Use & Care / Installation Manual Manual de Uso y Cuidado / Instalación English / Español Models / Modelos 233.5817*, 233.5818* Kenmore Elite Range Hood ® Campana de cocina * = color number, número de color SV07328 rev. D Sears Brands Management Corporation, Hoffman Estates, IL 60179 USA www.kenmore.com www.sears.
READ AND SAVE THESE INSTRUCTIONS TABLE OF CONTENTS KENMORE LIMITED WARRANTY Warranty .........................................................................2 Safety Instructions ..........................................................3 Operation ........................................................................4 Cleaning ...........................................................................4 Parts Included With Hood .............................................
SAFETY INSTRUCTIONS ! INTENDED FOR DOMESTIC COOKING ONLY ! CAUTION ! 1. For indoor use only. 2. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. 3. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit. 4. Your hood motor has a thermal overload which will automatically shut off the motor if it becomes overheated. The motor will restart when it cools down.
OPERATION OPERATION Always turn ON your hood before you begin cooking in order to establish an air flow in the kitchen. Let the blower run for a few minutes to clear the air after you turn off the range. This will help keep the whole kitchen cleaner and brighter. Filter maintenance indicator After 24 hours of operation, the filter maintenance light indicator will start blinking. This indicates the filters need to be cleaned in order to maintain efficient operation of the unit.
PARTS NOT INCLUDED WITH HOOD NOTE Before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the manufacturer. Ducting Accessories are not included with hood. (See “Equivalent Duct Length Chart” on page 6 for Ducting Accessory Model Nos.) Warranty PARTS INCLUDED WITH HOOD 120 V, 50 W, MR16 with GU10 base or PAR 16 with GU10 base, shielded halogen lamps (4 per hood). Sears Part No.
EQUIVALENT DUCT LENGTH CHART Kenmore range hoods are designed to perform efficiently when attached to long runs of duct. As a point of reference, this hood will function at approximately 80% of its rated air performance when 100 equivalent feet of 7” round ductwork is attached. Use this chart to calculate the equivalent duct length of your system. Broan Model 428 3¼” x 10” Right-angle Elbow Equivalent length 8.5 ft. HJ0058 Sears Model 59691 6” Round Wall Cap Equivalent length 34 ft. (6 ft.
INSTALL DUCTWORK Roof cap Warranty 1. Plan where and how the ductwork will be located. Install proper-sized ductwork, transition(s), elbow(s), and roof or wall cap. For best results, use a minimum number of transitions and elbows. Use 2’’ metal foil duct tape to seal duct joints. The minimum hood distance above cooktop must not be less than 24’’. A maximum of 30’’ above cooktop is highly recommended for best capture of cooking impurities. Distances over 30’’ are at the installer and users discretion.
PREPARE THE HOOD 1. Punch-out the knock-out for the chosen opening (horizontal at the back or vertical on top of the hood) and for electrical connection. VERTICAL DISCHARGE HORIZONTAL DISCHARGE HD0164 HD0165 2. Pull latch tab and remove both filters from the hood. HD0166 SCREW LOCATIONS 3. Remove the 5 screws retaining the bottom panel to the hood and set aside. Pull out the bottom panel by the front part.
PREPARE THE HOOD Warranty 4. Unplug both light connectors mounted on each side panels. See picture beside. Safety HE0075 6. Then lift the front of the side panel. 7. Pull out the side panel tabs (B) from the hood and remove the side panel. Cleaning A Operation 5. To remove side panel, hold it near the front of the hood and slide in the same direction as the small arrow (A) in order to disengage it.
PREPARE THE HOOD VERTICAL DISCHARGE HORIZONTAL DISCHARGE 1 1 HO0084 HO0082 8. Using 2 no. 6 x 1/2’’ screws, assemble the adapter/damper to the hood. NOTE: Damper flap pivot (1) to the front of the hood for vertical discharge and for horizontal discharge, damper flap pivot to top of hood. HO0083 HO0085 9. Seal the adapter/damper to the hood using duct tape. INSTALL THE HOOD 1. Run power cable to installation location. Position the hood in its intended location.
CONNECT THE WIRING Safety 1. Connect cable using provided wire connectors. Connect BLACK to BLACK, WHITE to WHITE and GREEN or bare wire under GREEN ground screw. DO NOT FORGET TO CONNECT THE GROUND. Warranty WARNING: Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with all applicable codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting means to prevent power from being switched on accidentally.
SERVICE PARTS 1 3 2 10 9 6 7 4 REPLACEMENT PARTS AND REPAIRS In order to ensure your unit remains in good working condition, you must use the manufacturer genuine replacement parts only. The manufacturer genuine replacement parts are specially designed for each unit and are manufactured to comply with all the applicable certification standards and maintain a high standard of safety.
Get it fixed, at your home or ours! Your Home For troubleshooting, product manuals and expert advice: www.managemylife.com For repair – in your home – of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner’s manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters.