Wireless Hand-held Barcode Reader BL-N90 Series User's Manual Read this manual before using the system in order to achieve maximum performance. Keep this manual in a safe place after reading it so that it can be used at any time.
Introduction This manual contains information about procedures for handling, operations, warnings, and precautions about the "Wireless Hand-held Barcode Reader BL-N90 Series". Be sure to read this section thoroughly before use. Keep this manual in a safe place for future reference. b Symbols The following symbols and conventions alert you to important messages. Be sure to read these messages carefully.
Safety Precautions b Safety Precautions on Laser Products The "Wireless Hand-held Barcode Reader BL-N90 Series" employs a visible light semiconductor laser for its light source.The BL-N90 Series is classified as a Class 1 laser under IEC standards (IEC 60825-1: "Safety of Laser Products"). WARNING Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Handling the BL-N90 Series • When recharging the BL-N90/N90K with BL-N9R, BL-N9UB, or BL-N9V, make sure to check whether foreign materials have entered the charging terminal.The presence of foreign materials may generate high heat or ignition, which may cause fires. • Check whether dust covers the power plug of the AC adapter that connects to WARNING BL-N9R, BL-N9UB, or BL-N9V, and clean it regularly.There is a danger that a fire will start due to tracking.
Wireless Communication The BL-N90 Series contains an internal wireless function based on Bluetooth wireless technology. CAUTION Disassembly or modification of the BL-N90 Series is prohibited under the Japanese Electrical Appliance and Material Safety Law (DENAN). Do NOT disassemble or modify the product.
Precautions on Safety Standards Europe b Precautions on CE Marking The BL-N90 series complies with the R&TTE Directive. • Applicable standard ESTI EN300 328 V1.6.1 • Overvoltage category • Pollution degree ESTI EN301 489-17 V1.2.1 EN60950-1 EN60825-1, Laser Class1 I (BL-N90/N90K) II (BL-N9R/N9UB/N9V) 2 b Countries where the BL-N90 Series can be used Among the EU member states, the BL-N90 Series can be used in the following countries.
North America b Precautions on FCC The BL-N90 Series complies with the following FCC requirements. • Approved standard FCC Part 15 Subpart B, Class B Digital Device • FCC ID FCC Part 15 Subpart C RF40823A (BL-N90/N90K) RF40823B (BL-N9R/N9UB/N9V) FCC WARNING Changes or modifications not expressly apprvoed by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules and RSS-Gen of the IC Rules.
Maintenance Clean the following parts on the BL-N90/N90K and the communication unit periodically. • BL-N90/N90K Clean the laser emitter/receiver and the charging terminals. Charging terminals Laser emitter/ receiver • Communication unit Clean the charging terminals. Charging terminals b Cleaning method Laser emitter/receiver : Clean the surface using an eyeglass cleaning cloth or a soft cloth that has been dampened with a specialty cleaner for plastics.
1 1 Overview Overview This chapter describes names and functions of each part of the items in the package. 1-1 Checking the Package Contents . . . . . . . . . . . 1-2 1-2 Part Names. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1 Checking the Package Contents The BL-N90/N90K series comes with the following items. Check that all of the items are included. 1 Wireless Hand-held Barcode Reader BL-N90/N90K Overview b BL-N90/N90K barcode reader: 1 b Strap: 1 b AC cable: 1 Supplies power by using the AC adapter of the communication unit. * This cable is not included in the BL-N90K. Please prepare one separately. * This cable can be used in Japan only.
1-1 Checking the Package Contents Communication Unit BL-N9R/N9V/N9UB The following models are available for each communication interface: Model Communication interface BL-N9R RS-232C communication unit BL-N9V Keyboard interface communication unit BL-N9UB USB communication unit 1 Overview b Communication unit: 1 BL-N9R BL-N9V BL-N9UB b AC adapter: 1 b Wall mount screw: 2 Used to mount the communication unit on a wall.
1-1 Checking the Package Contents Option b Stand OP-82191 Used to fix the BL-N90/N90K on a desktop to read barcodes by bringing them close to it.
1-2 Part Names This chapter describes names and jobs of each part of the BL-N90/N90K Series. b BL-N90/N90K 1 Trigger switch: Use the switch to read a barcode. White operation check LED Blue operation check LED Charging terminals Emitter/receiver: Emits and receives laser light. b Communication unit BD address barcode: Read this barcode for establishing connection (pairing) with the BL-N90/N90K.
1-2 Part Names Operation check LEDs The LEDs illuminate or flash for each operation as shown in the following table. A beep may sound at the same time for some operations. 1 b BL-N90/N90K LED lighting/flashing BL-N90/N90K status Beep* Overview Lights in blue Flashes in blue Emitting laser. – • Not wirelessly connected with the communication unit. • Out of the wireless communication range. – Wireless communication is cut. 2 Sending data to the communication unit.
2 First Steps 2 First Steps This chapter describes the procedures for connecting the BL-N90/N90K to use for the first time. 2-1 The Setup Procedure . . . . . . . . . . . . . . . . . . . . 2-2 2-2 Connecting the Power Cable to the 2-3 Connecting the Communication Unit . . . . . . . 2-5 2-4 Charging the BL-N90/N90K. . . . . . . . . . . . . . . 2-11 2-5 Establishing a Connection . . . . . . . . . . . . . . . . 2-13 2-6 Initial Setup for the BL-N90/N90K . . . . . . . . .
2-1 The Setup Procedure Before using the BL-N90/N90K, the following connections must be set up. Performing these connections establishes the following communications, enabling the BLN90/N90K for use. • Communication unit to PC connection: Wired transmission • BL-N90/N90K to communication unit connection: Wireless transmission (Bluetooth) 2 Note After connecting the communication unit to the computer, be sure to charge the BL-N90/N90K before use.
2-2 Connecting the Power Cable to the Communication Unit Connect the power cable to the communication unit before use. b Included parts • AC cable for the BL-N90 (The AC cable for the BL-N90K is not included. Please prepare one separately.) • Communication unit • AC adaptor for the communication unit 2 Procedure First Steps 1 Connect the AC cable to the AC adaptor.
2-2 Connecting the Power Cable to the Communication Unit 2 Connect the AC adapter to the AC connector on the back of the communication unit. After connecting the AC adaptor, snap the cable behind the hook.
2-3 Connecting the Communication Unit After connecting the power cable to the communication unit, connect the communication unit to your computer using the interface provided. Connecting the BL-N9UB to your Computer Use the USB cable to connect the communication unit to your computer. The barcode reader is compatible with Windows XP/2000/98. 2 Procedure First Steps 1 Turn on your computer. 2 Connect the communication unit's interface cable to the USB port on your computer.
2-3 Connecting the Communication Unit Installing the USB Driver When BL-N9UB is first connected to a computer running Windows 98, the USB driver installation screen appears. Install the driver by following the directions given on the screen. (This procedure is not necessary when using a computer running Windows XP/2000). Note 2 Connect the barcode reader after turning on the computer. If the barcode reader is connected with the power off, turn the computer on.
2-3 Connecting the Communication Unit Connecting the BL-N9V to your Computer Use the keyboard interface to connect the communication unit to your computer. Compatible computers include PC/AT (DOS/V) machines. Procedure 1 Turn off the computer. CAUTION 2 Do not remove the cables while the computer is turned on. This could cause damage to the computer and the barcode reader. as indicated in the diagram.
2-3 Connecting the Communication Unit 3 Connect the power cable to an AC outlet, and turn on the communication unit. The blue LED on the communication unit will flash. 2 CAUTION • Be sure to use the AC adaptor provided with the device. Connecting to other power sources may cause electric shock, fire or product damage. First Steps 4 Turn on your computer.
2-3 Connecting the Communication Unit Connecting the BL-N9R to your Computer A communication unit with an RS-232C interface may be used in conjunction with an RS232C enabled device. This section explains procedures for connecting the barcode reader to a computer, as well as connecting the barcode reader to an AutoID data controller DV-90 ( page 2-10). Procedure BL-N9R Computer RS-232C (D-sub 9-pin) 3 Connect the power cable to an AC outlet, and turn on the communication unit.
2-3 Connecting the Communication Unit b Communication settings Factory settings for the BL-N90 are given below. The settings can be changed. Make sure that the settings for BL-N90/N90K and the connected computer are the same. 2 • Baud rate : 9600 bit/s • Data length : 7 bits • Parity : Even • Stop bit : 1 bit • Communication protocol: No protocol First Steps Connecting the DV-90 To connect the device to a DV-90, an adaptor like the diagram below is required.
2-4 Charging the BL-N90/N90K The communication unit is used to charge the BL-N90/N90K. The barcode reader is shipped with zero charge. Please charge the device before use. Note The barcode reader may be used to scan ( minutes. page 2-13) after a charge of just 10 2 b How to charge Procedure First Steps 1 Connect the communication unit to your computer using the appropriate connection method, and make sure both sides are powered on.
2-4 Charging the BL-N90/N90K Rechargeable Batteries for the BL-N90/N90K The BL-N90/N90K sounds an alarm when the battery is low. When using the scanner, be mindful of the alarm and always maintain a charge. b Battery low alarm When the BL-N90/N90K battery level gets low, the following alarms are sounded.
2-5 Establishing a Connection The BL-N90/N90K and the communication unit communicate as a pair. This section describes how to establish a connection between the BL-N90/N90K and the communication unit. Note Perform the following operation with the communication unit connected to your computer ( page 2-5). 2 Procedure First Steps The following symptoms indicate that a connection is not established.
2-5 Establishing a Connection Notes About Establishing a Connection Between the Scanner and the Communication Unit b Reading a barcode The BL-N90/N90K cannot read a barcode unless a connection has been established with the communication unit. (A beep will sound twice.) 2 b Using multiple BL-N90/N90K barcode readers First Steps • Only the connected barcode reader and communication unit pair can communicate with one another.
2-6 Initial Setup for the BL-N90/N90K After establishing a connection between the BL-N90/N90K and the communication unit, be sure to initialize its configuration. This ensures that the scanner's configuration is initialized to match the interface type of the communication unit. Procedure Once scanning of the "Initialization" barcode is complete, a beep will sound 3 times. 2-15 2 First Steps 1 Press the "Trigger" switch to activate the laser.
2-7 Reading a Barcode This section describes the basic barcode scanning operations. Scanning a Barcode The BL-N90/N90K is able to read barcodes when it is connected wirelessly to the communication unit. The wireless connection can be verified by checking that the blue LED on the communication unit is lit ( page 1-6). 2 1 Press the "Trigger" switch to activate the laser. First Steps As the laser is activated, the blue LED on the BL-N90/N90K lights up . 2 Aim the laser to cover the entire barcode.
2-7 Reading a Barcode b Precautions for reading • If the BL-N90/N90K communicate with the communication unit wirelessly, then the barcode will not be read. (A low-pitched beep will sound twice.) • Be sure to aim the laser to scan the entire length of the barcode. × Incorrect scan { Correct scan 2 × Incorrect scan • Depending on the laser reflection, interior lighting, or barcode label angle, light reflected from the label may be partially reflected, resulting in scan errors.
2-8 Wireless Connection Environment The BL-N90/N90K and the communication unit use Bluetooth Version 1.2 for their wireless communication. Please use in the following environment. b Transmission range and surrounding conditions 2 The BL-N90/N90K and the communication unit have a line-of-sight range of approximately 10 meters. However, obstacles placed between the BL-N90/N90K and the communication unit, such as concrete or metal, may interrupt the wireless connection.
Appendices This chapter describes the specifications and outer dimensions. A-1 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . .A-2 A-2 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-1 Specifications b BL-N90/N90K Model BL-N90/N90K Light source Visible semiconductor laser (Wavelength: 650 nm) Maximum output 350 µW Pulse width 1.5 ms Class Scan rate Class 1 (IEC 68025-1) 72 scans per second Minimum resolution 0.127 mm Reading distance 25 to 250 mm (Narrow bar width: 0.5 mm) 0 to 165mm (Narrow bar width: 0.25mm) PCS 0.
A-1 Specifications b Communication unit Model Wired communication unit Wireless communication unit Charger Environmental condition BL-N9R BL-N9V BL-N9UB RS-232C Keyboard Interface USB-HID Ver1.1 *1 Connector shape D-Sub 9-pin (female) Mini DIN 6-pin USB (A type) Wireless standard Bluetooth Ver1.2 Wireless frequency 2.4 GHz Transmission output Class 2 (2.5 mW max.
A-2 Dimensions b BL-N90/N90K (units: mm) 77 60.
Introduction This manual contains information about procedures for handling, operations, warnings, and precautions about the "Wireless Hand-held Barcode Reader BL-N90 Series". Be sure to read this section thoroughly before use. Keep this manual in a safe place for future reference. b Symbols The following symbols and conventions alert you to important messages. Be sure to read these messages carefully.
Wireless Hand-held Barcode Reader BL-N90 Series User's Manual Read this manual before using the system in order to achieve maximum performance. Keep this manual in a safe place after reading it so that it can be used at any time.