KW5212H WLAN VDSL Router User Manual
WLAN VDSL Router User Manual NOTICE This document contains proprietary information protected by copyright, and this Manual and all the accompanying hardware, software, and documentation are copyrighted. All rights are reserved. No part of this document may be photocopied or reproduced by mechanical, electronic, or other means in any form.
WLAN VDSL Router User Manual Content 1 OVERVIEW ................................................................................................................................1 1.1 FEATURES .............................................................................................................................1 1.2 PACKET CONTENTS.............................................................................................................3 1.3 SYSTEM REQUIREMENTS .................................
WLAN VDSL Router User Manual 1 Overview Thank you for choosing our product. The product is a Wireless VDSL router combining an VDSL modem, an 802.11n wireless router ,a 4-port switch and an USB port in one unit, bringing high-speed wireless Internet connection to a home or office. 1.1 Features 1.1.1 Data Rate Downstream data rate up to 100 Mbps Upstream data rate up to 50Mbps 1.1.2 VDSL Compliant ITU G.992.1 (G.DMT) ITU G.993.2 (G.vdsl2) (Profile 8a, 8b, 8c, 8d, 12a,12b and 17a) ITU G.992.
WLAN VDSL Router User Manual IP Static Routing Routing Information Protocol (RIP, RIPv2) Network Address Translation (NAT) Virtual Server, Port Forwarding Dynamic Host Configuration Protocol (DHCP) DNS Relay, DDNS IGMP Proxy Simple Network Time Protocol (SNTP) VPN pass-through (IPSec/PPTP/L2TP) Parent control 1.1.5 ATM Capabilities RFC 1483 Multi-protocol over ATM “Bridged Ethernet” compliant RFC 2364 PPP over ATM compliant RFC 2516 PPP over Ethernet compliant ATM Forum UNI3.
WLAN VDSL Router User Manual 1.1.7 1.1.8 1.1.9 1.
WLAN VDSL Router User Manual Subscription for ADSL service. Your ADSL service provider should provide you with at least one valid IP address (static assignment or dynamic assignment via dial-up connection). One or more computers, each contains an Ethernet 10/100M Base-T network interface card (NIC). A hub or switch, if you are connecting the device to more than one computer. For system configuration using the supplied web-based program: A web browser such as Internet Explorer v5.
WLAN VDSL Router User Manual 2 Hardware Description Front Panel LED Color PWR Green Function On: Power on Off: No power On: LAN link established and active via LAN port LAN1,2,3,4 Green Blinking: DSL data activity occurs Off: No LAN link via LAN port On: The wireless module is ready and idle WLAN Blinking: Data transmitting or receiving over Green WLAN Off: The wireless function is off DSL INET Green On: DSL link established and active Quick Blinking: DSL is trying to establish a connect
WLAN VDSL Router User Manual Rear panel Port DSL ETH1,2,3,4 USB Function Connect the device to an DSL telephone jack or splitter using a RJ-11 telephone cable Connect the device to your PC's Ethernet port, or to the uplink port on your hub/switch, using a RJ-45 cable Connect the device to a printer ON/OFF Switch it on or off POWER Connect to the supplied power adapter Side panel WIFI button: Enable or disable wireless function. Reset button: System reset or reset to factory defaults.
WLAN VDSL Router User Manual 3 Hardware Installation This chapter shows you how to connect Router. Meanwhile, it introduces the appropriate environment for the Router and installation instructions. 1. Using a telephone line to connect the DSL port of ROUTER to the MODEM port of the splitter, and using a other telephone line connect your telephone to the PHONE port of the splitter, then connect the wall phone jack to the LINE port of the splitter.
WLAN VDSL Router 4 4.1 User Manual PC Configuration Guide Local PC Configuration in Windows 95, 98, ME, XP,7 1. In the Windows task bar, click the “Start” button, point to “Settings”, and then click “Control Panel”. 2. Double-click the “Network” icon. 3. On the “Configuration” tab, select the TCP/IP network associated with your network card and then click “Properties”. 4. In the “TCP/IP Properties” dialog box, click the “IP Address” tab. Set the IP address as 192.168.1.
WLAN VDSL Router 5 User Manual Web-based Management Guide In order to use the web-based management software it will be necessary to use a computer that occupies the same subnet as the Router. The simplest way to do this for many users will be to use DHCP server that is enabled by default on the Router. 5.1 LAN setting page Launch a web browser, such as Internet Explorer, and then use http://192.168.1.1 to log on to the setting pages.
WLAN VDSL Router User Manual We can select wizard setup or advanced setup mode to setup KW5212.the wizard set up will guide us for a basic setting,and the advanced setup will guide us to home page for more detailed setup. 5.2 Internet Access Configuration 5.2.1 ADSL Setup From home page, you can find Advanced Setup option on the left router configuration page. 1. From Layer2 Interface, click ATM Interface. you can set it up according to the following steps.
WLAN VDSL Router User Manual 3. Click WAN Service from the left menu. 4. Click Add to select a layer 2 interface for this service and then click Next. 5. Choose WAN service type, just choose PPPoE for example here. You can enter your own service description here if you want and then click Next. 6. Input PPP Username & PPP Password and then click Next. The user interface allows a maximum of 256 characters in the user name and a maximum of 32 characters in the password.
WLAN VDSL Router User Manual PPPoE service name can be blank unless your Internet Service Provider gives you a value to enter. Authentication method is default to Auto. It is recommended that you leave the Authentication method in Auto, however, you may select PAP or CHAP if necessary. The default value for MTU (Maximum Transmission Unit) is 1500 for PPPoA and 1492 for PPPoE. Do not change these values unless your ISP asks you to.
WLAN VDSL Router User Manual Enable Full Cone NAT: In full cone NAT, all requests from the same private IP address and port are mapped to the same public source IP address and port. Someone on the Internet only needs to know the mapping scheme in order to send packets to a device behind the VDSL Device. The gateway can be configured to disconnect if there is no activity for a specific period of time by selecting the Dial on demand check box and entering the Inactivity timeout.
WLAN VDSL Router User Manual The gateway extends the IP subnet at the remote service provider to the LAN computer. That is, the PC becomes a host belonging to the same IP subnet. The ADSL gateway bridges the IP packets between WAN and LAN ports, unless the packet is addressed to the gateway's LAN IP address. 7. Select a preferred wan interface as the system default gateway. 8. Get DNS server information from the selected WAN interface or enter static DNS server IP addresses.
WLAN VDSL Router User Manual 9. Make sure that the settings below match the settings provided by your ISP. Click on the Apply/Save button to save your configurations. 5.2.2 VDSL Setup From home page, you can find Advanced Setup option on the left router configuration page. 1. From Layer2 Interface, click PTM Interface. you can set it up according to the following steps. You Choose Add, or Remove to configure DSL PTM interfaces. 2.
WLAN VDSL Router User Manual 3. Click WAN Service from the left menu. 4.Click Add to select a layer 2 interface for this service and then click Next. 5. Choose WAN service type, just choose PPPoE for example here. You can enter your own service description here if you want and then click Next. 6. Input PPP Username & PPP Password and then click Next. The user interface allows a maximum of 256 characters in the user name and a maximum of 32 characters in the password.
WLAN VDSL Router User Manual PPPoE service name can be blank unless your Internet Service Provider gives you a value to enter. Authentication method is default to Auto. It is recommended that you leave the Authentication method in Auto, however, you may select PAP or CHAP if necessary. The default value for MTU (Maximum Transmission Unit) is 1500 for PPPoA and 1492 for PPPoE. Do not change these values unless your ISP asks you to.
WLAN VDSL Router User Manual Someone on the Internet only needs to know the mapping scheme in order to send packets to a device behind the VDSL Device. The gateway can be configured to disconnect if there is no activity for a specific period of time by selecting the Dial on demand check box and entering the Inactivity timeout. The entered value must be between 1 minute and 4320 minutes.
WLAN VDSL Router User Manual The gateway extends the IP subnet at the remote service provider to the LAN computer. That is, the PC becomes a host belonging to the same IP subnet. The ADSL gateway bridges the IP packets between WAN and LAN ports, unless the packet is addressed to the gateway's LAN IP address. 7. Select a preferred wan interface as the system default gateway. 8. Get DNS server information from the selected WAN interface or enter static DNS server IP addresses.
WLAN VDSL Router 9. User Manual Make sure that the settings below match the settings provided by your ISP. Click on the Apply/Save button to save your configurations. 5.2.3 Router Mode Setup 1. From Advanced Setup, click Layer2 Interface and select ETH Interface. Before you configure ETH WAN interface, you’d better remove all PVC settings from ATM interface. 2. Click Add and you’ll see the following screen. 3. Select a ETH port as you will.
WLAN VDSL Router 5. User Manual From Advanced Setup, click WAN Service to configure a WAN service over the interface you selected. 6. Click Add and you’ll see the following screen. 7. Click Next and you’ll see the following screen. Select PPPoE as WAN service type for example. Click Next.
WLAN VDSL Router User Manual 8. Enter the user name and password that your ISP has provided to you. Click Next.
WLAN VDSL Router User Manual PPPoE service name can be blank unless your Internet Service Provider gives you a value to enter. Authentication method is default to Auto. It is recommended that you leave the Authentication method in Auto, however, you may select PAP or CHAP if necessary.
WLAN VDSL Router User Manual PPPoA and 1492 for PPPoE. Do not change these values unless your ISP asks you to. Enable Full Cone NAT: In full cone NAT, all requests from the same private IP address and port are mapped to the same public source IP address and port. Someone on the Internet only needs to know the mapping scheme in order to send packets to a device behind the VDSL Device.
WLAN VDSL Router User Manual server within the ADSL gateway has only a single IP address to assign to a LAN device. NAPT and firewall are disabled when this option is selected. The gateway becomes the default gateway and DNS server to the computer through DHCP using the LAN interface IP address. The gateway extends the IP subnet at the remote service provider to the LAN computer. That is, the PC becomes a host belonging to the same IP subnet.
WLAN VDSL Router User Manual 11. Make sure that the settings below match the settings provided by your ISP. Click on the Apply/Save button to save your configurations and reboot the ADSL router.
WLAN VDSL Router User Manual 5.2.4 LAN Settings From LAN, Configure the DSL Router’s IP Address and Subnet Mask for LAN interface. In this page, you can use DHCP (Dynamic Host Configuration Protocol) to control the assignment of IP addresses on your local network (LAN only).KW5212 support IPv4 /IPv6 dual stack. 5.2.4.1 IPv4 LAN Settings Item IP address Subnet mask Description This is the IP address that other devices on your local network will use to connect to the modem.
WLAN VDSL Router User Manual IGMP Snooping is a method that actually “snoops” or inspects Enable IGMP snooping IGMP traffic on a switch. When enabled, the switch will watch for IGMP messages passed between a host and a router, and will add the necessary ports to its multicast table, ensuring that only the ports that require a given multicast stream actually receive it. The DHCP server assigns an IP addresses from a pre-set pool of Disable / Enable addresses upon request from DHCP client (e.g.
WLAN VDSL Router User Manual 5.2.4.2 IPv6 LAN Settings Item IPv6 address Subnet mask Description This is the IP address that other devices on your local network will use to connect to the modem. This defines the size of your network. The default is 255.255.255.0. IGMP Snooping is a method that actually “snoops” or inspects IGMP traffic on a switch.
WLAN VDSL Router User Manual Use blocking mode to discard unknown multicast traffic. The DHCP server assigns an IP addresses from a pre-set pool of Disable / Enable addresses upon request from DHCP client (e.g. your computer). DHCP server Do not disable the DHCP server unless you wish to let another device handle IP address issuance on the local network. Start / end IP This is the beginning and ending range for the DHCP server address addresses.
WLAN VDSL Router User Manual 5.3 Wireless setting 5.3.1 Basic Option Description Enable A checkbox that enables or disables the wireless LAN interfaces. The default wireless is to enable wireless communications. Select Hide Access Point to protect the ADSL route access point from detection by wireless active scans. If you do not want the access point to be automatically detected by a wireless station, this checkbox should be deselected. Hide Access The station will not discover this access point.
WLAN VDSL Router isolation User Manual each other. Enter a name for user’s wireless network here. SSID stands for Service Set Identifier. This name must be between 1 and 32 characters long. The default Network name WLAN name (SSID) All wireless clients must either detect the gateway or be configured with the correct SSID to access the Internet. BSSID Displays the gateway's wireless MAC address. (User may need this address if user is using WDS or multiple gateways.) Click Apply to save changes.
WLAN VDSL Router User Manual 3.Enable WPS as below. 4.Set WPS AP mode as unconfigured and click Config AP. 5. Set WPS AP mode as configured and click Save/Apply.
WLAN VDSL Router User Manual 6. Now you can use a wireless adaptor with WPS function and the WPS button to connect KW5212 to access the Internet. 7. To configure security features for the Wireless interface, please open Security item from Wireless menu. This web page offers nine authentication protocols for user to secure user’s data while connecting to networks. There are four selections including Open, Shared, 802.1X,WPA, WPA-PSK, WPA2, WPA2-PSK, Mixed WPA-WPA2, Mixed WPA-WPA2-PSK.
WLAN VDSL Router User Manual of 64-bit keys or 128-bit keys to provide access control to user’s network and encryption security for every data transmission. To decode a data transmission, each wireless client on the network must use an identical 64-bit or 128-bit key. WEP is an older wireless encryption method that is not as hard to break as the more-recent WPA. 802.1x — In 802.1x (also known as RADIUS), a separate machine called an authentication server receives a user ID and password.
WLAN VDSL Router 5.4 User Manual Printer Server Installations 1. Click “Advanced setupPrint Server” and then Check “Enable on-board printer server” and key in “Printer name”, “Make and model” . 2. Click on Add a printer from Control Panel of the Windows computer and click “Next”. 3. Select “Network Printer” and click “Next”.
WLAN VDSL Router User Manual 4. Select Connect to a printer on the Internet, type “http://192.168.1.1:631/printers/printer” and click “Next”. The printer name “Printer” must be the same name entered in the ADSL router “print server setting” as in step 1. 5. Select driver file directory on CD-ROM or in your hard disk and click “OK”. 6. Choose “Yes” or “No” for default printer setting and click “Next”.
WLAN VDSL Router 7. User Manual Click “Finish”.
WLAN VDSL Router Appendix: User Manual Frequent Asked Questions Q: None of the LEDs are on when you power on the ADSL router? A: Please make sure what you use is the power adaptor attached with the ADSL router package and checks the connection between the AC power and ADSL router.
WLAN VDSL Router User Manual Q: PC cannot browse Internet web page? A: Please make sure DNS server appointed to the PC is correct. You can use ping application program to test whether the PC can connect to the DNS server of the ADSL operator. Q: Initialization of the PVC connection failed? A: Be sure that cable is connected properly from the DSL port to the wall jack. The DSL LED on the front panel of the ADSL router should be on.
FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
1. This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. 2. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA.
be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. The REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point. For this product the FCC Registration number is [US: U5IDL01BKW5212] indicates the REN would be 01B.
