Instruction Manual

ManualsBrandsKenwood USA ManualsElectronics800 MHz APCO P25 Transceiver

Table Of Contents

INSTRUCTION MANUAL
- _
  - NOTICES TO THE USER
    - _
      - FCC WARNING
  - UNPACKING AND CHECKING EQUIPMENT
    - Installing the Belt Clip
    - Installing the Optional KMC-25 Speaker/ Microphone
      - _
        ◆?Key Lock

KENWOOD CORPORATION

FCC ID: ALH33063110

INSTRUCTION MANUAL

TK-5400:

THANK YOU!

We are grateful you chose

KENWOOD

for your land mobile radio applications. We believe this easy-to-use transceiver

will provide dependable communications to keep personnel operating at peak efficiency.

KENWOOD

transceivers incorporate the latest in advanced technology. As a result, we feel strongly that you will be

pleased with the quality and features of this product.

NOTICES TO THE USER

WARNING:

◆

◆◆

◆

GOVERNMENT LAW PROHIBITS THE OPERATION OF UNLICENSED RADIO TRANSMITTERS WITHIN THE

TERRITORIES UNDER GOVERNMENT CONTROL.

◆

◆◆

◆

ILLEGAL OPERATION IS PUNISHABLE BY FINE OR IMPRISONMENT OR BOTH.

◆

◆◆

◆

REFER SERVICE TO QUALIFIED TECHNICIANS ONLY.

◆

◆◆

◆

DO NOT OPERATE YOUR TRANSCEIVER IN EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, ETC.).

◆

◆◆

◆

TURN OFF YOUR TRANSCEIVER WHILE TAKING ON FUEL, OR WHILE PARKED IN GASOLINE SERVICE

STATIONS.

SAFETY:

It is important that the operator is aware of and understands hazards common to the operation of any transceiver.

WARNING:

EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.)

Turn off your transceiver while taking on fuel, or while parked in gasoline service stations.

One or more of the following statements may be applicable:

FCC WARNING

This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause

harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the

authority to operate this equipment if an unauthorized change or modification is made.

INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following measures:



Reorient or relocate the receiving antenna.



Increase the separation between the equipment and receiver.



Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.



Consult the dealer for technical assistance.

Summary of content (10 pages)

PAGE 1
KENWOOD CORPORATION FCC ID: ALH33063110 INSTRUCTION MANUAL TK-5400: THANK YOU! We are grateful you chose KENWOOD for your land mobile radio applications. We believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency. KENWOOD transceivers incorporate the latest in advanced technology. As a result, we feel strongly that you will be pleased with the quality and features of this product.
PAGE 2
KENWOOD CORPORATION FCC ID: ALH33063110 ATTENTION (U.S.A. Only): The RBRC Recycle seal found on KENWOOD nickel-cadmium (Ni-Cd) battery packs indicates KENWOOD’s voluntary participation in an industry program to collect and recycle Ni-Cd batteries after their operating life has expired. The RBRC program is an alternative to disposing Ni-Cd batteries with your regular refuse or in municipal waste streams, which is illegal in some areas.
PAGE 3
KENWOOD CORPORATION FCC ID: ALH33063110 Installing/ Removing the Optional Battery Pack PREPARATION The battery pack is not charged at the factory; charge it before use. CAUTION: ◆ DO NOT RECHARGE THE BATTERY PACK IF IT IS ALREADY FULLY CHARGED. DOING SO MAY CAUSE THE LIFE OF THE BATTERY PACK TO SHORTEN OR THE BATTERY PACK MAY BE DAMAGED. ◆ AFTER RECHARGING THE BATTERY PACK, DISCONNECT IT FROM THE CHARGER.
PAGE 4
KENWOOD CORPORATION Installing the Antenna Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure. Installing the Belt Clip If necessary, attach the belt clip using the two supplied 3 x 6 mm screws. Note: If the belt clip is not installed, its mounting location may get hot during continuous transmission or when left sitting in a hot environment.
PAGE 5
KENWOOD CORPORATION FCC ID: ALH33063110 Installing the Optional KMC-25 Speaker/ Microphone 1 Insert the guide of the speaker/ microphone connector into the groove of the universal connector. 2 Secure the connector in place using the attached screw. GETTING ACQUAINTED Knob NO． 1 Lock/ Non Lock Name Power switch/ Lock/ Non Lock Volume control 2 Selector Lock Description Power SW (CCW：Power OFF) Audio Volume adjuster Mechanical stopper Switch Power switch/Volume control Selector LED LCD Fig.
PAGE 6
KENWOOD CORPORATION FCC ID: ALH33063110 ＜Top > NO． Name 1 Toggle SW 2 Top 1 3 Top 2 Lock/ Non Lock Description Programmable default：No Function Non Lock Programmable default：No Function Non Lock Programmable default：No Function Lock ＜Left side＞ NO． Name Lock/ Non Lock Description 1 PTT Non Lock TX ON/OFF 2 Side 1 Non Lock Programmable default：No Function 3 Side 2 Non Lock Programmable default：No Function 4 Orange Non Lock Programmable default：No Function ＜Front＞ NO
PAGE 7
KENWOOD CORPORATION FCC ID: ALH33063110 4.3.2 LCD Fig.
PAGE 8
KENWOOD CORPORATION FCC ID: ALH33063110 TERMINAL Universal connector connector cover for blindfold mode of resin is possible． NO． Name Description I/O 1 2 SSW SP+ EXT/INT SP switch input BTL output ＋ for external speaker I O 3 SPMSW/CTS BTL output − for external speaker O I 5 6 7 8 9 10 11 12 EMC EME PTT REM RTS E 5M TXD EXT/INT MIC switch input Clear To Send External microphone input External microphone earth PTT input Programmable function key input Request To Send Earth 5V output Serial d
PAGE 9
KENWOOD CORPORATION FCC ID: ALH33063110 Appearance Appearance without 12key Pad (with KNB-17A) Appearance with 12key Pad (with KNB-17A)
PAGE 10
KENWOOD CORPORATION FCC ID: ALH33063110 OPERATING BASICSATING BASICS ◆ Switching Power ON/OFF Turn the Power switch/ Volume control clockwise to switch the transceiver ON. Turn the Power switch/ Volume control counterclockwise to switch the transceiver OFF. ◆ Adjusting the Volume Rotate the Power switch/ Volume control to adjust the volume. You can adjust the volume to one of six levels. Clockwise increases the volume and counterclockwise decreases it. • The selected volume level appears on the display.