Table of Contents FCC NOTE Chapter 1: Getting Started Unpacking Operating Environment Quick Start-up Powering the System AC Power Adapter Battery Inserting .. Removing. Recharging by AC Poe ce Proper Handling of the Battery Pack Opening the LCD Cover LED Indicators on the LCD Cove Top-Front View coin LCD Panel Stereo Speakers Track pad and Buttons. Keyboard... Microphone.
PC Card Sockets Right-side Stands. Left-side View . DC-in Socket Ventilation Left-side Stands Bottom View... 2.3” Hard Disk Riv CPU Cover... ins Battery Pack. CD-ROM Cover... Chapter 2: Operation Upgrading CPU... . Replacing CPU. Setting DIP Switch Accessing the 10-Pole DIP Switz CPU Core Frequency Setting: Flash ROM BIOS Settings. Accessing the 8-Pole DIP Switch. CPU Core Voltage Settings Accessing the 2-Pole DIP Switch...
Chapter 1: Getting Started 1-3 Operating Environment As with any other precision electronic equipment, proper care and operation of our Notebook will provide long and reliable service. Be sure the computer system is not: Exposed to excessive heat or direct sunlight. Subjected to shock or vibration. Exposed to strong magnetic fields. Left in a place where foreign matter or moisture may enter the system.
1-4 User's Manual Quick Start-up Powering the System AC Power Adapter Use only the power adapter that comes with your Notebook Computer. System operation with an incorrect power adapter will cause damage to the Notebook and its components 1. Plug the power adapter to the DC-in socket on the left panel of the Notebook. Connect the power cord to the power adapter.
Chapter 1: Getting Started 1-5 Battery Pack Power for continuous portable operation of the Notebook is provided by a battery pack. When using the battery no external power source 1s required. However, the actual operating time will be determined by the application used and the configuration set. Inserting I. Tum the Notebook over. 2. Position the battery pack and firmly fit it into the Notebook (Figure 14). 3. The two latches will click into place when it is seated Removing 1. Tum the Notebook over. 2.
1-8 User's Manual Recharging by AC Power The system's battery pack will recharge whenever the system is plugged into the AC power supply, regardless of whether the system is being operated or not. Please refer to Chapter 1, System Status LED Indicators for more information concerning battery charge status. Off-Line Charge The Notebook system is powered off. Connect the AC adapter to the unit. Its DC output will be used solely to charge the battery.
Chapter 1: Getting Started 1-7 Opening the LCD Cover 1. To release the top cover slide the latch to the right (Figure 1-6). 2. Lift the top cover to reveal the LCD panel and keyboard (Figure 1-7). 3. Adjust the LCD panel to a comfortable viewing angle. 4. Press the power button to turn the system on or off (refer to Chapter 1. Top-Toronto View for the information of the power button).
1-8 User's Manual LED Indicators on the LCD Cover Eon Color Description Green @ Battery power is used with system turned on. Red | AC power is used with system turned on. Green Battery is fully charged. a8 | Red Battery is being charged. © Blinking Red | Battery power is critically low.
Chapter 1: Getting Started 1-8 Top-Front View LCD Panel The Notebook provides you with a large LCD panel. Depending upon the model you have purchased, it can either be a 13.3” XGA (1024x768 pixels) compatible, using TFT technology, or a 12.17 SAGA (800x600 pixels) compatible, using DST or TFT technology. The LCD panel is driven by a PCI local bus video controller with 2MB video memory Stereo Speakers Two built-in speakers provide clear stereo sound.
1-10 User's Manual System Status LED Indicators The LED indicators display the system’s operation status Icon Color Description ® Green Battery power is used with system turned on. i Red AC power is used with system turned on. Green | Battery is fully charged. QE ] Red Battery is being charged. Blinking Red ] Battery power is critically low i 3 Green | The hard disk is being accessed. | . Luis no The system has entered the Power On Suspend Yo Green | pO) mode.
1-12 User's Manual Rear View & Microphone-in Jack Use this jack to connect a microphone to the system for audio input __ Headphone Jack » + Headphone can be attached to the system through this jack for audio output, so can external speakers that have built-in output power amplifier Security Connector The Security Connector is used to protect your Notebook from being stolen. Wrap the steel cable around your desk.
Chapter 1: Getting Started 1-13 Microphone-in jack Headphone jack | Serial port Parallel port CRT port P82 type port Security connector Figure 1-11
1-14 User's Manual Right-side View 3.5" Floppy Diskette Drive The Notebook comes standard with a 1 440B floppy drive installed. Press the button on its top-right side to eject the diskette 5.25" CD-ROM Drive The $257 IDE CD-ROM module is designed to be changeable installing or removing the two Screws that fasten the CD-ROM drive. The eject Burton is located in the middle of the front cover of the CD-ROM drive. Pressing it will release the CD tray.
Chapter 1: Getting Started 1-15 3.
1-16 User's Manual Left-side View DC-in Socket Plug the AC adapter into this socket for power supply. To disconnect, pull the plug (not the cord) directly back Ventilation The Notebook provides ventilation to dissipate the system's operating heat. Do not block or obstruct it during operation. Left-side Stands When a high speed CPU is installed, the erecting stands on both sides will help heat dissipation during operation.
Chapter 1: Getting Started 1-17 Bottom View 2.5” Hard Disk Drive The 2.5” hard disk drive accepts any 2.5” IDE hard disk drive with a height of 12.7mm or less. Accessing the corresponding screws will allow you to install or to remove this hard disk drive. Refer to Chapter 2: Operation, for more information. CPU Cover Detaching the screws to remove the cover will reveal the microprocessor. You may upgrade the CPU for higher system performance.
Chapter 2: Operation 21 Chapter 2: Operation The Notebook has many advanced features to help you with your computing work. This chapter describes each of the Notebook’s hardware features and shows you how to use them. Before you begin working with any internal components of the Notebook, remove the battery and disconnect the AC power adapter. Make sure that you wear an anti-static wrist strap to ground yourself before working with any internal components of the Notebook.
2-2 User's Manual Upgrading CPU The system is capable of hosting a wide range of Intel CPU. Up our CPU will increase your computing speed. The higher the CPU installed, the better the system performance. Different C Pus may have different power voltages. 1f you want to upgrade the CPU, remember to adjust the corresponding settings. Replacing CPU |. Remove all power sources (AC power and battery). Turn the Notebook over. Remove the CPU cover.
Chapter 2: Operation 2-3 Setting DIP Switch You need to set the following DIP Switches for correct system configuration: e 10-pole DIP Switch for CPU core frequency (MHz) and flash ROM BIOS. + pole DIP Switch for CPU core voltage. * 2-pole DIP Switch for CPU I/O voltage. Accessing the 10-Pole DIP Switch Turn the system power off.
Chapter 2: Operation 2-5 CPU Core Frequency Settings The correct configuration for CPU core frequency is listed as follows: Pentium Processor at 3.3V I/O Voltage Frequency [31456 [wi XXX onlooker on] or onl Not Applied Pentium Processor at 2.5V 1/0 Voltage Frequency 51617 !8]9 10 sm [XTX X Of [off Not Applied Flash ROM BIOS Settings In order to keep up with the latest system BIOS, your Notebook may be upgraded. Consult your dealer for further information.
2-6 User's Manual Accessing the 8-Pole DIP Switch Access the %-pole DIP Switch to set the CPU core voltage I. Turn the system poser off, 2, Turn the Notebook over. 1 Remove the CPU cover. Use the 8-pole DIP Switch to set the configuration (Figure 2-4).
Chapter 2; Operation Accessing the 2-Pole DIP Switch Access the 2-pole DIP Switch to set the CPU I/O voltage. 1. Turn the system power off. 2. Turn the Notebook over. 2.7 3. Remove the CPU cover. Use the 2-pole DIP Switch to set the configuration (Figure 2-5).
Chapter 2: Operation 2-9 Accessing the Memory Sockets 1. Turn the system power off. 2. Press the two keyboard latches so that the keyboard can be elevated {from its normal position (Figure 2-2). 3. Carefully lift the keyboard assembly out so that the ma inboard is exposed. Locate the memory sockets (Figure 2-6).
2-10 User's Manual Installing Memory Module Follow the steps below to install the memory module: 1. Turn the system power off. 2. Press the two keyboard latches so that the keyboard can be elevated from its normal position (Figure 2-2) Carefully lift the keyboard assembly out so that the ma inboard i$ exposed. Locate the memory sockets (Figure 2-6). 4. Position the memory module ata slight angle and fit its connectors into the socket firmly. Push the module down and ensure it locks into place (Figure 2-7).
Chapter 2: Operation 2-11 Removing Memory Module Turn the system power off. Press the two keyboard latches so that the keyboard can be elevated from its normal position (Figure 2-2). Carefully lift the keyboard assembly out to expose the ma inboard. Locate the memory sockets (Figure 2-6). Gently pull the two latches on both ends of the module outward. The module will pop up (Figure 2-8). Remove the memory module. Reinstall the keyboard assembly.
2-12 User's Manual Using Hard Disk Drive The hard disk drive is mounted in a removable case and may therefore be taken out to accommodate other 2.57 IDE hard disk drives with a height of 127mm. The system supports drives with capacities greater than 528MB through the Logical Block Addressing (LBA) mode. Tt also supports Programmed VO (PIO) mode 4 and provides a high performance data transfer rate at speeds up to 33 Microsecond (A TA-33). Removing 1. Turn the system power off. 2. Turn the Notebook over. 3.
Chapter 2: Operation __ 2-13 Replacing Hard Disk Drive The hard disk drive is contained within a case. Two screws on cache side of the case need to be removed so that the hard disk drive can be taken out of the case to replace with another one (Figure 2-10). The location of the two screws may be varied depending on different hard disk models. Gently disconnect the cable from the hard disk drive when taking it out of the case. Be careful not to bend any pins or crimp the cable.
2-14 User's Manual Using Floppy Disk Drive The Notebook comes standard with a 1.44MB floppy disk drive. It is labeled drive A: and may be used as a boot device if properly set. Inserting/Removing Diskettes When using the floppy drive, always insert your floppy diskette label-side up (Figure 2-11). To remove your diskette, press the jet button on the top-right comer of the floppy drive.
Chapter 2: Operation 2-15 Write-Protecting Diskettes Diskettes can be write-protected to prevent files from being accidentally erased or destroyed. To write-protect a 3.5” floppy diskette, move the built-in write-protect tab to the write-protect position, {“up” so that you can see through the “hale” in the upper, right-hand corner of the diskette.
2-16 User's Manual Using CD-ROM The Notebook comes standard with a removable 5.25” CD-ROM module it is labeled drive I): and may be used as a boot device if properly set. Do not disassemble the CD-ROM module. Only certified technicians should perform repairs to the CD-ROM module. To insert a CD, press the Eject Button and place the CD on the Duse Tray label-side facing up. Push the CD tray in and you are ready to start.
Chapter 2: Operation 297 Removing CD-ROM Module Turn the system power off. Turn the Notebook over. Remove the CD-ROM cover (Step | in Figure 2-13). Remove the screw to release the CD-ROM module. (Step 2 in Figure 2.13), Slide the CD-ROM module slightly out to disconnect the cable (Step 3 and Step 4 in Figure 2-13).
2-18 User's Manual Loading Compact Discs Turn on the power, Press the CD-ROM eject button, the disc tray will pop out partially. Pull the disc tray out. Carefully load the CD on the disc tray with label-side facing up. Press it gently to ensure jt fits into place (Figure 2-14). 5. Push the tray into the computer 10 close it.
Chapter 2: Operation 2-19 Handling of Compact Sises Proper handling of your CDs will prevent them from being damaged and ensure the accessibility of data stored an them. + Hold the CD by the edges; do not touch the surface of the disc » Use clean, soft, dry cloth to remove dust or fingerprints. s Do not write on the surface using pen. «Do not attach any paper or other materials to the surface of the disk.
2-20 User's Manual Using PC Card Sockets The Notebook provides system expansion capabilities with two PC card sockets (previously referred to as PCMCIA). PC cards 10 be inserted can be LAN, fax/modem, communication devices, or expanded memory. Both sockets support 3.3V 32-bit PC cards, referred to as Card Bus. The Card Bus sockets are backward compatible with SY 16-bit PC cards There are three types of PC cards. Type 1 measures 33mm thick; Type 11 5 0mm; and Type II 10.5mm.
Captor 2: Operation 2.21 Removing PC Cards To remove a PC card, press the appropriate eject button and the card will be ejected from its slot (please refer to Figure 2-17).
2-22 User's Manual Using Hot Keys Located on the bosom-left edge of the keyboard fallout is a colored Fn key. It is a special feature found only on the Notebook that provides for key combinations with other keys for easy access 10 system features.
2-24 User's Manual . . Using Numeric Keypad The colored keys in the middle section of the keyboard will function as a Numeric Keypad (Figure 2-19). The numeric keypad overlay can be used for numeric data input. Follow these steps to access the Numeric Keypad: 1. Press the Hemlock key to lock the Menu Keypad 5 Press the Fn key along with the colored keys to operate the Numeric Keypad.
Chapter 2: Operation 2-26 Windows 95 Special Keys Application Key The Application key has the same function as the secondary mouse button.
2-26 User's Manual Getting Familiar with LCD Panel Notebook Computer features the LCD panel display with the following: Lae « Allocate bus controller + 2MB video RAM GRAM type) « (Capability to support 1024x768 (XGA) resolution TFT display.
Chapter 2: Operation 2-27 Using Power Management The Notebook system provides you with various modes to manage its power consumption while maintaining system performance. Please refer to Chapter 3: BIOS Utilities, System Configuration Utility, Power Menu for more information. Advanced Power Management (APM 1.2) The Notebook provides built-in Advanced Power Management (APM 1.2) support to reduce power consumption. APM function varies depending on the operating system you are using.
2-28 User's Manual Hard Disk Standby The system will tum off the Notebooks hard disk drive motor if it bas not been accessed after a specified period of time. The motor will be muted back on once the system attempts 10 read or write data to it. Global Standby In Global Standby made, the CPU clock will be stopped and most controllable peripheral devices will be powered off. If the idle timer expires before any system activity is detected, the system will change from Standby mode into Suspend mode.
Chapter 2: Operation 2-28 Suspend and Resume When at extremely low power the system will halt operations yet retain all its programming. This is called Suspend Mode. The Suspend Mode features two levels: Powered-On-Suspend (POS) mode, and Suspend-To Disk (STD) mode. Be sure not to initiate the Suspend Mode when any of the disk drives is accessed such as HDD, FDD and CD-ROM drive. The system operation can be returned to exactly where it was suspended when wake-up event occur. This is called Resume.
2-30 User's Manual Suspend To Disk (STD) Suspend to Disk is a O-v olt suspend mode for system power management. STI) mode saves the maximum power but takes the longest time to return to full operation. 1. Use your operating system’s DISK program to delete all partitions of the hard disk if any already exist on the target drive. 2. Boot the system from the A: drive and run the OYMAKFIL.
Chapter 2: Operation 2.31 Attaching Peripheral Devices The herein mentioned shows you how to attach peripheral devices to the ports or jacks on the rear panel of the Notebook Computer. Attaching a Security Lock To protect your Notebook from being stolen, the computer is equipped with a security connector.
2-32 User's Manual Attaching a PS/2 Keyboard or Mouse The Notebook can be operated with 2 PS/2 keyboard or mouse attached by means of the PS/2 transfer cable. Attach the external keyboard or mouse as shown below (Figure 2-21) .
Chapter 2: Operation 2-33 Attaching a Serial Mouse The serial port features a 9-pin connector. You can connect any serial device such as a mouse to this port. 1. Turn the system power off. Connect the cable to the serial port on the rear of the Notebook Computer (Step 1 in Figure 2-22). 3. Tighten the screws that fasten the cable to the serial port (Step 2 in Figure 2-22). 4. Turn on the Notebook Computer. In addition, you may need to install the manufacturer-supplied driver for the serial mouse.
2-34 User's Manual Attaching a Parallel Printer You may connect any standard Electronics parallel printer to your Notebook using the parallel port. Turn the system power off. Connect the cable to the parallel port on the rear of the Notebook Computer {Step 1 in Figure 2-23). Tighten the screws that fasten the cable to the parallel port (Step 2 in Figure 2-23). Insert the other end of the cable to the printer’s connector Fasten the cable’s connector. oo Turn on the printer and Notebook Computer.
Chapter 2: Operation 2-35 Attaching an External Monitor (CRT) The computer is capable of displaying information not only on the LCD, but also on SAGA compatible displays attached to the computer. Information can be displayed on both the LCD and the external monitor simultaneously. Enter the System Configuration Utility (SCU) to select the appropriate parameters or use the Fn + T6 keys (refer to Chapter 2, Using Hot Keys). Turn the system power off.