INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES VHF APCO P25 TRANSCEIVER TRANSCEPTOR APCO P25 VHF TK-5210 © B62-1796-10 (K) 09 08 07 06 05 04 03 02 01
THANK YOU We are grateful you chose KENWOOD for your land mobile radio applications. We believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency. KENWOOD transceivers incorporate the latest in advanced technology. As a result, we feel strongly that you will be pleased with the quality and features of this product.
One or more of the following statements may be applicable: FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
UNPACKING AND CHECKING EQUIPMENT Note: The following unpacking instructions are for use by your KENWOOD dealer, an authorized KENWOOD service facility, or the factory. Carefully unpack the transceiver. We recommend that you identify the items listed in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, file a claim with the carrier immediately.
Front 2 3 1 4 5 Type 3 No.
Side 1 2 3 4 Left side No.
Key (Power SW/Volume) (Selector) (Concentric Switch) (Lever Switch) (Orange) (Side 1) (Side 2) (Side 3) (PTT) (A) (B) (C) (D) (DTMF 12 Key) Type1 Power Switch/Volume 16 Position Rotaly SW 3 Position Selector 2 Position Selector Orange Side 1 Side 2 Side 3 PTT ------ Type2 Power Switch/Volume 16 Position Rotaly SW 3 Position Selector 2 Position Selector Orange Side 1 Side 2 Side 3 PTT A B C D -- Type3 Power Switch/ Volume 16 Position Rotaly SW 3 Position Selector 2 Position Selector Orange Side 1 Side 2 S
1.
PREPARATION INSTALLING/ REMOVING THE (OPTIONAL) BATTERY PACK CAUTION: -DO NOT RECHARGE HE BATTERY PACK IF IT IS ALREADY FULLY CHARGED. DOING SO MAY CAUSE THE LIFE OF THE BATTERY PACK TO SHORTEN OR THE BATTERY PACK MAY BE DAMAGED. -AFTER RECHARGING THE BATTERY PACK, DISCONNECT IT FROM THE CHARGER. IF THE CHARGER POWER IS RESET (TURNED ON AFTER BEING TURNED OFF), RECHARGING WILL START AGAIN AND THE BATTERY PACK WILL BECOME OVERCHARGED. -DO NOT SHORT THE BATTERY TERMINALS OR DISPOSE OF THE BATTERY BY FIRE.
THE ANTENNA INSTALLING Screw the antenna into the connector on the top of the transceiver by holding theantenna at its base and turning it clockwise until secure. INSTALLING THE BELT CLIP If necessary, attach the belt clip using the two supplied binding screws. Note: If the belt clip is not installed, its mounting location may get hotduring continuous transmission or when left sitting in a hot environment.
INSTALLING THE COVER OVER THE UNIVERSAL CONNECTOR If you are not using the optional KMC-** speaker/ microphone, install the cover over the universal connector using the supplied 4 x 6 mm dressing screw. INSTALLING THE (OPTIONAL KMC-25, KMC-25W) SPEAKER/ MICROPHONE 1 Insert the guide of the speaker/ microphone connector into the groove of the universal connector. 2 Secure the connector in place using the attached screw.
RADIO FREQUENCY ENERGY SAFETY INFORMATION _____ This KENWOOD transceiver has been tested and complies with the standards listed below, in regards to Radio Frequency (RF) energy and electromagnetic energy (EME) generated by the transceiver. • FCC RF exposure limits for Occupational Use Only. RF Exposure limits adopted by the FCC are generally based on recommendations from the National Council on Radiation Protection and Measurements, & the American National Standards Institute.