English User Manual FMX2 TV Mount FULL MOTION FLAT PANEL TV MOUNT +14°/-8° 75 x 75 to 800 x 450 130 lbs (59 kg) VESA 3.2– 20” ±80° (8.
Table of Contents Table of Contents / Introduction . . . . . . . . . . . . . Supplied Parts & Hardware . . . . . . . . . . . . . . . . . . Setup - Step 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setup - Step 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3 4 5 Setup - Steps 3 to 4 . . . . . . . . . . . . . . . . . . . . . . . Setup - Steps 5 to 6 . . . . . . . . . . . . . . . . . . . . . . . Other Kanto Products . . . . . . . . . . . . . . . . . . . . . . Warranty . . . . . . .
Supplied Parts and Hardware x4 x4 A: M5 x 12mm Bolt B: M5 x 30mm Bolt x4 C: M6 x 12mm Bolt x4 H: M5/M6 14mm Plastic Spacer G: M8 x 50mm Bolt x4 x4 D: M6 x 35mm Bolt x4 F: M8 x 35mm Bolt J: M5/M6/M8 5mm Plastic Spacer x4 x4 x8 I: M5/M6/M8 10mm Plastic Spacer x6 x10 x4 K: M5/M6 Washer L: M8 Washer / Lag Bolt Washer M: Lag Bolt x6 N: Concrete Anchor E: M8 x 20mm Bolt x2 O: Allen Key P: TV Bracket Wall Plate Required Tools Socket set 3 Phillips Screwdriver Hammer (for concrete in
Step 1: Attach TV Brackets There are a wide variety of TVs available that require an assortment of bolt sizes. We provide a selection of mounting bolts to fit most TVs. If you have any concerns about this mounting hardware or installation call us direct at 1-888-8482643 or email at support@kantoliving.com. Step 1.1 Select the correct size of bolt Kanto provides 3 bolt diameters (Metric sizes M5, M6 and M8) in various lengths. Part items: A, B, C, D, E, F, or G.
Step 2: Mount Wall Plate Before you start drilling, attach the Wall Plate Template to your wall. It will make marking and drilling level pilot holes easier, and catch a lot of the dust. Remember to remove it before you attach the wall plate! Wood Stud Wall Brick or Concrete Wall The Wall Plate must be mounted to two wood studs. Use a stud sensor to locate the two studs, clearly marking the centers of the studs. Use a long level to make sure these marks are horizontally level.
CAUTION Read this section carefully prior to install. Step 3: Attach TV to TV Plate With the TV brackets firmly secured to the TV, use two people to lift the TV into position and hook the TV brackets onto the TV plate, as shown in Diagram D. Tighten safety bolts at the bottom of the TV brackets as shown in Diagram E.
Step 5: Tilt the TV The FMX2 will tilt +14°/-8° to provide the ideal viewing angle. Loosen the tilt lever on the right side by rotating it counter-clockwise from bottom to top as shown in Diagram H. (Loosen the tilt lever on the left side by rotating it counter-clockwise from top to bottom). To loosen further, flip the lever to avoid contact with the TV plate. Tilt the TV to the desired angle, then tighten the tilt levers by rotating them clockwise.
Check out more great products from Kanto! Kanto Speakers • Check out our full line of bookshelf and desktop speaker systems • Available in a stunning array of colors • Visit kantospeakers.com for more! + + by SP26 • Full line of Audio and Video Cables • White or Black Cables available • HDMI, Optical, Mini-jack, RCA, USB • Switchers, Hubs, and Adapters • Visit kantoliving.com To learn more about all our products, visit www.kantoliving.