User's Manual
MARKIVIndustriesCorp
®
S
S
h
h
e
e
e
e
t
t
1
1
o
o
f
f
1
1
8
8
0
0
2
2
0
0
0
0
1
1
-
-
0
0
0
0
1
1
.
.
d
d
o
o
c
c
N
N
o
o
v
v
1
1
4
4
,
,
2
2
0
0
0
0
8
8
©
©
M
M
A
A
R
R
K
K
I
I
V
V
I
I
N
N
D
D
U
U
S
S
T
T
R
R
I
I
E
E
S
S
C
C
o
o
r
r
p
p
E
E
X
X
C
C
E
E
P
P
T
T
A
A
S
S
M
M
A
A
Y
Y
B
B
E
E
O
O
T
T
H
H
E
E
R
R
W
W
I
I
S
S
E
E
P
P
R
R
O
O
V
V
I
I
D
D
E
E
D
D
B
B
Y
Y
C
C
O
O
N
N
T
T
R
R
A
A
C
C
T
T
,
,
T
T
H
H
E
E
S
S
E
E
D
D
R
R
A
A
W
W
I
I
N
N
G
G
S
S
A
A
N
N
D
D
S
S
P
P
E
E
C
C
I
I
F
F
I
I
C
C
A
A
T
T
I
I
O
O
N
N
S
S
C
C
O
O
N
N
T
T
A
A
I
I
N
N
P
P
R
R
O
O
P
P
R
R
I
I
E
E
T
T
A
A
R
R
Y
Y
I
I
N
N
F
F
O
O
R
R
M
M
A
A
T
T
I
I
O
O
N
N
A
A
N
N
D
D
A
A
R
R
E
E
T
T
H
H
E
E
P
P
R
R
O
O
P
P
E
E
R
R
T
T
Y
Y
O
O
F
F
M
M
A
A
R
R
K
K
I
I
V
V
I
I
N
N
D
D
U
U
S
S
T
T
R
R
I
I
E
E
S
S
C
C
O
O
R
R
P
P
A
A
N
N
D
D
A
A
R
R
E
E
I
I
S
S
S
S
U
U
E
E
D
D
I
I
N
N
S
S
T
T
R
R
I
I
C
C
T
T
C
C
O
O
N
N
F
F
I
I
D
D
E
E
N
N
C
C
E
E
A
A
N
N
D
D
S
S
H
H
A
A
L
L
L
L
N
N
O
O
T
T
B
B
E
E
T
T
R
R
A
A
N
N
S
S
M
M
I
I
T
T
T
T
E
E
D
D
O
O
R
R
R
R
E
E
P
P
R
R
O
O
D
D
U
U
C
C
E
E
D
D
O
O
R
R
C
C
O
O
P
P
I
I
E
E
D
D
O
O
R
R
U
U
S
S
E
E
D
D
A
A
S
S
T
T
H
H
E
E
B
B
A
A
S
S
I
I
S
S
F
F
O
O
R
R
M
M
A
A
N
N
U
U
F
F
A
A
C
C
T
T
U
U
R
R
E
E
O
O
R
R
S
S
A
A
L
L
E
E
O
O
F
F
A
A
P
P
P
P
A
A
R
R
A
A
T
T
U
U
S
S
W
W
I
I
T
T
H
H
O
O
U
U
T
T
P
P
R
R
I
I
O
O
R
R
W
W
R
R
I
I
T
T
T
T
E
E
N
N
P
P
E
E
R
R
M
M
I
I
S
S
S
S
I
I
O
O
N
N
.
.
Short Range Vehicle-to-Roadside Communications Equipment for Automatic Vehicle Identification
G4P Transponder Mounting Instructions
for car interior on windshield
For proper operation, make sure the transponder is mounted as follows:
1. Identify the front face of the transponder. It displays your agency label and
two upward-pointing arrows. (Fig.-1) This side faces the driver with the ar-
rows pointing toward the roof of your vehicle.
2. Identify the position in your vehicle in which the transponder will be mounted.
The preferred location is between the exposed edge of the windshield (roof-
line) and the rear view mirror post—as long as the clearances in Fig.-2 can
be maintained. If there is insufficient room, the alternate location shown in
Fig.-3 must be used.
3. Having determined the mounting position in your vehicle, clean the inside
surface of that section of the windshield if necessary. Now carefully remove
the protective backing from the Dual Lock
TM
mounting strips on the rear of the transponder as shown in Fig. 4 and
firmly press the rear of the transponder against the glass. Maintain the pressure for about 15 seconds to achieve a
good bond
The transponder may be removed by lifting any one corner with sufficient pressure to separate the Dual Lock
TM
strips.
Do not remove the Dual Lock
TM
from the windshield and reuse it; obtain new strips from your service center if necessary.
This equipment must be installed to
provide a separation distance of at least 20 cm from all nearby persons and must
not be co-located or operating in conjunction with any other antenna or transmitter.
Fig.-2 Preferred Mounting Location
Fig.-1 Transponder Front Face
Fig.-4 Transponder Rear Face
Fig.-3 Alternate Mounting Location
ARROWS POINT UP
Rear view mirror Transponder