KEN WOOD A907 HIDEAWAY TUNER AMPLIFIER INSTRUCTION MANUAL KEN WOOD CORPORATION Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new tuner amplifier. For your records ] Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below.
A Warning Dear Customer: Selecting fine audio equipment such as the unit you’ve just purchased is only the start of your musical enjoyment. Now it’s time to consider how you can maximize the fun and excitement your equipment offers. This manufacturer and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level.
Safety precautions : To prevent injury and/or fire, take the following precautions: * Ensure that the unit is securely instated. Otherwise it may fly out of place during collisions and other jolts. * When extending the ignition, battery or ground cables, make sure to use automotive-grade cables or other cables with an area of 0.
Installation W Accessories External view External view External view Number of items . Number of items Number of items ® The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above B Installation Procedure 1. To prevent a short circuit, turnover the key from the ignition and disconnect the @ battery. 2. Make the proper input and cutout wire connections for each unit. 3.
Installation W [installation for Hideaway unit ® Securing to audio board 1 Attach the installation brackets to the sides 2 jse the tapping screw (e4x16mm) to of the hideaway unit using the mess bolts secure the hideaway unit to the audio (Maxima) board.
Installation —— W Connecting Wires to Terminals If you connect the ignition wire (red) and the battery wire {yellow) to the car chassis {ground;}, you may cause a hart circuit, that in turn may start & fire. Always connect those wires to the power source running through the fuse box. Front deft output (Whig) ! PRECEPT & | REAGANOMICS_ FAINT Rear left output (White) / fl KEN WOOD Non-fading left cutout (White) o e Ko7 Rear right output (Red} fi P o Non-fading right output (Red) nemeses LL“‘\ Front right output
Contort unit {optional} V907 sage gy s s aoo. scram e ? Extension cable {Accessory) >S5 CAUTION switch setting Set the M-8 switch to 'S". LT \Fuselage) Changer control cable [Provided C307) Depending on what antenna you are using, connect dither to the control farming of the motor antenna, or to the power terminal for the boaster Motor antenna control wire (Blu) amplifier of the film-type antenna. 5 CONT QUTjmemms When using the optional power amplifier, connect to 1ts power control . .
Troubleshooting Guide What might appear to be a malfunction in your unit may just be the result of slight commiseration or misfiring. Before calling service, first check the following table for possible problems. PROBLEM POSSIBLE CAUSE SOLUTION The power does not turn on The fuse has blown Afar checking for short circuits in the cables, replace the fuse with cne acing the same rating. Ne sound can be heard, er he volume is low.
Specifications Specifications subject to change without notice. FM tuner section Frequency range {200 kHz Space] .. Usable sensitivity {S/N = 30 dB} Quieting Sensitivity (S/N = 50 dB} Frequency response (3.0 dB} . Signal to Noise ratio (MONO} Selectivity {£400 kHz} Stereo separation {1 kHz) 107.9 MHz 0.8 pvi75 Q) B (1.6 uV/75 kHz 70 dB AM tuner section Frequency range (10 kHz B30 kHz 1700 kHz Us Sable SENSITIVITY L i L..28 dB (25 pV} Audio section Maxim urn cutout power L ADW referee 100 Hz 210 dB .