 x 2"), attach Slide making sure that screws go through the Floor Board and into the SL Brace .
#8 x 1" Pan Screw 1/4" Barrel Nut Rock Board 4 pcs Rocks with hardware 2 pcs Swings 4 pcs Hole Plugs ACCESSORY LIST * PERIODICALLY CHECK AND RE-TIGHTEN ALL HEX BOLTS, LAG SCREWS, AND WOOD SCREWSTO ENSURE SAFETY. DO NOT OVER TIGHTEN TO AVOID CRUSHING WOOD. *THOROUGHLY READ INSTRUCTIONS AND THE OWNERS MANUAL BEFORE USING PLAY CENTRE . *KEEP ASSEMBLY INSTRUCTIONS FOR FUTURE REFERENCE .
Final Step: Attach I.D. Plaque ATTACH THIS WARNING & I.D. PLAQUE TO A PROMINENT LOCATION ON YOUR PLAY EQUIPMENT! (Fort or Swing Post) This provides warnings concerning safety and important contact information. A Tracking Number is provided to allow you to get critical information or order replacement parts for this specific model.
NOTES
NOTES
NOTES
BIG BACKYARD Consumer Registration Card First Name Initial Last Name Street Apt. No.