User's Manual

ManualsBrandsKamoer Fluid Tech ManualsElectronicsX1 PRO T Stepper Micropump

X1 PRO T User Manual 2022-03-11
 1 Reading Tips
 1.1 FCC warning
 1.2 User instruction
 1.3 Download Kamoer Remote App
 1.4 Get the tutorial
 2 product description
 2.1 Introduction
 2.2 Feature highlights
 2.3 Application occasion
 2.4 Unpacking preparation
 2.5 Part Name
 2.6 Status indicator description
 3 Product Installation
 4 App use
 4.1 Connect the Micropump to the cloud
 4.2 Binding Micropump
 4.3 Overview of Micropump control interface
 4.4 Schedule dosing-Schedule Setting Details Page
 4.5 Schedule dosing-Schedule Settings
 4.6 Manual dosing page
 4.7 Continuous mode page
 4.8 Settings page
 4.9 time setting
 4.10 Flow Calibration
 4.11 Firmware upgrade
 5 Appendix
 5.1 Technical Parameters
 5.2 After-sales warranty information
 6 update record
1 Reading Tips
1.1 FCC warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television
reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the
following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the device and receiver. --Connect the device into
an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment
FCC Radiation Exposure Statement The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all
persons and must not be co-located for operating in conjunction with any other antenna or transmitter.
1.2 User instruction
Kamoer provides the following documents for users of X1 PRO T Micropump：
1.  《X1 PRO T User Manual》
2.  《X1 PRO T Quick Start Guide》
It is recommended that users first read the 《X1 PRO T Quick Start Guide》 to understand the usage process. For detailed product information, please
read "X1 PRO T Micropump User Manual".
1.3 Download Kamoer Remote App
1.  Scan the QR code to download the application corresponding to the following icon。
1.  Go to App Store or Google Play, search "kamoer remote" to download.
Kamoer Remote App supports Android 4.4 and above systems, and supports iOS 9.1 and above  systems。。
1.4 Get the tutorial
On the device list page, click the "?" icon in the upper right corner to enter the "Tutorial" page, and select "X1 PRO T" to view the tutorial. The tutorial
includes the user manual and frequently asked questions .

Summary of content (13 pages)

PAGE 1
X1 PRO T User Manual 2022-03-11 1 Reading Tips 1.1 FCC warning 1.2 User instruction 1.3 Download Kamoer Remote App 1.4 Get the tutorial 2 product description 2.1 Introduction 2.2 Feature highlights 2.3 Application occasion 2.4 Unpacking preparation 2.5 Part Name 2.6 Status indicator description 3 Product Installation 4 App use 4.1 Connect the Micropump to the cloud 4.2 Binding Micropump 4.3 Overview of Micropump control interface 4.4 Schedule dosing-Schedule Setting Details Page 4.
PAGE 2
product description 2.1 Introduction X1 PRO T is a single-channel WIFI Micropump, remotely controlled by mobile phone App, using a longer-life stepping motor, can be used as a dosing pump, can also be used as a calcium back pump; as a dosing pump, it can be flexibly and accurately The marine biological tank supplements various elements needed for the growth of marine organisms, such as calcium, magnesium, KH enhancer, trace elements, etc.
PAGE 3
2.
PAGE 4
1-2. Open the App, click the "+" button in the upper right corner of the device to add a device, enter the add device interface, select "KamoerX1PRO" in the list of supported devices and click to enter; 3.Make sure that the mobile phone is connected to the WiFi that needs the network, and that the WiFi can be connected to the external network, (the device does not support 5G Wi-Fi, and 5G Wi-Fi hotspots cannot be used)； 4.
PAGE 5
7. Click "Start using" on this interface to enter the device list interface. At this time, the red status indicator light is on, which means the dosing pump has been connected to the cloud and the user has completed the binding with the Micropump。 prompt a. Configure the device to connect to Wi-Fi only once. After the configuration is successful, as long as the App can connect to the Internet, you can find the device in the device list after opening the App。 b.
PAGE 6
3.After the binding is successful, a successful binding prompt will pop up, click Start to return to the device list； 4.3 Overview of Micropump control interface Open the App, click on the Micropump in the device list to enter the Micropump operation interface. The Micropump operation interface contains the running function and setting function： a. Plan： indicates the current working mode, where you can switch the working mode.
PAGE 7
Click on the plan in the bottom navigation bar to enter the plan details page. The plan details page contains the following functions： a.
PAGE 8
a.Create a plan groupv:In the channel plan details page, click the "+" add button in the upper right corner to enter the plan group add interface； b.Set the name of the plan group:Used to distinguish and identify other plan groups； c.Set the time period range of the plan group:After the time period range is set, the plans created in the group will be executed in this time period. The maximum time period range is 00:00~23:59 ； d.
PAGE 9
time of the plan, and the other is the amount of plan added； f.Quick plan add entry: Multiple plans can be added in sequence through quick plan settings； g.Plan start time: Add the start time of a single plan h. Planned amount: Add the amount of a single plan i.Save the plan: Save the plan After the plan is created, you can edit it，Click the plan to be edited to enter the plan editing interface.
PAGE 10
The continuous mode allows the pump to run continuously at a certain speed, and is generally used in calcium reactor applications。 a.Continuous mode: Click to enter continuous mode b.Flow setting:Set the flow of the pump. When the pump is running, it will run at the speed corresponding to this flow. The flow calibration is carried out in Settings -> Flow Rate Calibration； c.Rotation speed: Rotation speed corresponding to flow； d.Pump tube use time:Record the cumulative use time of the pump tube； e.
PAGE 11
a.Device serial number ： b.Current firmware version:Display the current version of the firmware, if the firmware is updated, there will be a prompt below； c.Name: Here you can modify the device name and the name of each pump head to identify the purpose of the device and pump head； d.Serial number:Click to enter the display device serial number； e.Update:Firmware update, if there is a new firmware release, there will be a prompt； f.
PAGE 12
4.10 Flow Calibration The purpose of calibration is to improve the accuracy of added elements; Click "flow rate calibration" in the setting interface to enter the calibration pump head selection interface, select the pump head to be calibrated, and enter the flow calibration interface. Calibration requires the use of a graduated cylinder. The pump is equipped with a 10ML graduated cylinder when it leaves the factory.
PAGE 13
5 Appendix 5.1 Technical Parameters Dimensions (LengthWidthHeight)** 100 x 92 x 63 mm (including pump head) Weight 316g (not including power adapter) Power Adapter Input: 100VAC -240VAC Output: DC12V 2A Titration parameters Dosing channel: 1 KFS pump head Flow rate: >70ml/min Number of titrations: 24 times/day-1 time/99 days Dosing accuracy: <±2% Volume range: 0.1 ml-9999.