KW55293 Wireless Router User Manual
KW55293 Wireless Router User Manual NOTICE This document contains proprietary information protected by copyright, and this Manual and all the accompanying hardware, software, and documentation are copyrighted. All rights are reserved. No part of this document may be photocopied or reproduced by mechanical, electronic, or other means in any form.
KW55293 Wireless Router User Manual FCC Warning: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
KW55293 Wireless Router User Manual FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
KW55293 Wireless Router User Manual Content 1 INTRODUCTION ....................................................................................................................... 2 1.1 M AIN FEATURES .............................................................................................................. 2 1.1.1 Wireless .......................................................................................................................... 2 1.1.2 Network Protocol and Features ....................
KW55293 Wireless Router 1 User Manual Introduction Thank you for choosing our product. The KA55293 Wireless Router uses CPE solution that fully complies with IEEE802.11b/g/n standards. It will provide your SOHO with convenient Internet. 1.1 Main Features 1.1.1 Wireless Fully IEEE 802.11b & IEEE 802.11g&IEEE 802.11n compatible. Wireless data rate up to 300 Mbps Operating in the unlicensed 2.4 GHz ISM band Supports 64/128 bits WEP, WPA, WPA2, WPA/WPA2-PSK, 802.1x 1.1.
KW55293 Wireless Router 1.1.4 1.1.5 1.1.6 1.
KW55293 Wireless Router 1.4 User Manual Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari Factory Defaults The device is configured with the following factory defaults: IP Address: 192.168.1.1 Subnet Mask: 255.255.255.0 1.5 Warnings and Cautions never use the product near water. To prevent dangerous overloading of the power circuit, be careful about the designed maximum power load ratings.
KW55293 Wireless Router 2 User Manual Hardware Description Front Panel LED Color Function Green On: Power on Off: No power Green On: LAN link established and active via LAN port Blinking: ADSL data activity occurs Off: No LAN link via LAN port Green On: The wireless module is ready and idle Blinking: Data transmitting or receiving over WLAN Off: The wireless function is off On: The WAN port has detected a link with an attached device Green Blinking: Data is being transmitted or received by the
KW55293 Wireless Router User Manual Rear panel Port Function WAN Connect the device to a cable or DSL modem ETH1,2,3,4 Connect the device to your PC's Ethernet port, or to the uplink port on your hub/switch, using a RJ-45 cable RESET System reset or reset to factory defaults WPS A convenient way for WPS set.
KW55293 Wireless Router User Manual 3 Hardware Installation This chapter shows you how to connect Router. Meanwhile, it introduces the appropriate environment for the Router and installation instructions. 1. Using an Ethernet Cable to connect the WAN port of the ROUTER to a cable or DSL modem. 2. Using an Ethernet Cable to connect the LAN port of the ROUTER to your LAN or a PC with network card installed. 3.
KW55293 Wireless Router 4 User Manual Local PC Configuration in Windows 95, 98, ME, XP,7 1. In the Windows task bar, click the “Start” button, point to “Settings”, and then click “Control Panel”. 2. Double-click the “Network” icon. 3. On the “Configuration” tab, select the TCP/IP network associated with your network card and then click “Properties”. 4. In the “TCP/IP Properties” dialog box, click the “IP Address” tab. Set the IP address as 192.168.1.x (x can be a decimal number from 2 to 254.
KW55293 Wireless Router 5 User Manual Configuring the Router 5.1 Web-based Management Guide In order to use the web-based management software, it will be necessary to use a computer that occupies the same subnet as the Router. The simplest way to do this for many users will be to use DHCP server that is enabled by default on the Router. 5.1.1 Login Launch a web browser, such as Internet Explorer, and then use http://192.168.1.1 to log on to the setting pages.
KW55293 Wireless Router User Manual 3.2 Quick Installation Guide After successfully log in, you can click “Setup” configure your router, we can select “Manual” or “Next” button setup KW55293,Next will guide us for a basic setting step by step,and the Manual will guide us to home page for more detailed setup.here we Choose next enter quick setup mode to quickly configure your Router. Then WAN Connection Type page will appear, shown as bellow.
KW55293 Wireless Router User Manual Enter the SSID what you want to use, and configure the security settings of your wireless network. then click Next. Click Finish to save you settings.
KW55293 Wireless Router User Manual 5.1.2 Network (WANSettings) KW55293 supports three types WAN connection.they are DHCP,Static IP,PPPOE, Select any of them you will be able to configure the corresponding connection of WAN. Choose menu “Setup →Internet Setup”, you can configure the IP WAN parameters 5.1.3 DHCP If your ISP provides the DHCP service, please choose Dynamic IP type, and the Router will automatically get IP parameters from your ISP. You can see the page as follows .
KW55293 Wireless Router User Manual 5.1.4 Static IP If your ISP provides a static or fixed IP Address, Subnet Mask, Gateway and DNS setting, select Static IP. The Static IP settings page will appear. IP Address: Enter the IP address in dotted-decimal notation provided by your ISP. Subnet Mask: Enter the subnet Mask in dotted-decimal notation provided by your ISP, usually is 255.255.255.0. Default Gateway:(Optional) Enter the gateway IP dotted-decimal notation provided by your ISP.
KW55293 Wireless Router User Manual 5.1.5 PPPOE If your ISP provides a PPPoE connection, select PPPoE option. And you should enter the following parameters. User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive.
KW55293 Wireless Router User Manual Domain Server - If your ISP gives you one or two DNS addresses,enter the addresses into the correct fields. Otherwise, the DNS servers will be assigned dynamically from your ISP. MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default MTU Size unless required by your ISP. Click the Apply Changes button to save your settings. 5.1.
KW55293 Wireless Router User Manual 5.2 Wireless Settings There are five submenus under the Wireless menu (shown as bellow): Wireless Basic MBSSID ,WPS, Wireless Advanced, Wireless Repeater. Click any of them, and you will be able to configure the corresponding function. 5.2.1 Basic Wireless Settings Choose menu “Wireless→Wireless Basics”, you can configure the basic settings for the wireless network on this page. Name（SSID）： Also called the SSID. Enter a value of up to 32 characters.
KW55293 Wireless Router User Manual Security Option: You can configure the security settings of your wireless network. There are six wireless security modes supported by the Router: WEP,802.1X,WPA, WPA2-PSK, WPA2, WPA2-PSK. Different item leads different web page settings. Please read the following information carefully: Done :If you do not want to use wireless security, check this radio button. But it’s strongly recommended to choose one of the following modes to enable security.
KW55293 Wireless Router User Manual 5.2.3 MBSSID Choose menu “Wireless→MBSSID”, you can configure the Guest Network Wireless Settings on the page as shown: Enable Guest Network :You can on or off MBSSID function Total Guest Allowed:You can configure the number of guest Enable SSID Broadcast:Enable or Disable the SSID Broadcast Allow Gust to access My Local Netword:If enabled, guests can communicate with hosts.
KW55293 Wireless Router User Manual 5.2.4 Wireless Advanced Choose menu “Wireless → Wireless Advanced”, you can configure the wireless advanced Settings on the page as shown: Enabled Wireless: Enabled or Disabled wireless function Fragmentation Threshold - This value is the maximum size determining whether packets will be fragmented. Setting the Fragmentation Threshold too low may result in poor network performance because of excessive packets. 2346 is the default setting and is recommended.
KW55293 Wireless Router User Manual 5.3 DHCP Settings Choose menu “Setup→Local Network→DHCP Server Settings”, you can configure the DHCP Server on the page as shown bellow.The Router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PC(s) that are connected to the Router on the LAN. DHCP Server:Enable or Disable the DHCP server.
KW55293 Wireless Router User Manual 5.4 Factory Default Choose menu “Maintenance→ Reboot”, and you can restore the configurations of the Router to factory defaults on the following screen Click the Reboot button to reset all configuration settings to their default values. The default User Name: Admin The default Subnet Mask: 255.255.255.0 Note: All changed settings will be lost when defaults are restored.
KW55293 Wireless Router User Manual Appendix: Frequent Asked Questions Q: None of the LEDs are on when user power on the ADSL router? A: Please make sure what user use is the power adaptor attached with the ADSL router package，and check the connection between the AC power and ADSL router.
KW55293 Wireless Router A: User Manual Please make sure DNS server appointed to the PC is correct. User can use ping application program to test whether the PC can connect to the DNS server of the ADSL operator. Q: Initialization of the PVC connection failed? A: Be sure that cable is connected properly from the DSL port to the wall jack. The DSL LED on the front panel of the ADSL router should be on.
