User's Manual

ManualsBrandsKey Mouse Electronic ManualsComputers & AccessoriesRF Mouse

RF Keyboard & Mouse User Manual

PRODUCT LIST

When you have opened the package, please make sure that all accessories are included as below:

 Wireless Keyboard ×1

 Wireless Mouse ×1

 Receiver ×1

 Driver Disk ×1

 User’s instructional Guide ×1

 Alkaline Batteries of size AA ×3 (for keyboard)

 Ni-MH Batteries of size AAA ×2 (for Mouse)

In case of missing or damage of the above accessories, please contact your purchased dealer immediately.

BATTERY INSTALLATION

Open the battery cap , which is on keyboard’s or mouse’s reverse side , place batteries, and put the cap back.

Every time after having changed batteries , please reset up mouse ,or keyboard, or mouse and keyboard

depending on which unit you have changed batteries. For re-setup , please follow the setup of “SETUP FOR

USE “.

HARDWARE INSTALLATION

Shut down your computer system.

Connect the green connector of the receiver to the PS2 connection port of the computer , or connect the purple

connector of the receiver to the PS2 connection port，or connect the black USB connector of the receiver to the

USB connection port on the computer.

Turn on your computer system.

SOFTWARE INSTALLATION (DRIVER)

Insert the CD/Driver into CD-ROM.

The computer will into the setup up screen .

Select “KEYBOARD + MOUSE 2 IN 1”

Click on the appropriate item to setup.

Follow the setups indicated in the screen to complete the setup.

SETUP FOR USE

1. MOUSE

1.1 Aim the front point of the mouse at receiver.

PRESS THE BUTTON ON THE REAR SIDE OF MOUSE AND RELEASE, THEN PRESS THE

CONNECTOR BUTTON ON THE RECEIVER AND RELEASE WITHIN 15 SECONDS.

Move the mouse and the cursor is moving then the setup of mouse is completed .If the cursor is not moving ,

please repeat the above setup.

2. KEYBOARD

2.1 PRESS THE BUTTON ON THE REAR SIDE OF KEYBOARD AND RELEASE, THEN PRESS THE

CONNECTOR BUTTON ON THE RECEIVER AND RELEASE WITHIN 15 SECONDS.

Press the “Num Lock “key ，you can find the Num indicator light of receiver is changing status.

The setup of keyboard is completed. If not, please repeat the steps.

MOUSE BUTTON FUNCTION SETUP

1. Get into setup from the control desk or directly click into the mouse pattern show in right-down corner of

the screen . It shows the functions as following:

Button : setup for habit of using right or left hand, adjustment of the speed of continuously pressing twice

the mouse buttons, adjustment of numbers of column for each rolling.

Mouse Marking : to set up the pattern or mouse marking.

Wheel : to set up the functions of hot key, zooming ,and rolling of auto-turning.

Summary of content (3 pages)

PAGE 1
RF Keyboard & Mouse User Manual PRODUCT LIST When you have opened the package, please make sure that all accessories are included as below: Wireless Keyboard ×1 Wireless Mouse ×1 Receiver ×1 Driver Disk ×1 User’s instructional Guide ×1 Alkaline Batteries of size AA ×3 (for keyboard) Ni-MH Batteries of size AAA ×2 (for Mouse) In case of missing or damage of the above accessories, please contact your purchased dealer immediately.
PAGE 2
Motion : to set up the moving speed of mouse sign, the length of the dragging tail, and non-border, etc. 2. After the function is set u, press “Yes” to store the new setup. TROUBLESHOOTING If the mouse or keyboard doesn’t function well, please follow the steps below: 1. Check if the connector of USB or PS/2 port is well connected or not. 2. heck if the positive(+) and negative(-) pole of the battery is put correctly. If the power is low, the mouse will become sluggish or slow. 3.
PAGE 3
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.