User's Manual

ManualsBrandsKeyence ManualsComputers & AccessoriesHandheld Mobile Computer

E BT-W80GA/W85GA-IM

Handheld Mobile Computer

BT-W80GA/W85GA

Instruction Manual

Read this instruction manual before using the product in order to achieve maximum

performance. Keep this instruction manual in a safe place after reading it so that it can be

used at any time.

In this instruction manual, the BT-W80GA Series means the BT-W80GA and BT-W85GA.



Symbols

The following symbols alert you to important messages. Be sure to read these messages

carefully.

• IEEE802.11a/b/g/n: Wireless LAN standards established by 802 committee which has

designed standards of LAN technology in IEEE (Institute of Electrical and Electronics

Engineers).

• Bluetooth

wordmark and logo belong to Bluetooth SIG, Inc. and KEYENCE uses them

under license. Other trademarks or trade names belong to each owner.

•microSD

is a trademark of SD Card Association.

• Microsoft, Windows, Internet Explorer and Visual Studio are registered trademarks or trademarks

of Microsoft Corporation in the United States and other countries.

• The official name for Windows is "Windows

operating system".

• ARM Cortex is a trademark and registered trademark of ARM Limited in EU and other

countries.

• Other company names or product names described in this manual are registered

trademarks or trademarks of each company.

• It is prohibited to use or copy all or any part of this manual without prior approval.

• The information contained in this manual is subject to change without notice.



General cautions

This product employs a semiconductor laser for its light source.

* The laser classification for FDA(CDRH) is implemented based on IEC60825-1 in

accordance with the requirements of Laser Notice No.50.

Follow the instructions mentioned in this manual. Otherwise, injury to the human body

(eyes and skin) may result.

Locations of warning / explanation labels

Introduction

It indicates a hazardous situation which, if not avoided, will result in

death or serious injury.

It indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

It indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

It indicates a situation which, if not avoided, could result in product

damage as well as property damage.

It indicates cautions and limitations that must be followed during

operation.

It indicates additional information on proper operation.

It indicates tips for better understanding or useful information.

Safety Information for the BT-W80GA Series

• Do not use this product for the purpose of protecting a human body

or a part of human body.

• This product is not intended for use as an explosion-proof product.

Do not use this product in a hazardous location and/or potentially

explosive atmosphere.

• Suffocation may result from wrapping the lanyard around the neck. Be

careful to use BT-W80GA around a power-driven machine on work.

• Verify that this device is operating normally in terms of functionality

and performance before the start of work and when operating the

device.

• We recommend that you take substantial safety measures to avoid

any damage in the event that a problem occurs.

• If the equipment is used in a manner not specified by the

manufacturer, the protection provided by the equipment may be

impaired.

• Do not throw, drop or trample down the BT-W80GA Series and

accessories to strong physical shock.

• Keep BT-W80GA Series or accessories out of the reach of children.

Children may swallow batteries, batteries attachment covers and

straps around themselves.

• When the BT-W80GA Series is used in combination with other

instruments, functions and performance may be degraded, depending

on operating conditions and the surrounding environment.

• The LCD panel may generate microscopic spots (black/bright spot),

uneven brightness or crosstalk (phenomenon that non-existent lines

or patterns are displayed), depending on the conditions.

• If the same display remains on the screen for a long time, afterimage

may occur due to the characteristics of LCD.

DANGER

WARNING

CAUTION

NOTICE

Important

Point

Reference

DANGER

CAUTION

NOTICE

Safety Precautions on Laser Product

Item

BT-W80GA

BT-W85GA

Wavelength 655 nm 655 nm

Output 1.0 mW 390 ¦W

Laser Class

Class 2 laser product

(IEC60825-1,

FDA(CDRH) Part 1040.10*)

Class 1 laser product

(IEC60825-1,

FDA(CDRH) Part 1040.10*)

Use of controls or adjustments or performance of procedures other

than those specified herein may result in hazardous radiation

exposure.

• Do not disassemble this product. Laser emission from this product

is not automatically stopped when it is disassembled.

Class 1 Laser Product

• Do not stare into the direct or specularly reflected beam.

Class 2 Laser Product

• Do not stare into the direct or specularly reflected beam.

• Do not direct the beam at other people or into areas where other

people unconnected with the laser work might be present.

• Be careful of the path of the laser beam. If there is a possibility that

the operator may be exposed to the specular or diffuse reflections,

block the beam by installing a protective enclosure.

• Install this product so that the path of the laser beam is not as the

same height as that of human eye.

Safety Precautions on LED Product

• Use of controls or adjustments or performance of procedures other

than those specified herein may result in hazardous radiation

exposure.

• Follow the instructions mentioned in this manual. Otherwise, injury

to the human body (eyes and skin) may result.

• Do not stare into the beam.

• Do not disassemble this product.

LED emission from this product is not automatically stopped when

it is disassembled.

• Do not view directly with optical instruments. Viewing the LED

output with certain optical instruments (for example, eye loupes,

magnifiers and microscopes) within a distance of 100 mm may

pose an eye hazard.

WARNING

CAUTION

BT-W80GA

Scanner

(Laser emission part)

BT-W85GA

Scanner

(Laser emission part)

96M13983

Summary of content (6 pages)

PAGE 1
Safety Precautions on Laser Product 96M13983 This product employs a semiconductor laser for its light source. Handheld Mobile Computer BT-W80GA/W85GA Item BT-W80GA Wavelength 655 nm 655 nm Output 1.0 mW 390 ¦W Laser Class Class 2 laser product (IEC60825-1, FDA(CDRH) Part 1040.10*) Class 1 laser product (IEC60825-1, FDA(CDRH) Part 1040.10*) * The laser classification for FDA(CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice No.50.
PAGE 2
IC Regulations Precautions on Proper Use The BT-W80GA Series complies with the following regulations specified by the IC. • Applicable regulation ICES-003 RSS-247 • The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used.
PAGE 3
Precautions on wireless LAN and Bluetooth Precautions for proper use • Remove the main battery of the BT-W80GA Series near locations where using wireless devices is banned at medical institutions or near electric devices for medical purposes. Carry and use the product away from an implanted cardiac pacemaker. WARNING • The BT-W80GA Series uses the radio wave of 5GHz band, and can 5.2GHz band (W52), 5.3GHz band (W53), 5.6GHz band (W56) and 5.8GHz band (W58). Using 5.2GHz band (W52) and 5.
PAGE 4
Cleaning Specifications Clean the following parts with air blow periodically. If removing dirt is difficult, use a cotton swab to clean the contacts directly. (Use absolute ethanol if dirt is stuck on them.) Remove the battery attachment cover before cleaning the battery contact.
PAGE 5
Item Drop resistance Environment resis- Operation temperature tance Operation humidity Storage temperature Storage humidity Dimensions () shows grip parts. Weight with battery pack Accessory Outline dimensional drawing Specifications Enclosure sealing IP64 (IEC60529) Multiple drops to concrete: 3.0 m*3 BT-W80GA Multiple drops to concrete: 2.5 m*3 63 -5 to +50 °C (No freezing)*4 -20 37.7 61.6 20 to 85%RH (No condensation) -20 to +60 °C (No freezing) 20 to 85%RH (No condensation) 173 x 61.
PAGE 6
WARRANTIES AND DISCLAIMERS (1) KEYENCE warrants the Products to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment. If any models or samples were shown to Buyer, such models or samples were used merely to illustrate the general type and quality of the Products and not to represent that the Products would necessarily conform to said models or samples.