Setup guide

ManualsBrandsKanexPro ManualsAV extendersVGAEXTX2

Table of Contents

1) Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2) Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

3) Package Contents . . . . . . . . . . . . . . . . . . . . . . . . 2

4) Unit Layout & Description . . . . . . . . . . . . . . . . . . . 3

5) Connection andOperation . . . . . . . . . . . . . . . . . . . 3

6) ConnectionDiagram. . . . . . . . . . . . . . . . . . . . . . . 4

7) Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Notice

KanexPro™ reserves the right to make changes in the hardware, packaging and any accompanying docu-

mentation without prior written notice.

Introduction

1x2 VGA Extender over CAT5/6 with Audio up to 1,000ft. (300m)

e KanexPro 1x2 VGA extender over CAT5e/6 cable is designed for routing two high-resolution VGA

signals and stereo audio over remote distances up to 1,000ft. (300m). Each receiver set features a separate

gain and peaking rotary switch used in adjusting brightness and skew over long distances. e 15-pin

HD connectors are convenient and cost-eective for all input/ output connections supporting full band-

width compatible from VGA to WUXGA graphics card resolutions and HDTV’s to projectors. In addi-

tion, each output performs a separate buering to maintain signal integrity and reject noise interference.



Features:

• Extendtwoindependenthigh-resolutionVGAsignalwithaudiooverCat5e/6cableupto

1,000 feet (300m)

• AdjustGAINandPEAKlevelstoadaptforvariablelengthsofUTPcableonthereceiverside

• SupportsmaximumresolutionsuptoWUXGA(1920x1200@60Hz)

• Stereoaudiothrough3.5mmjack

• Dualoutputfortransmitter:VGAforlocaldisplayand2xCat5e/6

• EDIDCompliant

• Rackorunder-deskmountable

• 5VDCexternalpowersupplyincluded

Setup Guide

VGAEXTX2

Summary of content (5 pages)

PAGE 1
TM VGAEXTX2 Setup Guide Table of Contents 1) 2) 3) 4) 5) 6) 7) Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . 2 Unit Layout & Description . . . . . . . . . . . . . . . . . . . . 3 Connection and Operation . . . . . . . . . . . . . . . .
PAGE 2
Specifications Transmitter(TX) Input: VGA x1/3.5mm Stereo x1 Output: Cat 5e/6 x2/VGA Output (Local) x1/3.5mm Stereo x1 Interface: Receiver (Rx) Input: Cat 5e/6 x1 Output: VGA x1/3.
PAGE 3
4 Unit Layout & Description VGA Input VGA Output Transmitter Front Back VGA Input VGA Input VGA Output 1 1) 2) Output 3) 4) 5) Output 1 Output 2 3 4 2 5 Video/Audio Input a. VGA Connect to VGA source (TV, Monitor, Projector, etc) using a VGA 15 pin Male to Male cable for video and Input VGA Input 3.5mm Stereo Male to Male cable for audio. Video/Audio Output a. Connect to VGA display (TV, Monitor, Projector, etc) using a VGA 15 pin Male to Male cable for video VGA Output Power Input and 3.
PAGE 4
5 Connection and Operation 1) 2) 3) 4) 5) 6) Connect VGA source(PC, laptop, etc) and the 3.5mm audio cable to the VGA and stereo audio input of the VGA Extender Tx unit. Connect CAT5 output from the Tx to the VGA Extender Rx unit using a UTP Cat5e/6 cable. Plug local VGA display to the VGA Output and Audio Out on the Tx unit. Connect VGA display(Monitor, Projector, etc) to the VGA output on the Rx unit as well as the audio out to the display. Add power supplies to the Tx and Rx units.
PAGE 5
7 Warranty A. Limited Warranty KanexPro™ warrants that (a) its products (the “Product”) will perform greatly in agreement with the accompanying written materials for a period of 12 months (1 full year) from the date of receipt and (b) that the product will be free from defects in materials and workmanship under normal use and service for a period of 1 year. B.