POWER AMPLIFIER LAC-526 INSTRUCTION MANUAL KEN WOOD GREENWOOD CORPORATION © BRA-0787-00 (K) (MC) Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new power amplifier. For your records Record the serial number, found on the back of the unit, in the spaces. designated on the warranty card, and In the space provided below.
ML Operations of the following control and switches are required in accordance with the center. unit and speakers connected with this unit. @ RCA CABLE GROUND LEAD terminal (@ OPERATION switch This switch allows to select the amplification method of input signals. * STEREO position The input left and right signals are amplified separately. Use this position when the units as a stereo amplifier, * MONO {Lch) position Amplifies the signal input from the left side only.
g POWER INDICATOR When the power is turned on, the Power indicator lights, If the Power indicator doss nat light when the power is turned on, the protection function may be activated. Check whether there is any indication of troubles. This unit is equipped with 3 protection function for protecting this unit and your speakers from various accidents or problems that can scour. _ When the protection function is triggered, the Power indicator goes off and the amplifier spats operating.
Installation procedure . Remove the ignition key and disconnect the negative & terminal of the battery 1o prevent short circuits, . Connect the input and output cables of the units. . Connect the speaker cables, . Concert the ground cable and battery cable In the order listed, . Install the unit in the car. . Connect the negative ) terminal of the battery. the fuse blows, check cables for shorts, then replace the fuse with one of the same rating.
: (R With the LAC-5286, a sub woofer gan be added easily 10 the speaker system by marking use of the properties of coll and capacitors. This mode of operation Js called Ti-mode. W Principle of Ti-mode ® Method of frequency band division using a coil and capacitor intestine case of 6dB/oct. slope Cu put Crossover Frequency Frequency Output Frequency Frequency * Coil (LI Passes low frequencies and blocks high frequencies.
LT T M System connection RCA cable ground lead terminal ‘When using an RCA cable with a ground lad attached, connect the ground lead to this terminal, @® Do nat connect cables and leads to both RCA cable input jacks and the speaker input terminals simultaneously, for this may cause malfunction or damages. ‘ Left output (White) CENTER UNIT {Cassette receiver, Graphic equalizer ate,) Power control! lead {Commercially available part) CAUTION P Do not use this terminal for power source grounding.
Connection W Connection with genuine-accessory car stereo Speaker love input terminal Connect the speaker level nut cable to this terminal, Polarity of speaker Genuine-accessory car stereo ignition key m Switch input terminals Car fuse Box E “exasperate la vol input cable Terminate cover n et Ao Power canto! lead Mercilessly titillate pray CAUTION The genuine-accessory car stern shall have a maximum power output of no more tho not connect the speaker output leads from a power amplifier [Optional} to the spe
TS T e Often, what appears to be a malfunction is due to user error. Before calling for service, please consult the following table. Symptom Cruse Remedy No sound. Input {or output cables are Connect the input {No sound from one side,} disconnected. {or output) cables. The output level is too The input sensitivity adjusting Adjust the control correctly small (or too large). control is nat set 16 the correct referring to "Controls”, petition. The sound quality is bad.
KENDO AMPLIFICATEUR DE PUISSANCE KAC-526 MODE D'EMPLOI KENDO CORPORATION € () (MC) Précautions de sécurité Pour éviter tout risque de feu et de blessures physiques, observer les précautions suivantes : * Aile besoin de rallonger I'un des clébes d'alimentation {masse, la batterie} utiliser des chables de catégorie automobile d'une section minimum de 3 rm? (AWG12) ou puis afin d'éviter toute détérioration de ces derniers. * Vérifier que 'on n'a pas laissé d'objets métalliques {pinces de monnaie, outils, etc.
VTR T T Les réglages suivants doivent &ire effectués pour adapter |'appareil & l'unité centrale et aux haut-parleurs qui lui sont raccordés. (D Borne RCA CÂBLE ROUND DEAL (fil de mise & la masse du cible RCA) @ Commutateur OPÉRATION Ce commutateur est destin & la sélection du mod d'amplification des signaux d'entrés. * Position RESTER Les signaux d'entrée droit et gauche sont amplifiés séparément. C'est fa position & utiliser lorsque Appareil sert d’amplificateur stéréo.
onction de protection Indicateur POSER (alimentation) Lorsque l"alimentation est activée, l'indicateur POSER s’illumine. Si l’indicateur POSER ne s'illumine pas lorsque "alimentation est activée, la fonction de protection pourrave se déclencher, Vérifier glatit v a un problème, Cet appareil est pourvu d'une fonction de protection de Appareil lui-même et des haut-parleurs de maniérer & éviter divers incidents.
Retirer [a ¢l de contact et débrancher la baume négative & de l2 batterie pour éviter les courts-circuits, 2. Raccorder les cibles d’entrée ot de sortie de J'appareil, 3. Raccorder les cibles de haut-parleur. 4. Raccorder ie cible da masse e le cible de Iz batterie du faisceau de fils dans cet ordre. 5. Monter 'appareil dans le voiture., 8. Raccorder la borne négative & de e batterie.
Avec le KACHA, 1l est facile d'ajouter au système de haut-parleurs un haut-parleur d’extrême grave en mettant 2 profit les propriétés des bobines st des condensateurs. Ce mode de fonctionnement s'appelle Is Tri-mode. Principe du Tri-mode ® Méthode de division de la bande des basses fréquences au moyen d’une bobine et condensateur dans le cas d’une pente de 6dB/oct.
WRaccordement avec un autoradio stéréo d'origine Borne d’entrée au niveau haut-parleur Relier & cette borne le câble transportant le signal au niveau titrisée haut-parleur 4771 Haut parleur <, | atone Autoradio stéréo d'origine et HUE Clé e contact ) & guetteur AT Polarité dos bromes o marmitage
Guide de dépannage Bien souvent, ¢ce gui semble un mauvais fonctionnement de Appareil est di 4 une manipulation erronée de Utilisateur. Avant de faire appel au réparateur, passer la tableau suivant en revue. Symptôme Cause Solution Absence de sons. Les câbles d'entrée {ou de Brancher las câbles d’entrée {Pas de son d"un coté} sortie} sont débranchés, {ou de sortir. Niveau de sortie trop La commande de réglage de la Faire le réglage correctement en faible. {ou trop fort} sensibilité d’entrée n'est pas se.