MCT247 2.
MCT247 TRANSCEIVER INDEX DESCRIPTION ........................................................................... 2 OPERATION .............................................................................. 3 INSTALLATION ......................................................................... 4 BEFORE APPLYING POWER! ...................................................... 6 TROUBLESHOOTING ................................................................. 6 TRANSCEIVER PICTORIAL ..............................
MCT247 TRANSCEIVER DESCRIPTION The MCT247 hopping control products by Kar-Tech, at is a spread Kar-Tech. There are no user frequency serviceable parts on the MCT247 spectrum transceiver. The MCT247 is not transceiver module designed to for sale by itself. be compatible with US (FCC CFR 47 Part Canadian 247 15 (15.247)), (RSS-210), Issue 5/ANSI C The MCT247 is not designed for EU(RSS- 2/RSS-GEN Issue C63.10:2013, IEC multiple and license free use in the 2.4 GHz to 2.470GHz.
MCT247 TRANSCEIVER OPERATION The The MCT247 is a radio MCT247 uses Frequency Hopping Spread Spectrum, that transceiver module for the 2.4 uses GHz ISM bands. The transceiver 2.407GHZ and 2.470GHZ with a microcontroller includes a CPU, 1MHz resolution.
MCT247 TRANSCEIVER INSTALLATION 1) Solder product still complies. Look the for: MCT247 a. Peak Power < 20dBm transceiver directly to the host’s compatible connector. of the host enclosure in a visible area. On the label, FCC following: ID: P4U- MCT247” and “Contains IC: 4534A-MCT247” 4) Connect the should < 40dBuV/m. 3) Place a label on the outside “Contains 1GHz above be < Below 1GHz, they should be as shown below: the peaks 74dBuv/m. 2) Print and attach the label include b.
MCT247 TRANSCEIVER Application Requirements: A) Power the MCT247 serviceable parts the modules. radio They should in not Transceiver with 3.3VDC remove or install radio nominal modules. peak voltage, current with draw of b. The 150mA. “Instructions To The User” section. B) Do not remove the shield c. The “Industry Canada on the MCT247. Statement”. C) If you use something other d.
MCT247 TRANSCEIVER BEFORE APPLYING POWER! Check power and ground for proper polarity. Read the rest of this manual. TROUBLESHOOTING There are no user serviceable parts in the MCT247 Transceiver. Contact your KARTECH representative for further instructions or servicing. PARTS LIST PART NUMBER 021535C DESCRIPTION MCT247 RADIO TRANSCEIVER – WIRE ANTENNA There are no user-serviceable parts inside the transmitter or the receiver. Return the units for service.
MCT247 TRANSCEIVER 1.8900 0.0900 0.1000 1 1.2500 1.
MCT247 TRANSCEIVER Pinout Pin 1 2 3 4 5 6 Function GND Not Used GND Not Used Not Used NC Pin 7 8 9 10 11 12 Function NC Not Used Not Used NC RXD TXD Pin 13 14 15 16 17 18 Function NC NC NC NC VIN 3.3V GND SPECIFICATIONS Equipment Class .............................. Part 15 Spread Spectrum Transmitter FCC ID .............................................................................. P4U-MCT247 ICC (Industry Canada Certification) ID ..............................
MCT247 TRANSCEIVER INSTRUCTION TO THE USER This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
MCT247 TRANSCEIVER INDUSTRY CANADA STATEMENTS This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
MCT247 TRANSCEIVER EUROPE CE NOTICE This device has been tested and certified for use in the European Union. See the Declaration of Conformity (DOC) for specifics. If this device is used in a product, the OEM has the responsibility to verify compliance of the final product to the EU standards. A declaration of Conformity must be issued and kept on file as described in the Radio and Telecommunications Terminal Equipment (R&TTE) Directive.
2.2 List of applicable FCC rules CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular transmitter 2.3 Specific operational use conditions This module is stand-alone modular.If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system. 2.
