OWNER'S MANUAL 0 l o Premier Reverse Osmosis Drinking Water System MODEL _W _O _o _m _m NO. 625.385560 0 Caution: Read and follow all safety rules and operating • Warranty instructions before first use of this product. • Installation Questions • How It Works ? Visit www.KenmoreWater.com or call toll free 1-800-426-9345 Repair (M - F, 7 AM - 6 PM CST) or Parts ? Call toll free 1-800-469-4663 See back • Care Of • Specifications cover for other Sears service numbers.
KENMORE When installed, operated a defect in material to arrange ELITE ONE YEAR FULL WARRANTY and maintained or workmanship if repair proves impossible). does not cover the filter cartridges able items that can wear to all supplied instructions, if this product fails due to within one year from the date of purchase, call 1-800-4-MY-HOME for free repair (or replacement This warranty according out from normal or the reverse osmosis membrane, use within the warranty which are expend- period.
Unpack and Check Shipment ...................................................................... 4 What Your Reverse Osmosis System Will do ........................................................... Plan Your Installation ........................................................................... Overview and Site Preparation Step I-Install Supply Water 5 5-6 ..................................................................... Fitting 7 ........................................................
INSPECT SHIPMENT Your Reverse Osmosis complete Drinking Water in one carton. System is shipped Remove all items from your ship- ping carton. Check all items against the packing items lost or damaged the shipping carton. in shipment. for the part numbers of missing or damaged plumber names and exist, listed through- bag until you are ready NOTE: Codes in the state of Massachusetts lation by a licensed saddle valves. to view and parts items.
Your Reverse Osmosis treatment natural physical is forced process through and impurities faucet with are filtered while RO waste measured in water cartridges. ticles, other before osmosis. Water, minerals it can enter any tastes and/or reduces that minerals goes to the are sent to the the RO membrane, To prevent (TDS).
Typical Under Sink Installation All install parts included in package. Drain Adapter for Reverse Osmosis Waste Water Reverse Osmosis Assembly Figure 2 Typical Remote Installation Outside (Hard Faucet Water) Outside (Hard Soft, Cold To Faucet Water) Water Reverse Osmosis Air Gap Faucet Soft, Hot Soft, Cold Water Sediment Filter_ Reverse Osmosis System Storage Tank Water Meter Water Softener Additional Air Gap Main Shutoff It Valve Parts required.
OVERVIEW There are seven easy steps to installing your Drinking Water system. They are as follows: STEP 1 - Install Cold Water Supply fitting STEP 2 - Install Drain Adapter STEP 3 - Install Reverse Osmosis Assembly STEP 4 - Install Storage Tank STEP 5 - Install Reverse Osmosis Faucet STEP 6 - Connect Tubing STEP 7 - Sanitize, Pressure Test, Purge System These steps are explained in detail over the next few to read through the entire manual pages. It is recommended before beginning ly.
CHOOSE TYPE OF WATER FITTING TO INSTALL Check and comply codes as you with local plumbing plan, then install a cold feed (supply) to the Specifications The fitting 1/4" page must provide tubing. A typical supply fitting water fitting. for supply water a leak-tight connection requirements. connection to the RO using the included is shown in Figure 5.. An optional using standard plumbing Refer fittings water connection (not included) is shown in Figure 5B.
Under The Sink Installation INTRODUCTION A suitable drain point is needed for the reject water the Reverse Osmosis Filter. You have two options choose from: • Install the Drain Adapter from to Single trap J included with your unit See Figures 6, 7 & 8. This is used in under the sink installations. The drain adapter kit is installed onto your sink drain Double Trap pipe above Drain !_ the P-trap. See Figure 6.
Outside (Hard Faucet Outside Faucet Water) BLUE Tubing to Reverse Osmosis Air (Hard Water) Soft, Cold Water Gap Faucet Soft, Hat Water Line Soft, Cold GREEN Tubing to Reverse Osmosis System Remote Location Sediment Filter Reverse Installation Osmosis YELLOW Tubing to TankStorage I Storage Tank Water Meter Water Heater Main Shutoff Valve c_ Sump Figure 9 I--I Air_ap W2" Floor Stand pipe INSTALL Laundry Tub Airgap A REMOTE DRAIN POINT AND Drain AIR GAP (Remote Location) You
INSTALLREVERSE OSMOSISFILTER ASSEMBLY The Reverse Osmosis Filter Assembly on its side. When planning allow adequate back of the Reverse Osmosis assembly the monitor tubing battery. can sit upright your installation, or lay you need to lengths to be able to access the in order to change See Figure 11. Figure 11 INSTALL STORAGE TANK Jr Jj 1. Apply thread sealing tape to the threads at the top of the tank (max. 2. Locate the tubing tor with a wrench connector. 2 wraps).
SELECT LOCATION MOUNTING OF REVERSE OSMOSIS FAUCET HOLE faucet You will need to select the location of the Reverse Osmosis Faucet. You have three options ° Use the existing to choose from: sink top hole for the spray soap dispenser (Must be 1-1/4" ° Drill a new hole in the sink hose or in diameter) ° Drill a new hole in the countertop next to the sink 1. Determine where you are going to install your Reverse Osmosis Faucet. 2. Check to ensure the Reverse Osmosis faucet flat against 3.
NOTE: If you ran the red reverse osmosis drain tubing directly to a remote drain and refer to instructions 7. Mount the faucet point, disregard on page body steps 5 and 6 10. on to the faucet base, 1/4 turn. jJ BLACK TUBE FAUCET ELECTRONICS The RO system will monitor the total product the unit and also length of time the filters installed.
HOW TO CUT AND CONNECT Your Reverse Osmosis Water tings for quick tubing instructions before THE TUBES System includes push-in fit- connection. connecting Review the following the tubes in the next step. Cut tubes to length 1. Use a sharp cutter Always or knife to cut the end of tubing. cut the tubing square. 2.
NOTE: back 3/8" black tubing Tubing lengths NOTE: access to the for servicing. Codes in the state of Massachusetts installation by a licensed the use of saddle 211 should allow of the assembly plumber valves. and require do not permit If you live in the state of ii Massachusetts, red tubing the Commonwealth ceeding blue water supply review plumbing code 248-CMR of Massachusetts before of pro- with the installation.
SANITIZETHESYSTEM Sanitizing is recommended immediately after installation of the Reverse Osmosis system. It's also recommended after servicing inner parts. It is important installing or servicing handling inner parts of the system. Complete that the person the system have clean hands while the following steps to sanitize ! the system. See Figure 22. 1. Turn off the water tem. 2. Open supply to the Reverse Osmosis sys- the Reverse Osmosis faucet. already empty, allow the water 3.
PRESSURE TESTTHESYSTEM NOTE: Complete ing page the sanitizing before Reverse procedures Osmosis Faucet on the preced- pressure testing. kitchen To pressure test the system, complete 1. Open the water the following faucet_ __ steps. supply valve to the Reverse Osmosis System. See Figure 23. 2. Open the main water faucets. supply valve and several house This will purge air from the house plumbing and system. Close faucets when water runs smooth. See Figure 23. 3.
HOW YOUR REVERSE OSMOSIS SYSTEM WORKS Introduction: Your Reverse Osmosis (RO) Drinking System uses your household through three filters. out. Delicious tank-ready tasting water Minerals and impurities drinking water for your use. Minerals clown the drain. The following Prefilter: Water paragraphs Water in System from the cold supply pipe enters the pre- ment cartridge sediments, are sent will explain Drinking filter. See Figure 24.
PRODUCT WATER FAUCET Fq air PRODUCT WATER dgravity rain WASTE WATER AUTOMATIC drain flow SHUTOFF control check valve \ O WATER iN GREEN i BLUE t_ PREFILTER POSTFILTER t t IL RED RO MEMBRANE "_ YELLOW IN Reverse Osmosis Water Flow Schematic Figure 24 Water Flow Description 1. Water enters prefilter. Sand, silt and other sediments 2. Water leaves prefilter and proceeds 3. Water enters the Reverse Osmosis membrane. 4. Processed water 5. Waste water are reduced.
PREFILTER/POSTFILTER MAINTENANCE Cover NOTE: It is recommended to replace the battery, prefilter and postfilter cartridges at least every 6 months of product water use. Replace with sediments. The prefilter more often and postfilter if they begin to plug are replaceable sediment carTurn to the left tridges with activated carbon in its composition. See Figure 25. You must periodically replace the prefilter and postfilter cartridge.
CHANGE COLLET AND O-RING 1. Remove the collet small screwdriver. 3. Push the collet 27 & 28. then seal into follow with bottom of collet. _/_}\ 1 Fitting port. See Figures 27 & 28. port, lubricate into the bottom port and o-ring from the fitting with a Be careful not to scratch the internal walls of the collet 2. Clean collet Push o-ring and insert the o-ring seal Cotlet of the port. See Figures 27 & 28. inward Change collet and o-ring until it locks in place.
Supply water pressure limits ................................................ Supply water temperature Maximum total dissolved Maximum water Maximum Chlorine Supply supply hydrogen water, Percent rejection of TDS, minimum shutoff Efficiency 2000 ...................................................... 0 .......................................................... 2.0 24 hours ' control 4-10 ............................................... (new membrane) 18.4 gal. (69.6 liters) _ .....
Questions? Call The I
Cause: The level of chlorine supply exceeds has destroyed in your water maximum limits, Correction: If the water and the Reverse Osmosis needed. membrane. Cause: Cause: is no longer from Postfilter the water Correction: Contamination storage this condition Correction: membrane in product Replace before postfilter See page water Correction: the post filter Use sanitizing tank. See pages Cause: System contamination.
Cause: Drain tubing) side of faucet plugged, ly connected to drain Cause: Battery dead. Cause: Battery installed ] _lem_ airgap restricted (3/8" black I Correction: or incorrect- point. I Inspect and eliminate instructions for proper restriction drain or plug. Refer to installation connection. incorrectly. Correction: Replace Correction: Install with battery new battery. correctly.
Manifold Housing PUSH-IN FITTINGS 18 o-ring 19 seat o©. _ coltet 2 i I I 2O 15 I 11 I 14 22--_ \ 1/4" red tubing 24 \ \ Questions? 26 "4 Call f The Kenmore 13 Water Line 1-800-426-9345 25 or visit KenmoreWater.
Key No. Part No.
Your Home For expert troubleshooting and home solutions advice: managemylife Our Home For repair of carry-in items like vacuums, lawn equipment, and electronics, call anytime for the location of your nearest Sears Parts & Repair Service 1-800-488-1222 (U.S.A.) 1-800-469-4663 www.sears.com To purchase agreement (U.S.A.) Para pedir servicio de reparaci6n a domicilio, y para ordenar piezas: 1-888-SU-HOGAR on a product serviced 1-800-361-6665 Au Canada ® (1-888-784-6427) www.sears.