Owner’s Manual Manual del Propietario Manuel d’utilisation Benutzerhandbuch KICKER PowerBar KPB1 | KPB2 Amplified Weatherproof Bar-Mount Speaker System with Bluetooth Sistema de alto-falantes Amplificado à prova de intempéries com Bluetooth Système d’enceintes Amplifiées étanches à Montage sur Barre avec Bluetooth Verstärktes Wetterfestes Bar-Mount-Lautsprechersystem mit Bluetooth select language seleccione el idioma choisir la langue sprache auswählen
Contents Overview......................... 2 Specifications......................... 3 Installation....................... 4 Wiring.................................... 4 Mounting................................ 5 Operation........................ 7 Status LED............................. 7 Control Panel......................... 8 Setting Input Source............... 9 Broadcast Mode.................... 9 Remote Control Install........... 10 Remote Control Operation.... 10 Troubleshooting.............
Overview IMPORTANT SAFETY WARNING PROLONGED CONTINUOUS OPERATION OF AN AMPLIFIER, SPEAKER, OR SUBWOOFER IN A DISTORTED, CLIPPED OR OVER-POWERED MANNER CAN CAUSE YOUR AUDIO SYSTEM TO OVERHEAT, POSSIBLY CATCHING FIRE AND RESULTING IN SERIOUS DAMAGE TO YOUR COMPONENTS AND/OR VEHICLE. AMPLIFIERS REQUIRE UP TO 4 INCHES (10CM) OPEN VENTILATION. SUBWOOFERS SHOULD BE MOUNTED WITH AT LEAST 1 INCH (2.5CM) CLEARANCE BETWEEN THE FRONT OF THE SPEAKER AND ANY SURFACE.
Specifications Model: Power Output @ 14.4V, <10% THD+N KPB1 KPB2 150W 300W Woofer [in, mm] 3, 76 Tweeter [in, mm] 1, 25 Wiring Harness Length [ft, m] 10, 3.05 Frequency Response [Hz] 50-20,000 Signal-to-Noise Ratio Tweeter Magnet Material Tweeter Dome Material Tweeter Design Woofer Cone Material Woofer Surround Material >75, A-weighted re: rated power Neodymium Titanium Dome Polypropolene Santoprene Aux Input Stereo 3.5mm Female 0–1.75 V Sensitivity RCA Output Stereo 3.
Installation Wiring Disconnect the vehicle’s battery to avoid an electrical short. Connect the KPB’s black ground wire to a paint-and-corrosion-free, solid, metal area of the vehicle’s chassis, or to the negative battery terminal. Connect the KPB’s red power wire to the positive battery terminal. Install a 15A fuse for the KPB1 or 30A fuse for the KPB2 between the KPB and the power source.
Keep the audio signal cable away from factory wiring harnesses and other power wiring. If you need to cross this wiring, cross it at a 90-degree angle. Mounting The KPB-series mounts natively to bar cylinders with included bar clamp diameter sizes of 1.5”, 1.75”, and 2”. Use the KPB Square Clamps (LINK GOES HERE) - sold separately - to mount your KPB to square bars. Choose a structurally sound location to mount the KPB. The KPB may be mounted below or above bars.
2. Place the Clamp Rings around your mounting bar and secure the Clamp Rings to the Mounting Bases using the Clamp Screws.
Operation Status LED LED color displays audio source, pairing status, and warnings: Flashing Blue - in pairing mode Solid Blue - connected bluetooth device Red - 1/8” (3.
Control Panel short press 1S long press EQ 10S very long press Power on the KPB by performing a long press of the POWER Button Long Press - Power On/Off Increase Volume Decrease Volume Short Press - Previous Track Long Press - Rewind Short Press - Next Track Long Press - Fast Forward Short Press - Play/Pause or Mute Very Long Press (10s) - Software Reset Short Press - Change Input Source Long Press - Enter Bluetooth Pairing Mode EQ English Change EQ Presets - KICKER, LOUD, SOUND QUALITY, & VOICE
Setting Input Source Short Press the SOURCE button to switch between Bluetooth (blue) and AUX IN (red) input sources. To enter Bluetooth Pairing Mode, Long Press the SOURCE button while in Bluetooth mode. The STATUS LED will begin to flash blue. You may exit pairing mode at this stage by short pressing the SOURCE button. To finish pairing, from your audio device select either ‘KPB1 KICKER’ or ‘KPB2 KICKER’. When successfully connected, the STATUS LED will be solid blue.
Remote Control Install The remote control must be charged via USB micro 5V power input. Install the included remote control to your steering wheel as follows: 1. Place the KPB onto the wheel facing the user in the position in which it will be most used. 2. With the lock open, place the two arms of the remote control around the steering wheel. 3. Pull the lock down over the open slot on the adjacent arm.
Troubleshooting If the KPB becomes frozen or stuck during algorithmic calculation, does not appear to be working, or gives an error code, check the obvious things first such as blown fuses, poor or incorrect wiring connections, incorrect setting of gain controls, etc. No power? With a Volt Ohm Meter (VOM) check the following: +12 volt power terminal (should read +12V to +16V) Check for reversed power and ground connections Ground terminal, for proper conductivity.
Warranty When purchased from an Authorized KICKER Dealer, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase with receipt. If this product is identified as “Refurbished” or “B Goods”, the warranty is limited to a period of THREE (3) MONTHS from the date of original purchase. In all cases you must have the original receipt.
The RMA number must be clearly marked on the outside of the package. Please return only defective components. The return of functioning items increases your return freight charges. Nondefective items will be returned freightcollect to you. For example, if a subwoofer is defective, only return the defective subwoofer, not the entire enclosure.
FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.