User's Manual

Cloud Camera
User Manual
1. Introduction
IP01 Cloud Camera is designed for middle, small enterprise & normal
family use and it can monitor your environment in 24 hours every day.
night time. It supports Wireless connection and it is convenient to setup
& operate.
• 802.11n Wireless Standard;
• Motion & sound detection;
• Wireless connection and no need for network wire connection;
• High quality level 720P CMOS sensor;
• Send snapshot or video to cloud server;
environment.
Dimensions 124 X 80 X 35mm
Weight 208 g
Audio Linear input/output two-way voice intercom
Audio compression PCM or ADPCM
Video compression H.264
Working frequency 50Hz / 60Hz
Video Format 720p / 512kbps , WVGA / 256kbps, WQVGA
/ 128kbps
Exposure balance Automatic
White balance Automatic
Infrared mode Automatic
Night vision 8 infrared lights, infrared irradiation
distance: 3-4meters
Supported protocol TCP/IP
Wireless standard WIFI(IEEE802.11b/g/n)
Support IP
addresses
Dynamic IP are supported
Operating
temperature
0° ~ 40°C
Operating humidity 10% ~ 85% (non-condensing)
Storage
temperature
-10°C ~ 60°
Storage humidity 10% ~ 85%(non-condensing)
Operation system Microsoft Windows 2000/XP, Vista,
Windows7, Windows8,Mac OS, Linux
Alarm detection Motion detection support
Noise Detection
3. Introduction on appearance
Front
Back
USB port
Microphone
Wi-Fi indicator
IR light
Camera
IR Sensor
Speaker
Reset
4. Ways to assemble wall mount
Right
Base
Wall mount
Wrong
5. Before setup
a) Connect your mobile to your Wi-Fi router
b) Connect the USB cable to the IP camera and the USB power adaptor,
plug in the power adaptor into the power socket
c) Wait for around 30 second for device startup, there is a flash green light
at the right on the IP camera
Output: 5V 1AInput: 5V 1A
6. Start up and register
a) Click the “DirectGear” on the screen
b) You will see the “DIRECTGEAR” logo shown
c) The first time you start, the Sign up screen will show
d) Type in an e-mail address and password into the relate field.
Retype the password for double confirm
e) Click the “Sign up” button to register
f) You will received an e-mail for the registration, click the link on the
e-mail to confirm
a) The first time login, it prompt for e-mail address and password
b) Click “Log in” after finish type in
a) If forgot the password, select the lower right corner “Forgot password”
at the “Log in”
b) Type in the e-mail address
c) Click “Send” and system will send an e-mail to your mailbox to reset
your password
a) After login, the first screen will show which said “Your account is lonely.
It needs a camera. Add on by tapping below.”
b) Click the “Add camera”
c) The add camera welcome screen will show
d) You need your mobile connect to the same Wi-Fi network.
Then click “OK”
e) Follow the instruction on the screen, then click “Next”
f ) Press the “Reset” button at the back of the IP camera for at least two
seconds until you hear a “beep” sound. Then click “Next” on the screen
i) It will scan the QR code on the mobile screen. Usually take 2~5 seconds.
After you hear the “beep beep” sound, you can click the “Yes, I heard it”
button.
j) It will automatic configure the IP camera, it need takes around 20 to 30
seconds.
k) After finished, it will show two fields which you can change the device
name and time zone. Click “Let’s go” after finish modify. Now the
camera is ready.
g) It will prompt to select the Wi-Fi network and input the password. Press
“Next” when finished.
h) Read the instruction on the screen. It asks you hold the mobile in front
of the camera between 10cm~20cm after click the “OK”.
DIRECTGEAR
7. The login
8. Forgot password
9. Add camera