DMX4707S DMX47S DMX5020S MONITOR WITH RECEIVER INSTRUCTION MANUAL • Updated information (the latest Instruction Manual, system updates, new functions, etc.) is available from . Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new receiver.
Contents Before Use 4 Radio 18 Precautions.................................................................... 4 Radio Basic Operation.............................................18 How to read this manual.......................................... 4 Memory Operation...................................................19 Selecting Operation.................................................19 Basic Operations 5 Functions of the Buttons on the Front Panel.... 5 Turning on the Unit....................
Setting Up 37 Monitor Screen Setup..............................................37 System Setup..............................................................37 User Interface Setup.................................................38 Special Setup..............................................................39 Display Setup..............................................................39 AV Setup.......................................................................
Before Use Before Use Precautions # WARNINGS ÑÑTo prevent injury or fire, take ÑÑHow To Reset Your Unit • If the unit or the connected unit fails to operate properly, reset the unit. Press the button.The unit returns to factory settings. the following precautions: • To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit. • Do not watch or fix your eyes on the unit’s display when you are driving for any extended period.
Basic Operations Basic Operations Functions of the Buttons on the Front Panel Turning on the Unit The method of turning on is different depending on the model. 1 1 Press the [HOME] button. 2 3 4 5 hh The unit is turned on. 6 NOTE • The panels shown in this guide are examples used to provide clear explanations of the operations. For this reason, they may be different from the actual panels. Name ●● To turn off the unit: 1 Press the [HOME] button for 1 second.
Basic Operations Getting Started ■■ [Camera] Set the parameters for the camera. 1 Touch [Camera]. 2 Set each item and touch [ ]. For detailed operation, see Camera Setup (P.35). Initial setup Perform this setup when you use this unit first time. 1 ■■ [DEMO] Set the demonstration mode. Default is “ON”. 1 Touch [DEMO] and set [ON] or [OFF]. Set each item as follows. 2 ■■ [Language] Select the language used for the control screen and setting items. Default is “[American English(en)]”.
Basic Operations 3 Touch [User Interface]. Adjusting the volume To adjust the volume (0 to 40), Press [R] to increase, and press [S] to decrease. Holding [R] increases the volume continuously to level 15. hh User Interface screen appears. 4 Touch [Clock Adjust]. Touch screen operations To perform operations on the screen, you need to touch, touch and hold, flick or swipe to select an item, display setting menu screen or to change the page, etc.
Basic Operations HOME screen descriptions Source selection screen descriptions Most functions can be performed from the HOME screen. 1 3 2 4 You can display all playback sources and options on the source selection screen. 1 5 1 • Displays the control screen of current source. 2 • Current source information 3 • Displays the source selection screen. (P.9) 4 • Short-cut playback source icons (P.9) 5 • Displays the Hands Free screen. (P.
Basic Operations Select the playback source 1 To select the playback source on the HOME screen Touch [ ] on the HOME screen. From the screen, you can select the following sources and functions. • Switches to the USB Mirroring screen from the connected Android smartphone. (P.14) It is necessary to connect Android smartphone with “Mirroring OA for KENWOOD” application installed and to set [Mode] to [Mirroring for Android™]. (P.14) • Switches to the Apple CarPlay screen from the connected iPhone. (P.
Basic Operations Customize Short-cut buttons on HOME screen You can arrange the position of the source icons as you like. 1 Touch [ 2 Touch and hold the icon which you want to move to go into the customizing mode. 3 ] on the HOME screen. 3 Secondary screen • [ ]/[ ] : The Secondary screen changes every time you touch it. You can also change the Secondary screen by flicking left or right on the screen. • Indicators: Displays the current source condition and so on.
Basic Operations MENU screen 1 Press the [MENU] button. List screen There are some common function keys in the list screens of most sources. 1 2 6 hh MENU screen appears. 2 Touch to display the MENU screen. 3 4 5 1 Displays list type selection window. The contents of the menu are as follows. 2 • Displays the SETUP Menu screen. (P.37) Displays music/movie file list. • Displays the APP (Apple CarPlay/ Android Auto) screen. (P.12) Scrolls the displayed text.
APPS APPS Apple CarPlay Operation Apple CarPlay is a smarter, safer way to use your iPhone in the car. Apple CarPlay takes the things you want to do with iPhone while driving and displays them on the screen of the product. You can get directions, make calls, send and receive messages, and listen to the music from iPhone while driving. You can also use Siri voice control to make it easier to operate iPhone. For details about Apple CarPlay, visit https://www.apple.com/ios/carplay/.
APPS Android Auto™ Operation Android Auto enables you to use functions of your Android smartphone convenient for driving. You can easily access route guidance, make calls, listen to music, and access convenient functions on the Android smartphone while driving. For details about Android Auto, visit https://www.android.com/auto/ and https://support.google.com/androidauto. Compatible Android smartphone You can use Android Auto with Android smartphone of Android version 5.0 or later.
APPS USB Mirroring Operation (Android only) You can display and control the App on the unit while your smartphone is connected to the USB terminal. ÑÑPreparation 1 2 2 3 4 5 smartphone • Android version 7.0 or later • Linux Kernel version 3.5 or later • Bluetooth support NOTE • This unit may not work for some Android smartphone's. Download Mirroring App from the Google Play. Install the latest version of the Mirroring application “Mirroring OA for KENWOOD” on your Android.
USB USB Connecting a USB device 1 Connect the USB device with the USB cable. (P.50) USB Basic Operation Most functions can be controlled from the source control screen and playback screen. Control screen 7 2 3 4 2 5 Press the [HOME] button. Touch [ ]. Touch [USB]. (P.9) ÑÑDisconnect the USB device 1 2 3 4 1 4 6 Open the drawer 4 Press the [HOME] button. Touch [ 3 5 ]. Touch a source other than [USB]. Detach the USB device.
USB Video screen 3 [Operation keys • [1] : Searches track/file. For details on search operation, see Search Operation (P.17). • [E] [F] : Searches the previous/next track/ file. Touch and hold to fast forward or fast backward. • [D]H] : Plays or pauses. •[ ] : Touch to mute or not to mute. 4 Function panel Touch on the left side of the screen to display the function panel. Touch again to close the panel. •[ ] [ ] : Searches previous/next folder. • [ASPECT](Only during video playback): Select screen mode.
USB Search Operation You can search music or video files by the following operations. 1 2 3 Touch [1]. Touch [S]. ÑÑLink search You can search a file of same artist/album/genre as the current track. 1 2 • For operations in the list screen, see List screen (P.11). ÑÑCategory search You can search a file by selecting category. 3 Touch the desired tag type. You can select from artist, album and genre. Select the list type. hh The list corresponding to your selection appears.
Radio Radio Radio Basic Operation 3 Operation keys Most functions can be controlled from the source control screen. To enter Radio source, touch [Radio] icon in the source selection screen. (P.9) Control screen 4 Preset list • Touch on the right side of the screen to display the Preset list. Touch again to close the list. • Recalls the memorized station. • When touched for 2 seconds, stores the current receiving station in memory. 4 1 • [E] [F] : Tunes in a station.
Radio Memory Operation Selecting Operation ÑÑAuto memory ÑÑPreset select You can store stations with good reception in memory automatically. You can list and select memorized station. 1 2 Touch desired band key. Touch [ ] on the left side of the screen. Touch [AME]. 1 Touch [ ] on the right side of the screen. Select a station from the list. ÑÑSearch by program type (FM only) You can tune to a station with a specific program type when listening to FM.
Radio Traffic Information (FM only) You can listen and watch the traffic information automatically when a traffic bulletin starts. However, this feature requires a Radio Broadcast Data System that includes the TI information. 1 Radio Setup (FM only) You can set tuner related parameters. 1 Touch [ ] on the left side of the screen. Touch [SETUP]. Touch [ ] on the left side of the screen. Touch [TI]. hh Radio SETUP screen appears. 2 hh Traffic information mode is set.
SiriusXM® SiriusXM® (DMX4707S/ DMX47S) SiriusXM® Basic Operation Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit www.siriusxm.com. To listen to the SiriusXM source, touch the [SiriusXM] icon on the source selection screen. (P.
SiriusXM® 3 Artwork / Function panel • Displays the album artwork for most SiriusXM music channels. • Touch [ ] of the screen to display the function panel. Touch [ ] to close the panel. –– [Direct Channel]: Touch and enter the desired number. For details, see Direct search (P.23). –– [SETUP]: Touch to display the SiriusXM SETUP screen. For details, see SiriusXM Setup (P.24). –– [Replay/Live]: Touch to turn on or off the replay mode. See Replay (P.24).
SiriusXM® Direct search You can tune in a channel directly. 1 2 Touch [ ] on the left side of the screen. Touch [Direct Channel]. Category/Channel search You can specify the desired category and select a channel. 1 Touch [1]. 2 Select a category. Enter the channel number and touch [Enter]. hh Channel list appears. 3 Select the desired content from the list. *1 NOTE • To clear the number you entered, touch [BS]. *1 Select a desired item ([Info], [CH Name], [Artist], [Title]).
SiriusXM® Replay You can replay the last 60 minutes of the program from the current channel. 1 SiriusXM Setup 1 Touch [ ] on the left side of the screen. Touch [SETUP]. Touch [L] or [Replay] on the function panel. ■■ [E] [F] Press to skip to the previous/next track. Press and hold to rewind or fast forward. ■■ [DH] Plays or pauses. ■■ Replay time bar/Play mode indicator Displays the recorded data capacity and playback position. [D], [B], etc.
SiriusXM® ÑÑParental code ÑÑParental Control You can set a SiriusXM parental code for Parental Control. The Parental Control feature allows you to limit access to any SiriusXM channels, including those with mature content. When enabled, the Parental Control feature requires you to enter a Parental Code to tune to the locked channels. 1 Touch [Parental Code] on the SiriusXM SETUP screen. hh Parental Code Set screen appears. NOTE • The code number is set to “1111” as default.
SiriusXM® When selecting [User] 4 This allows you to limit access to any SiriusXM channel (Parental Lock Channel). 1 Touch [Parental Lock Channel Selection] on the SiriusXM SETUP screen. hh Parental Lock Code screen appears. Touch each channel on the list and set to [ON] or [OFF]. [ON]: Locks the channel. [OFF]: Unlocks the channel. *1 NOTE • You need to set up a parental code beforehand as stated in Parental code (P.25).
Bluetooth Control Bluetooth Control Using the Bluetooth function, various functions can be used: listening to the audio file, making/ receiving a call. Information for using Bluetooth® devices Bluetooth is a short-range wireless radio communication technology for mobile devices such as mobile phones, portable PCs, and other devices. Bluetooth devices can be connected without cables and communicate with each other.
Bluetooth Control Register from the Bluetooth device It is necessary to register the Bluetooth audio player or cell-phone to this unit before using the Bluetooth function. You can register up to 7 Bluetooth devices. Bluetooth Setup 1 2 Press the [MENU] button. hh MENU screen appears. Touch [ ]. NOTE • Up to 7 Bluetooth devices can be registered. If an attempt is made to register the 8th Bluetooth device, the Bluetooth device connected on the earliest date will be deleted to register the 8th one.
Bluetooth Control ÑÑConnect the Bluetooth device 1 Touch [Select Device] in the Bluetooth SETUP screen. Playing Bluetooth Audio Device Most function can be controlled from the source control screen. To enter Bluetooth source, touch [Bluetooth] icon in the source selection screen. (P.9) ÑÑBluetooth basic operation Control screen 5 2 Touch [ ] you want to connect. 1 2 4 3 1 Device name/ [ NOTE • If the icon is lighted, it means that the unit will use that device.
Bluetooth Control 4 Function panel 2 Touch on the left side of the screen to display the function panel. Touch again to close the panel. • [BT DEVICE CHANGE] : Selects the device to connect via Bluetooth audio (A2DP) or APP (SPP). See Connect the Bluetooth audio (P.30). Touch the device name you want to connect. 5 Play mode indicator/ Playing time [D], [H]: Current play mode indicator The meanings of each icon are as follows; [D] (play), [B] (fast forward), [A] (fast backward), [H] (pause).
Bluetooth Control Using Hands-Free Unit You can use telephone function by connecting the Bluetooth telephone to this unit. NOTE • While Apple CarPlay or Android Auto is being connected, Bluetooth Hands-Free function cannot be used. Only Apple CarPlay or Android Auto Hands-Free function can be used. ●● Bluetooth SETUP 1) Touch [ ]. Bluetooth SETUP screen appears. NOTE • The status icons such as battery and antenna displayed may differ from those displayed on the cell-phone.
Bluetooth Control Call using the preset number ÑÑVoice Recognition 1 2 You can access the voice recognition function of the cell-phone connected to this unit. You can search the cell-phone phonebook by voice. (The functionality depends on the cell-phone.) Touch [ ]. Touch the Name or phone number. 1 Press the [VOICE] button. hh Voice Recognition screen appears. 2 Call using the phonebook 1 2 3 Touch [ ]. Start speaking.
Bluetooth Control ÑÑReceive a call 1 ÑÑOperations during a call Touch [ ] to answer a phone call or [ to reject an incoming call. ] ●● Adjust the receiver volume Press the [S] or [R] button. NOTE • While monitoring the view camera, this screen does not appear even if a call comes in. To display this screen, return the shift knob of car to the driver position. To end call 1 While talking, touch [ ]. ●● Output the dial tone Touch [DTMF] to display the tone input screen.
Bluetooth Control ÑÑPhone number preset ■■ [Delete] To delete a preset number, touch [Delete] and then touch [Yes] on the confirmation screen. You can register frequently used phone numbers to this unit. 1 2 Touch [ ]. Touch [Edit]. ÑÑPhonebook transfer You can transfer the phonebook in your Bluetooth smartphone via PBAP. 1 2 3 Touch [ ]. Touch [ ]. Select where to preset. hh The phonebook data transmission starts.
Other External Components Other External Components ÑÑCamera Setup View Camera 1 NOTE • To connect a camera, see P.50. • To use a rear view camera, a REVERSE lead connection is required. (P.50) • The rear view screen is displayed when you shift the gear to the reverse (R) position. 2 3 Press the [MENU] button. hh MENU screen appears. Touch [ ]. hh SETUP Menu screen appears. Touch [Camera]. ÑÑDisplay the camera screen 1 2 Press the [MENU] button. hh MENU screen appears.
Other External Components To adjust the parking guidelines NOTE External audio/video players— AV-IN • Install the rear view camera in the appropriate position according to the instructions supplied with the rear view camera. 1 • When adjusting the parking guidelines, make sure to use the parking brake to prevent the car from moving. 2 3 1 2 3 4 Connect an external component to the AV-IN input terminal. (P.50) Select [AV-IN] as the source. (P.
Setting Up Setting Up Monitor Screen Setup You can adjust image quality in video screen. 1 2 Press the [MENU] button. hh MENU screen appears. Touch [ ]. System Setup 1 2 Press the [MENU] button. hh MENU screen appears. Touch [ ]. hh Screen Control screen appears. 3 Adjust each item as follows. ■■ [Contrast] / [Brightness] / [Color] / [Tint] Adjusts each item. NOTE • Adjusting items are different depending on the current source. hh See the following section for each setting. • Set up AV (P.
Setting Up User Interface Setup You can setup user interface parameters. 1 2 3 Press the [MENU] button. hh MENU screen appears. Touch [ ]. hh SETUP screen appears. Touch [User Interface]. ÑÑLearning function of steering remote (DMX5020S only) This function is available only when your vehicle is equipped with the electrical steering remote controller. If your steering remote controller is not compliant, learning may not be completed and error message may appear.
Setting Up Special Setup You can setup Special parameters. 1 2 3 Press the [MENU] button. hh MENU screen appears. Touch [ ]. hh SETUP screen appears. Display Setup 1 2 3 Press the [MENU] button. hh MENU screen appears. Touch [ ]. hh SETUP screen appears. Touch [Display]. Touch [Special]. hh Display screen appears. hh Special screen appears. 4 4 Set each item as follows. ■■ [Dimmer] Select dimmer mode. [OFF]: The display and buttons do not dim. [ON]: The display and buttons dim.
Setting Up To register original image You can load an image from the connected USB device and set it for the background image. Before operating this procedure, it is necessary to connect the device which has the image to load. 1 2 AV Setup You can set AV parameters. 1 Touch [User1 Select] or [User2 Select] in the Background screen. 2 Select the image to load. 3 Press the [MENU] button. hh MENU screen appears. Touch [ ]. hh SETUP screen appears. Touch [AV]. hh AV screen appears.
Controlling Audio Controlling Audio You can adjust the various settings such as audio balance or subwoofer level. 1 2 Press the [MENU] button. hh MENU screen appears. Touch [ ]. Speaker/ X’over setup 1 2 3 4 hh See the following section for each setting. • Set up speaker/ X’over (P.41) • Controlling equalizer (P.43) • Set listening position/ DTA (P.45) • Controlling general audio (Fader / Balance) (P.42) • Set volume offset (P.44) • Set sound effect (P.44) 5 Press the [MENU] button.
Controlling Audio ■■ [Tweeter] (Only for Front) You can set the tweeter when you are selecting front speakers. [None], [Small], [Medium], [Large] ■■ [TW] (Tweeter) [Gain]*2 Adjusts the tweeter level. (When front is selected on Speaker Select screen) ■■ [Phase Inversion]*3 Sets the phase of subwoofer output. Check [Phase Inversion] to shift the phase 180 degrees. (When subwoofer is selected on Speaker Select screen) ■■ [Xʼover] Displays the speaker crossover setup screen.
Controlling Audio Equalizer Control ■■ [SW Level] Adjusts the subwoofer volume. You can adjust equalizer by selecting the optimized setting for each category. ÑÑRecall the EQ curve 1 1 2 2 3 4 Press the [MENU] button. hh MENU screen appears. Touch [Preset Select]. Select EQ curve. Touch [ ]. hh Audio screen appears. Touch [Equalizer]. Touch the screen and set the Graphic Equalizer as desired. ÑÑSave the EQ curve 1 2 3 Adjust the EQ curve. Touch [Memory]. Select where to save.
Controlling Audio Volume Offset Finely adjust the volume of the current source to minimize the difference in volume between different sources. 1 2 3 4 Sound Effect You can set sound effects. 1 Press the [MENU] button. hh MENU screen appears. Press the [MENU] button. hh MENU screen appears. 2 Touch [ ]. hh Audio screen appears. 3 Touch [Sound Effect]. 4 Set each item as follows. Touch [ ]. hh Audio screen appears. Touch [Volume Offset]. Touch [+] or [−] to adjust the level.
Controlling Audio Listening Position/ DTA Adjust the sound delay time as nearer speakers to the selected seat have more delay time, so that the sound from each speaker arrive a listener at the same time. 1 2 3 4 Press the [MENU] button. hh MENU screen appears. Position DTA control You can fine-adjust your listening position. 1 2 3 Touch [Adjust]. Touch [Delay]. Touch [T] or [U] to adjust the delay time of the selected speaker. Touch [ ]. hh Audio screen appears. Touch [Position/DTA].
Remote control Remote control This unit can be operated using the remote control KNA-RCDV331 (optional accessory). 6 E F ÑÑSwitch the operation mode Turn its operation mode switch to “AUD.” 7 ATT 8 Numeric AUD Allows you to enter the number to search in the direct search mode. For details on the direct search mode, see Direct search mode (P.46). Switches to the direct search mode. 9 [# BS] For details on the direct search mode, [DIRECT] see Direct search mode (P.46). Not used.
Connection/Installation Connection/Installation Before Installation Before installation of this unit, please note the following precautions. # WARNINGS • If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. • Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow).
Connection/Installation ÑÑSupplied accessories for Installing the unit installation 1 ÑÑNon-Japanese cars 2 (Except DMX5020S) (3 m) x1 x1 3 4 (2 m) x1 5 x1 (M5 × 6 mm) (M5 × 8 mm) x6 7 x6 8 x1 9 NOTE x1 [1] x2 [1] Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. 6 E xcept DMX5020S • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip).
Connection/Installation ÑÑMicrophone unit ÑÑRemoving the unit 1) Check the installation position of the microphone (accessory 1). 2) Clean the installation surface. 3) Remove the separator of the microphone (accessory 1), and stick the microphone to the place shown below. 4) Wire the microphone cable up to the unit with it secured at several positions using tape or other desired method. 5) Adjust the direction of the microphone (accessory 1) to the driver.
Connection/Installation ÑÑConnecting wires to terminals Connect to vehicle’s steering remote harness. Contact your KENWOOD dealer for details. (DMX5020S only) ST REMOTE INPUT 1 Bright Green/Red ST REMOTE INPUT 2 Purple/Red ST REMOTE GND Gray/Red STEERING WHEEL REMOTE INPUT Light Blue/Yellow (Steering remote control wire) To steering remote To use the steering wheel remote control feature, you need an exclusive remote adapter (not supplied) matched to your car. USB terminal[1] (1.0 m) 5V=1.
Connection/Installation ÑÑConnecting an iPhone/Android Android smartphone[2] USB cable [2] 1 3 5 7 2 4 6 8 iPhone[2] Lightning connector 1 3 5 7 2 4 6 8 KCA-iP103 (0.8m)[3] Accessory 7 Accessory 8 Speaker impedance: 4-8 Ω White White/Black Gray USB terminal[1] (1.0 m) To front left speaker 5V=1.5A Cap To front right speaker Gray/Black Green To rear left speaker Green/Black Purple To rear right speaker Purple/Black P.CONT ANT.
Troubleshooting Troubleshooting Problems and Solutions If any trouble occurs, first check the following table for possible problems. NOTE • Some functions of this unit may be disabled by some settings made on this unit. • What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. ÑÑAbout settings • Cannot set up the subwoofer. • Cannot set up subwoofer phase. • No output from the subwoofer. • Cannot set up the low pass filter.
Troubleshooting ÑÑSiriusXM (Except DMX5020S) [Check Tuner] A SiriusXM tuner is not connected to this unit. Verify that the SiriusXM Connect Vehicle Tuner cable is securely connected to the radio. [Subscription Updated - Press Return To Continue] The SiriusXM subscription has been renewed. Touching [Return] on the popup screen will clear the message. [Channel *** Not Available] The currently selected channel is unavailable. Visit www.siriusxm.
Appendix Appendix Playable Media and Files You can play various kinds of media and files on this unit. ÑÑAbout files The following audio and video files are supported. ■■Playable Audio files Format AAC-LC (.m4a) MPEG2/4 AAC LC HE-AAC(V1,V2) MP3 (.mp3) MPEG 1/2 Audio Layer 3 WMA (.wma) Windows Media Audio Standard L3 profile (Version 7,8,9) Linear PCM RIFF waveform Audio Format (WAVE) (.wav) FLAC (.flac) flac Vorbis (.
Appendix Specifications ■■Monitor section Picture Size : 6.75 inches (diagonal) wide : 151.8 mm (W) × 79.7 mm (H) 5-15/16 × 3-1/8 inch Display System : Transparent TN LCD panel Drive System : TFT active matrix system Number of Pixels : 1,152,000 (800H × 480V × RGB) Effective Pixels : 99.99% Pixel Arrangement : RGB striped arrangement Back Lighting : LED ■■USB interface section USB Standard : USB 2.0 High Speed File System : FAT 16/ 32, exFAT Maximum Power Supply Current : DC 5 V 1.
Appendix ■■FM tuner section ■■Audio section Frequency Range (step) DMX4707S/ DMX47S : 87.9 MHz – 107.9 MHz (200 kHz) DMX5020S : 87.5 MHz – 108.0 MHz (50 kHz) Maximum Power Output (Front & Rear) : 45 W × 4 Usable Sensitivity (S/N: 30 dB) : 16.2 dBf (1.8 μV/75 Ω) Frequency Response (± 3.
Appendix About this Unit ■■Copyrights • The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by JVCKENWOOD Corporation is under license. Other trademarks and trade names are those of their respective owners. • Windows Media is a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. • This product is protected by certain intellectual property rights of Microsoft.
Appendix –– Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. –– Neither the name of the Xiph.org Foundation nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
Appendix This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. ■■IC (Industry Canada) Caution This device contains licence-exempt transmitter(s)/ receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Important Notice on Software EULA ÑÑSoftware License on This Product ÑÑSoftware License Agreement The software embedded in this product comprises a number of independent software components, each of which is copyrighted by JVCKENWOOD Corporation or by a third party. JVCKENWOOD Corporation (hereinafter called “Licensor”) holds either the copyright to the embedded software or the right to sublicense it. This agreement establishes the conditions under which the customer uses this “Licensed Software.
Article 3 (Terms of License) Article 8 (Cancellation of the Agreement) 1. In assigning this product, User may not retain the original copy of the embedded Licensed Software (including associated literature, updates and upgrades) and any duplicates and associated literature with regard to the license to use Licensed Software. User may transfer Licensed Software only to the condition of binding the assignee to abide by the terms of this Software License Agreement.
!B5H-0358-20_DMX_KR_En.
DMX4707S DMX47S DMX5020S MONITOR WITH RECEIVER Quick Start Guide MONITOR CON RECEPTOR Guía de inicio rápido MONITEUR AVEC RÉCEPTEUR Guide de démarrage rapide • Updated information (the latest Instruction Manual, system updates, new functions, etc.) is available from • Encontrará la información actualizada (el manual de instrucciones más reciente, actualizaciones del sistema, nuevas funciones, etc.
Important Notice on Software EULA ÑÑSoftware License on This Product ÑÑSoftware License Agreement The software embedded in this product comprises a number of independent software components, each of which is copyrighted by JVCKENWOOD Corporation or by a third party. JVCKENWOOD Corporation (hereinafter called “Licensor”) holds either the copyright to the embedded software or the right to sublicense it. This agreement establishes the conditions under which the customer uses this “Licensed Software.
Article 3 (Terms of License) Article 8 (Cancellation of the Agreement) 1. In assigning this product, User may not retain the original copy of the embedded Licensed Software (including associated literature, updates and upgrades) and any duplicates and associated literature with regard to the license to use Licensed Software. User may transfer Licensed Software only to the condition of binding the assignee to abide by the terms of this Software License Agreement.
Before Use Contents Before Use...................................................................... 4 About the Quick start guide............................................................4 How to read this manual...................................................................4 Precautions.................................................................................................5 Basic Operations..........................................................
Before Use Precautions # WARNINGS ÑÑTo prevent injury or fire, take ÑÑHow To Reset Your Unit • If the unit or the connected unit fails to operate properly, reset the unit.1 Press the button.The unit returns to factory settings. the following precautions: • To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit. • Do not watch or fix your eyes on the unit’s display when you are driving for any extended period.
Basic Operations Basic Operations Functions of the Buttons on the Front Panel 1 Turning on the Unit The method of turning on is different depending on the model. 1 Press the [HOME] button. 2 3 4 5 hh The unit is turned on. 6 ●● To turn off the unit: NOTE • The panels shown in this guide are examples used to provide clear explanations of the operations. For this reason, they may be different from the actual panels. Name 1 Press the [HOME] button for 1 second.
Basic Operations Getting Started ■■ [Camera] Set the parameters for the camera. 1 Touch [Camera]. 2 Set each item and touch [ ]. For detailed operation, see Instruction Manual. Initial setup Perform this setup when you use this unit first time. 1 ■■ [DEMO] Set the demonstration mode. Default is “ON”. 1 Touch [DEMO] and set [ON] or [OFF]. Set each item as follows. 2 ■■ [Language] Select the language used for the control screen and setting items. Default is “[American English(en)]”.
Basic Operations 3 Touch [User Interface]. Adjusting the volume To adjust the volume (0 to 40), Press [R] to increase, and press [S] to decrease. Holding [R] increases the volume continuously to level 15. hh User Interface screen appears. 4 Touch [Clock Adjust]. Touch screen operations To perform operations on the screen, you need to touch, touch and hold, flick or swipe to select an item, display setting menu screen or to change the page, etc.
Basic Operations HOME screen descriptions Most functions can be performed from the HOME screen. 1 2 Source selection screen descriptions You can display all playback sources and options on the source selection screen. 1 3 4 5 1 • Displays the control screen of current source. 2 • Current source information 3 • Displays the source selection screen. (P.9) 4 • Short-cut playback source icons (P.10) 5 • Displays the Hands Free screen. (P.
Basic Operations Select the playback source Put the unit in standby 1 1 Touch [ 2 Touch [STANDBY]. Touch [ ] on the HOME screen. From the screen, you can select the following sources and functions. ] on the HOME screen. • Switches to the USB Mirroring screen from the connected Android smartphone. It is necessary to connect Android smartphone with “Mirroring OA for KENWOOD” application installed and to set [Mode] to [Mirroring for Android™].
Basic Operations Source control screen descriptions 4 [Û] Touch to display the Hands Free screen. (P.18) When connecting as Apple CarPlay or Android Auto, it works as a phone provided in Apple CarPlay or Android Auto. There are some functions which can be operated from most screens. Indicators 1 2 3 4 Sub menu 1 [ ]/[ ] Connected Bluetooth device information. 2 All sources icon Displays all sources. 3 Secondary screen • [ ]/[ ] : The Secondary screen changes every time you touch it.
Basic Operations MENU screen 1 Press the [MENU] button. List screen There are some common function keys in the list screens of most sources. 1 2 6 hh MENU screen appears. 2 Touch to display the MENU screen. 3 4 5 1 Displays list type selection window. The contents of the menu are as follows. 2 • Displays the SETUP Menu screen. Displays music/movie file list. • Displays the APP (Apple CarPlay/ Android Auto) screen. Scrolls the displayed text. • Displays the Screen Adjustment screen.
USB USB Connecting a USB device 1 Connect the USB device with the USB cable. (P.26) USB Basic Operation Most functions can be controlled from the source control screen and playback screen. Control screen 1 2 3 4 Press the [HOME] button. Touch [ ]. Touch [USB]. (P.10) ÑÑDisconnect the USB device 1 2 3 4 2 Press the [HOME] button. Touch [ ]. Touch a source other than [USB]. Detach the USB device. ÑÑUsable USB device You can use a mass-storage-class USB device on this unit.
Radio Radio Radio Basic Operation 3 Operation keys Most functions can be controlled from the source control screen. To enter Radio source, touch [Radio] icon in the source selection screen. (P.10) Control screen 4 Preset list • Touch on the right side of the screen to display the Preset list. Touch again to close the list. • Recalls the memorized station. • When touched for 2 seconds, stores the current receiving station in memory. 4 1 • [E] [F] : Tunes in a station.
SiriusXM® Radio Memory Operation ÑÑAuto memory You can store stations with good reception in memory automatically. 1 2 Touch desired band key. Touch [ ] on the left side of the screen. Touch [AME]. SiriusXM® (DMX4707S/ DMX47S) SiriusXM® Basic Operation Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio.
SiriusXM® Control screen 3 Artwork / Function panel 1 2 3 5 4 Open the drawer 3 • Displays the album artwork for most SiriusXM music channels. • Touch [ ] of the screen to display the function panel. Touch [ ] to close the panel. –– [Direct Channel]: Touch and enter the desired number. For details, see Instruction Manual. –– [SETUP]: Touch to display the SiriusXM SETUP screen. For details, see Instruction Manual. –– [Replay/Live]: Touch to turn on or off the replay mode. See Instruction Manual.
Bluetooth Control Bluetooth Control ÑÑAbout the cell-phone and Bluetooth audio player This unit conforms to the following Bluetooth specifications: Version Bluetooth Ver. 4.
Bluetooth Control 7 Touch [Select Device] in the Bluetooth SETUP screen. Using Hands-Free Unit You can use telephone function by connecting the Bluetooth telephone to this unit. NOTE • While Apple CarPlay or Android Auto is being connected, Bluetooth Hands-Free function cannot be used. Only Apple CarPlay or Android Auto Hands-Free function can be used. 8 Touch [ ] you want to connect. ÑÑMake a call 1 Touch [TEL] / [Û]. hh Hands Free screen appears. 2 NOTE Select a dialing method.
Bluetooth Control Call using call records Call using the preset number 1 2 1 2 Touch [ ]. Select the phone number from the list. Touch [ ]. Touch the Name or phone number. Call by entering a phone number Call using the phonebook 1 2 1 2 3 Touch [ ]. Enter a phone number with number keys. Touch [ ]. 3 Touch [ ]. Select the person you want to call from the list. Select the phone number from the list.
Bluetooth Control ÑÑReceive a call 1 ÑÑOperations during a call Touch [ ] to answer a phone call or [ to reject an incoming call. ] ●● Adjust the receiver volume Press the [S] or [R] button. NOTE • While monitoring the view camera, this screen does not appear even if a call comes in. To display this screen, return the shift knob of car to the driver position. To end call 1 While talking, touch [ ]. ●● Output the dial tone Touch [DTMF] to display the tone input screen.
Controlling Audio Controlling Audio You can adjust the various settings such as audio balance or subwoofer level. 1 2 Press the [MENU] button. hh MENU screen appears. Touch [ ]. ÑÑControlling General Audio 1 2 Press the [MENU] button. hh MENU screen appears. Touch [ ]. hh Audio screen appears. 3 Touch [Fader / Balance]. 4 Set each item as follows. ■■ [Fader] / [Balance] Adjust the volume balance around the touched area. [C] and [D] adjust the right and left volume balance.
Controlling Audio ÑÑEqualizer Control You can adjust equalizer by selecting the optimized setting for each category. 1 2 3 4 ■■ [SW Level] Adjusts the subwoofer volume. Press the [MENU] button. hh MENU screen appears. Touch [ ]. hh Audio screen appears. Touch [Equalizer]. Touch the screen and set the Graphic Equalizer as desired. ■■ [ALL SRC] Apply the adjusted equalizer to all sources. Touch [ALL SRC] and then touch [OK] on the confirmation screen.
Connection/Installation Connection/Installation Before Installation Before installation of this unit, please note the following precautions. # WARNINGS • If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. • Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow).
Connection/Installation ÑÑSupplied accessories for Installing the unit installation 1 ÑÑNon-Japanese cars 2 (Except DMX5020S) (3 m) x1 x1 3 4 (2 m) x1 5 x1 (M5 × 6 mm) (M5 × 8 mm) x6 7 x6 8 x1 9 NOTE x1 [1] x2 [1] Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. 6 E xcept DMX5020S • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip).
Connection/Installation ÑÑMicrophone unit ÑÑRemoving the unit 1) Check the installation position of the microphone (accessory 1). 2) Clean the installation surface. 3) Remove the separator of the microphone (accessory 1), and stick the microphone to the place shown below. 4) Wire the microphone cable up to the unit with it secured at several positions using tape or other desired method. 5) Adjust the direction of the microphone (accessory 1) to the driver.
Connection/Installation ÑÑConnecting wires to terminals Connect to vehicle’s steering remote harness. Contact your KENWOOD dealer for details. (DMX5020S only) ST REMOTE INPUT 1 Bright Green/Red ST REMOTE INPUT 2 Purple/Red ST REMOTE GND Gray/Red STEERING WHEEL REMOTE INPUT Light Blue/Yellow (Steering remote control wire) To steering remote To use the steering wheel remote control feature, you need an exclusive remote adapter (not supplied) matched to your car. USB terminal[1] (1.0 m) 5V=1.
Connection/Installation ÑÑConnecting an iPhone/Android Micro USB to USB cable[2] Android smartphone[2] 1 3 5 7 2 4 6 8 iPhone[2] Lightning connector 1 3 5 7 2 4 6 8 KCA-iP103 (0.8m)[3] Accessory 7 Accessory 8 Speaker impedance: 4-8 Ω White USB terminal[1] (1.0 m) To front left speaker White/Black 5V=1.5A Cap Gray To front right speaker Gray/Black Green To rear left speaker Green/Black Purple To rear right speaker Purple/Black P.
Appendix Appendix Specifications ■■Bluetooth section Frequency : 2.402 – 2.480 GHz RF Output Power (E.I.R.P.) : +8 dBm (Avg.), Power Class 1 ■■General Operating Voltage : 12V DC Car Battery Speaker Impedance :4–8Ω Specifications subject to change without notice. About this Unit ■■Copyrights • The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by JVCKENWOOD Corporation is under license.
Appendix • THIS PRODUCT IS LICENSED UNDER THE MPEG‑4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (¡) ENCODING VIDEO IN COMPLIANCE WITH THE MPEG‑4 VISUAL STANDARD (“MPEG-4 VIDEO”) AND/ OR (¡¡) DECODING MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE MPEG-4 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE.
Supplier’s Declaration of Conformity Trade Name: KENWOOD Products: MONITOR WITH RECEIVER Model Name: DMX4707S / DMX47S Responsible Party: JVCKENWOOD USA CORPORATION 2201 East Dominguez Street, Long Beach, CA 90810, U.S.A. PHONE: 310 639-9000 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
!B5H-0358-20_QSG_DMX_KR_EnEsFr.
INFORMATION/ INFORMACION English Updated information (the latest system updates, instruction manual, new functions, etc.) is available from < https://www.kenwood.com/cs/ce/> Fran~ais Des informations actualisees (le dernier mode d'emploi, les mises ajour du systeme, les nouvelles fonctions, etc.) sont disponibles sur Espanol Encontrara la informaci6n actualizada (el manual de instrucciones mas reciente, actualizaciones del sistema, nuevas funciones, etc.
KENWOOD Important Notice on Software [i Software License on This Product The software embedded in this product comprises a EULA [i Software License Agreement JVCKENWOOD Corporation (hereinafter called number of independent software components, each "Licensor") holds either the copyright to the of which is copyrighted by JVCKENWOOD Corporation embedded software or the right to sublicense it. This or by a third party.
JVCKENWOOD Corporation Article 3 (Terms of License) Article 8 (Cancellation of the Agreement) 1.
Units purchased lhrough the U.S.A. military exchange service overseas may be serviced under warranty in the continenlal U.S.A., subiect to the following conditions. 1) The original warranty is in elfect. 2) Proof of purchase is provided to the servicer. Any and all implied warranties, including warranties ol merchantability and titness tor a particular purpose, shall be limited in duration to the lenglh of this warranty.
JVCKENWOOD Canada Inc. JVCKENWOOD USA Corporation This warranty will be honored only mlhe U.S.A WHO IS PROTECTED This warranty is eolorceable only by the original purchaser KENWOOD LIMITED WARRANTY FOR CAR STEREO COMPONENTS WHAT WE WILL PAY FOR We will pay for all labor and material expenses lor covered ilerns.