KW5813 ADSL Wireless N Router User Manual User Manual
ADSL Router User Manual NOTICE This document contains proprietary information protected by copyright, and this Manual and all the accompanying hardware, software, and documentation are copyrighted. All rights are reserved. No part of this document may be photocopied or reproduced by mechanical, electronic, or other means in any form.
ADSL Router User Manual Content 1 OVERVIEW ................................................................................................................................... 2 1.1 FEATURES ........................................................................................................................... 2 1.1.1 Data rate ...................................................................................................................... 2 1.1.2 ADSL Compliant ...................................
ADSL Router User Manual 1 Overview Thank you for choosing our product. The KW5813 ADSL Wireless N router combining an ADSL modem, an 802.11n wireless router and a 4-port switch in one unit, bringing high-speed wireless Internet connection to a home or an office. 1.1 Features 1.1.1 Data rate Downstream data rate up to 24Mbps, Upstream data rate up to 1Mbps 1.1.2 ADSL Compliant ITU G.992.1 (G.DMT) ITU G.992.2 (G.Lite) ITU G.994.1 (G.hs) ITU G.992.3 (G.DMT.BIS) ITU G.992.4 (G.lite.
ADSL Router User Manual IP Static Routing Routing Information Protocol (RIP, RIPv2) Network Address Translation (NAT) Virtual Server, Port Forwarding Dynamic Host Configuration Protocol (DHCP) DNS Relay, DDNS IGMP Proxy Simple Network Time Protocol (SNTP) VPN pass-through (IPSec/PPTP/L2TP) Parent control 1.1.5 ATM Capabilities RFC 1483 Multi-protocol over ATM “Bridged Ethernet” compliant RFC 2364 PPP over ATM compliant RFC 2516 PPP over Ethernet compliant ATM Forum UNI3.1/4.
ADSL Router 1.1.7 1.1.8 1.1.9 1.
ADSL Router 1.3 User Manual System Requirements Before using this ROUTER, verify that you meet the following requirements: Subscription for ADSL service. Your ADSL service provider should provide you with at least one valid IP address (static assignment or dynamic assignment via dial-up connection). One or more computers, each contains an Ethernet 10/100M Base-T network interface card (NIC). A hub or switch, if you are connecting the device to more than one computer.
ADSL Router User Manual 2 Hardware Description Front Panel LED PWR LAN1,2,3,4 Color Function Solid Green Power on Off Power off On: LAN link established and active via LAN port Blinking: DSL data activity occurs. Off: No LAN link via LAN port Green On: The wireless module is ready and idle.
ADSL Router User Manual Rear panel Port Function DSL Connect the device to an ADSL telephone jack or splitter using a RJ-11 telephone cable ETH1,2,3,4 Connect the device to your PC's Ethernet port, or to the uplink port on your hub/switch, using a RJ-45 cable ON/OFF Switch it on or off POWER Connect to the supplied power adapter Side panel WIFI button: Enable or disable wireless function. Reset button: System reset or reset to factory defaults. WPS button: A convenient way for WPS set.
ADSL Router User Manual 3 Hardware Installation This chapter shows you how to connect Router. Meanwhile, it introduces the appropriate environment for the Router and installation instructions. 1. Using a telephone line to connect the DSL port of ROUTER to the MODEM port of the splitter, and using a other telephone line connect your telephone to the PHONE port of the splitter, then connect the wall phone jack to the LINE port of the splitter.
ADSL Router User Manual 4 PC Configuration Guide 4.1 Local PC Configuration in Windows 95, 98, ME, XP 1. In the Windows task bar, click the “Start” button, point to “Settings”, and then click “Control Panel”. 2. Double-click the “Network” icon. 3. On the “Configuration” tab, select the TCP/IP network associated with your network card and then click “Properties”. 4. In the “TCP/IP Properties” dialog box, click the “IP Address” tab. Set the IP address as 192.168.1.
ADSL Router User Manual 5 Web-based Management Guide In order to use the web-based management software it will be necessary to use a computer that occupies the same subnet as the Router. The simplest way to do this for many users will be to use DHCP server that is enabled by default on the Router. 5.1 LAN setting page Launch a web browser, such as Internet Explorer, and then use http://192.168.1.1 to log on to the setting page.
ADSL Router We can select User Manual wizard setup or advanced setup mode to setup KW5813.the wizard set up will guide us for a basic setting,and the advanced setup will guide us to home page for more detailed setup. 5.2 Internet Access Configuration 5.2.1 ADSL Mode Setup From home page, you can find Advanced Setup option on the left router configuration page. 1. From Layer2 Interface, click ATM Interface. you can set it up according to the following steps.
ADSL Router User Manual 4. Click Add to select a layer 2 interface for this service and then click Next. 5. Choose WAN service type, just choose PPPoE for example here. You can enter your own service description here if you want and then click Next. 6. Input PPP Username & PPP Password and then click Next. The user interface allows a maximum of 256 characters in the user name and a maximum of 32 characters in the password.
ADSL Router User Manual PPPoE service name can be blank unless your Internet Service Provider gives you a value to enter. Authentication method is default to Auto. It is recommended that you leave the Authentication method in Auto, however, you may select PAP or CHAP if necessary. The default value for MTU (Maximum Transmission Unit) is 1500 for PPPoA and 1492 for PPPoE. Do not change these values unless your ISP asks you to.
ADSL Router User Manual The gateway can be configured to disconnect if there is no activity for a specific period of time by selecting the Dial on demand check box and entering the Inactivity timeout. The entered value must be between 1 minute and 4320 minutes. The PPP IP Extension is a special feature deployed by some service providers. Unless your service provider specifically requires this setup, do not select it.
ADSL Router User Manual 8. Get DNS server information from the selected WAN interface or enter static DNS server IP addresses. If only a single PVC with IPoA or static MER protocol is configured, you must enter static DNS server IP addresses. 9. Make sure that the settings below match the settings provided by your ISP. Click on the Apply/Save button to save your configurations. 5.2.2 Router Mode Setup 1. From Advanced Setup, click Layer2 Interface and select ETH Interface.
ADSL Router User Manual 2. Click Add and you’ll see the following screen. 3. Select a ETH port as you will. You can select ENET1, ENET2, ENET3 or ENET4 port as the WAN interface and MSC mode as connection mode. 4. Click Apply/Save and you’ll see the following screen. 5. From Advanced Setup, click WAN Service to configure a WAN service over the interface you selected. 6. Click Add and you’ll see the following screen.
ADSL Router User Manual 7. Click Next and you’ll see the following screen. Select PPPoE as WAN service type for example. Click Next. 8. Enter the user name and password that your ISP has provided to you. Click Next.
ADSL Router User Manual PPPoE service name can be blank unless your Internet Service Provider gives you a value to enter. Authentication method is default to Auto. It is recommended that you leave the Authentication method in Auto, however, you may select PAP or CHAP if necessary. The default value for MTU (Maximum Transmission Unit) is 1500 for PPPoA and 1492 for PPPoE. Do not change these values unless your ISP asks you to.
ADSL Router User Manual The gateway can be configured to disconnect if there is no activity for a specific period of time by selecting the Dial on demand check box and entering the Inactivity timeout. The entered value must be between 1 minute and 4320 minutes. The PPP IP Extension is a special feature deployed by some service providers. Unless your service provider specifically requires this setup, do not select it.
ADSL Router User Manual 10. Get DNS server information from the selected WAN interface or enter static DNS server IP addresses. Click Next. 11. Make sure that the settings below match the settings provided by your ISP. Click on the Apply/Save button to save your configurations and reboot the ADSL router.
ADSL Router User Manual 5.2.3 LAN Settings From LAN, Configure the DSL Router’s IP Address and Subnet Mask for LAN interface. In this page, you can use DHCP (Dynamic Host Configuration Protocol) to control the assignment of IP addresses on your local network (LAN only). Item IP address Subnet mask Description This is the IP address that other devices on your local network will use to connect to the modem. This defines the size of your network. The default is 255.255.255.0.
ADSL Router User Manual IGMP Snooping is a method that actually “snoops” or inspects Enable IGMP snooping IGMP traffic on a switch. When enabled, the switch will watch for IGMP messages passed between a host and a router, and will add the necessary ports to its multicast table, ensuring that only the ports that require a given multicast stream actually receive it. The DHCP server assigns an IP addresses from a pre-set pool of Disable / Enable addresses upon request from DHCP client (e.g.
ADSL Router User Manual 5.3 Wireless setting 5.3.1 Basic Option Description Enable A check box that enables or disables the wireless LAN interfaces. The default is wireless to enable wireless communications. Hide Access Point Clients isolation Select Hide Access Point to protect the ADSL route access point from detection by wireless active scans. If you do not want the access point to be automatically detected by a wireless station, this checkbox should be deselected.
ADSL Router User Manual Country Drop-down menu that allows selection of specific channel. 5.3.2 Advanced Settings This page is where user specifies a number of advanced settings for wireless communications. Note: After making any changes, click Apply to save. Warning: The settings shown above are default settings. Changes made to these items can cause wireless communication problems.
ADSL Router User Manual user’s wireless devices. Channel Drop-down menu that allows selection of specific channel. This drop-down list lets user specify the wireless communication rate, which 54gTM Rate can be Auto (uses the highest rate when possible, or else a lower rate) or a fixed rate between 1 and 54 Mbps. This drop-down list lets user specify the wireless communication rate for Multicast rate multicast packets, which are sent to more than one destination at a time.
ADSL Router User Manual clients passively scan all radio channels, listening for beacons coming from access points. Before a client enters power-save mode, it needs the beacon interval to determine when to wake up for the next beacon (and learn whether the access point has any messages for it). User can enter any value between 1 and 65535, but the recommended range is 1 - 1000. XPress™ Technology is a feature in which two of our devices can communicate with each other at twice the normal rate.
ADSL Router User Manual 2. Configure WPA Pre-shared key as below and click Apply/Save. 3.Enable WPS as below. 4.Set WPS AP mode as Unconfigured and click Config AP.
ADSL Router User Manual 5. Set WPS AP mode as configured and click Save/Apply. 6.Now you can use a wireless adaptor with WPS function and the WPS button to connect to access the Internet. 7. To configure security features for the Wireless interface, please open Security item from Wireless menu. This web page offers nine authentication protocols for user to secure user’s data while connecting to networks. There are four selections including Open, Shared, 802.
ADSL Router User Manual There are several security methods to choose from, depending on user’s needs and the capabilities of user’s wireless machines. WEP open and WEP shared —WEP is an encryption scheme that is used to protect user’s wireless data communications. WEP uses a combination of 64-bit keys or 128-bit keys to provide access control to user’s network and encryption security for every data transmission.
ADSL Router User Manual client abilities, as well as a pre-shared key. After making changes, click Apply to save. 5.4 Management 5.4.1 Remote Access When the firewall is enabled on a WAN or LAN interface, all incoming IP traffic is BLOCKED. However, some IP traffic can be ACCEPTED by setting up filters. 1. Select Advanced Setup=>Security=>IP Filtering=>Incoming and Choose Add or Remove to configure incoming IP filters. 2.Click Add to add rules.
ADSL Router User Manual 5.4.2 TR-069 Client WAN Management Protocol (TR-069) allows a Auto-Configuration Server (ACS) to perform auto-configuration, provision, collection, and diagnostics to this device. Inform: Whether or not the CPE must periodically send CPE information to Server using the Inform method call. Inform Interval: The duration in seconds of the interval for which the CPE MUST attempt to connect with the ACS and call the Inform method if Inform is enabled.
ADSL Router User Manual making a connection to the ACS using the CPE WAN Management Protocol. This password is used only for authentication of the CPE. GetRPCMethods: Used by a CPE or ACS to discover the set of methods supported by the ACS or CPE it is in communicate with. 5.4.3 Printer Server Installations 1. Click “Advanced setupPrint Server” and then Check “Enable on-board printer server” and key in “Printer name”, “Make and model” 2.
ADSL Router User Manual 4. Select Connect to a printer on the Internet, type “http://192.168.1.1:631/printers/printer” and click “Next”. The printer name “Printer” must be the same name entered in the ADSL router “print server setting” as in step 1. 5. Select driver file directory on CD-ROM or in your hard disk and click “OK”. 6. Choose “Yes” or “No” for default printer setting and click “Next”.
ADSL Router 7. User Manual Click “Finish”.
ADSL Router Appendix: User Manual Frequent Asked Questions Q: None of the LEDs are on when you power on the ADSL router? A: Please make sure what you use is the power adaptor attached with the ADSL router package and checks the connection between the AC power and ADSL router.
ADSL Router User Manual Q: PC cannot browse Internet web page? A: Please make sure DNS server appointed to the PC is correct. You can use ping application program to test whether the PC can connect to the DNS server of the ADSL operator. Q: Initialization of the PVC connection failed? A: Be sure that cable is connected properly from the DSL port to the wall jack. The DSL LED on the front panel of the ADSL router should be on.
RF exposure information: To maintain compliance with FCC RF exposure requirements, use handset that maintain a 20cm separation distance between the user's body and the host. MPE limit for RF exposure at prediction frequency is 0.161mW/cm2. It satisfy RF exposure compliance. This device complies with part 15 of the FCC rules.
