Owner's manual

POST
x 2
PANEL
x1
RAILS
x 2
SC35B x8
(1.4”)
BRACKET
x4
fcb
u
POST
CAP x2
SC15 x12
(0.6”)
up
fcb
up
X3
Hole diameter (12”) 30cm
ASSEMBLY INSTRUCTIONS
DALLAS FENCE
ITEM : 000001 VER : 0 USA
IMPORTANT: You must read these instructions carefully before you start to assemble this fence. Please carry out the steps in the order set out in these instructions.Keep these instructions
in a safe place for future reference.
GENERAL INFORMATION: The Keter Fence is easy to install. We incorporate methods and procedures used by professional installers to guide you through to the successful
completion of your fence.
GENERAL ADVICE: This is a 2 person assembly job.If it is a property line fence, you will want to confirm your property lines
before ordering your fence.The component parts should be checked and laid out in an orderly way, close at hand.Keep all small parts
(screws, etc.) in a bowl so that they do not get lost.
Please keep the tracking number which appears on the box, and refer to this number when calling the service office for questions or complaints.
CARE & MAINTENANCE :When your fence needs a clean, use a mild detergent solution and rinse with cold clean water.
DO NOT use acetone, abrasive cleaners or other special detergents to clean the fence.
For general support and replacement parts, please contact :
U.S: Call Toll Free:1-(888)-374-4262 , fax [phone], 11495 North Pennsylvania ST., Suite 110 Carmel, Indiana, 46032, U.S.A
Canada: Tel: [phone] , Fax: [phone] , E-mail: [e-mail]
United Kindom: Keter (UK) Ltd. Unit 4, Woodgate Business Park, Clapgate Lane, Birmingham, B32 3DB, United Kindom. Tel: [phone], Fax: [phone]
The Netherlands: Keter Benelux, Ericssonstraat 17, Postbus 224, 5120 AE Rijen, The Netherlands. Tel: [phone], Fax: [phone]
TOOLS & MATERIALS
string line
post hole digger / power auger
mallet
work shoes
4 timber stakes
2”x 2”x24” (5cm x 5cm x 60cm)
concrete / dry mix
PARTS & DIMENSION
String fence line to show
horizontal accuracy
PROJECT PLANNING
1. Stake out fence from beginning to end.
.2. Estimate the ground level.
3. Start at the highest side of the fence line !
4. Dig hole under post line. make sure the
distance between holes centers is 6’ (183cm).
6’
183cm
183cm
183cm
183cm
183cm
6’
6’
6’
6’
3
GENERAL ADVICE ON POST HOLES POSITIONING GUIDE
5
BRACKETS ASSEMBLY FIXING FIRST POST
4
1. Use the positioning guide to place the brackets .
A. fold the positioning guide wings.
B. Attach the positioning guide to the post as shown.
C. Place the bracket within the positioning guide holes.
Top of
bracket
POST
TOP
1
A. Position the first post at the highest ground point of the fence line!
B. Place 2’’ (5cm) timber, under the bracket to maintain the gap between the fence and the ground.
C. Check for VERTICAL in two directions.
D. Fill the hole with concrete leaving a slope for water drainage.
E. Allow concrete to set for 10-15 minutes
Place first post in the hole, checking that it satisfies ALL the following conditions:
2
Gravel to reduce
frost HEAVE
(6”) 15cm
below frost line
Using post hole digger or power auger
or simple shovel dig the hole 12” (30cm)
in diameter. Main and gate posts should
be 6” (15cm) deeper for extra strength.
Backfill each hole with 6” of gravel to drain
water away.
(24”) 65cm hole depth
1.
using the positioning guide.
2.Do not assemble brackets on both sides
of the post !
3.Locate all bracket screws on center
of elongated holes on bracket for
expansion and contraction.
The lip of the bracket
should be on the
bottom.
www.keter.co.il
B
A
C D
builder's
level.
90
o
90
o
VERTICAL
C
D
ADD CONCRETE
2”
TIMBER
HEIGHT
B
GROUND
A
START AT THE HIGHEST
GROUND POINT
Attach two rail bracketsTS to One side of the posts
For fence sections that are less than the standard
6’ (183 cm) center-to-center, simply cut to size the
rails and the fence panels, using a power saw
(use metal fit blade).
.
A-13-00 544993