User's Manual

ManualsBrandsKamoer Fluid Tech ManualsElectronicsX1 PRO 2 Dosing Pump

X1 PRO 2 User Manual 2022-03-11
 1 Read the Tips
 1.1 FCC warning
 1.2 Use Recommendations
 1.3 Download Kamoer Remote App
 1.4 Get the Tutorial
 2 Product Overview
 2.1 Introduction
 2.2 Feature Highlights
 2.3 Applications
 2.4 Out of the Box
 2.5 Part Name
 2.6 Status LED Description
 3 Product Installation
 4 App Use
 4.1 Connect titration pumps to the cloud
 4.2 Binding titration pump
 4.3 Overview of the titration pump control interface
 4.4 Plan Titration - Plan Settings Details Page
 4.5 Plan Titration - Plan Settings
 4.6 Manual Titration Page
 4.7 Set Up the Page
 4.8 Time settings
 4.9 Flow Calibration
 4.10 Firmware Upgrades
 5 Appendix
 5.1 Technical Parameters
 5.2 After-sales Warranty Information
1 Read the Tips
1.1 FCC warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television
reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the
following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the device and receiver. --Connect the device into
an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment
FCC Radiation Exposure Statement The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all
persons and must not be co-located for operating in conjunction with any other antenna or transmitter.
1.2 Use Recommendations
Kamoer provides the following documentation for X1 PRO 2 titration pump users:
1.  《X1 PRO 2 User Manual》
2.  《X1 PRO 2 Quick Start Guide》
It is recommended that users first read the X1 PRO 2 Quick Start Guide to understand the usage process. For detailed product information, please read
the X1 PRO 2 titration pump user manual.
1.3 Download Kamoer Remote App
1.  Scan the QR code for the app download of the following icon.
1.  Apple users go to the App Store, Android users enter the Baidu App Store, search for "Kamoer Remote" and find the app for the corresponding
icon download.
The Kamoer Remote App supports Android 4.4 and abov e, and iOS 9.1 and above.
1.4 Get the Tutorial
After installing the app open, click the button in the upper left corner of my module on the device list page to enter my module, click on the tutorial in my
module, enter the tutorial module, click into the corresponding device model, including user manual and common question syllables.

Summary of content (12 pages)

PAGE 1
X1 PRO 2 User Manual 2022-03-11 1 Read the Tips 1.1 FCC warning 1.2 Use Recommendations 1.3 Download Kamoer Remote App 1.4 Get the Tutorial 2 Product Overview 2.1 Introduction 2.2 Feature Highlights 2.3 Applications 2.4 Out of the Box 2.5 Part Name 2.6 Status LED Description 3 Product Installation 4 App Use 4.1 Connect titration pumps to the cloud 4.2 Binding titration pump 4.3 Overview of the titration pump control interface 4.4 Plan Titration - Plan Settings Details Page 4.
PAGE 2
Product Overview 2.1 Introduction X1 PRO 2 is a single-channel intelligent titration pump with WIFI remote function, mainly used to add the various elements needed for marine life growth, such as calcium, magnesium, KH booster, trace elements, etc. to marine life cylinder timing, quantitative and accurate. The automation of X1 PRO 2 can greatly reduce the amount of manual added work, but also avoid manual addition caused by leakage, adding excessive or insufficient errors. 2.
PAGE 3
2.
PAGE 4
1-2.Open the app, click the “+” button in the upper right corner of the device to add the device, enter the Add Device interface, select “KamoerX1PRO” in the list of supported devices and click to enter; 3.Make sure that the mobile phone connection requires WiFi with the network, and that the WiFi can be connected to the external network. (The device does not support 5G WiFi and cannot use 5G WiFi hotspot); 4.
PAGE 5
.Long press and hold on the rear panel on the "Reset" button more than 4 seconds after release, wait 3 seconds, at this time the blue state light flashes quickly, the device into the distribution network state, in the device distribution network state, click on the App "light is flashing fast" button to start the distribution network; 6.Wait for the network connection successfully, after the connection is successful, the app will pop up the interface of the connection success; 1.
PAGE 6
3.After the binding is successful, the binding success prompt pops up, clicks to start, and returns to the device list; 4.3 Overview of the titration pump control interface Open the app, click on the titration pump in the device list to enter the titration pump operating interface, titration pump operator interface contains three modules: a.
PAGE 7
Click on the plan in the bottom navigation bar to go to the plan details page, which includes the following features: a.
PAGE 8
g.Delete the plan： Click on the plan group to swipe left, will appear the plan group delete button, click delete button, plan group delete, the group's plan is also deleted; 2.Plan within the group to create, edit, delete The planned operation is carried out within the planning group. The plans of all groups in each channel can add up to 24 plans. The following describes the related operations of the plan: a.Number of plans: Displays the number of plans within the plan group; b.
PAGE 9
The quick plan can add multiple in-group plans at a time to meet the convenient operation requirements of adding multiple plans at a time. When you need to add a shortcut plan, click “Quick Add” below the plan list to enter the shortcut plan add interface: * a.Number of additions： The number of plans that need to be added; * b.Total additions： The total amount of addition that needs to be added; * c.
PAGE 10
a.Device serial number ： b.Current version of firmware ： Show the current version of the firmware, if the firmware has an update, there are tips below; c.Name ： Here you can modify the device name and the name of each pump head to identify the purpose of the device and pump head; d.Serial number： Click to enter the display device serial number; e.Update ： Firmware update, if there is a new firmware release, there will be a prompt; f.
PAGE 11
a. Flow rate calibration： Click on the flow rate calibration in the settings interface to enter the flow rate calibration interface; b. Start emptying： The purpose of emptying is to let the air in the pump tube drain, so that the accuracy of the rear calibration will not be affected; c. Drop timing： Set the running time of the pump during calibration; Before proceeding to the next step, make sure that the pump pipe inlet has been immersed in water, the pump pipe outlet is placed in the measuring tube; d.
PAGE 12
Warranty free service is limited to the user manual under normal use and maintenance is effective, all person for failure or damage is not covered by the warranty. Users please take good care of the purchase of machine invoices, user manuals, so that you can get satisfactory after-sales service in a timely manner. 2. Warranty Coverage Within one year from the date of purchase, the Company will provide free warranty service in the event of any damage caused by manufacturing processes or components.