User's Manual

ManualsBrandsKami ManualsCamera & PhotoKami Doorbell Camera

Table Of Contents

D201V2.2

Website:www.kamihome.com

E-mail:support@kamihome.com

https://kamihome.com/legal/fcc

D201 Kami Doorbell Camera User Manual

165×165mm

PANTONE 541 Ul

PANTONE Cool Gray 11 C+Kl

68g晨鸣云镜双胶

图号

料号

D20

609

骑马钉装订（两钉）

DoorbellCamera

InstallationGuide

2020/08/07 新建

2020/08/11 1. 二极管安装图示修改 2. 认证编号更新 3. 安装定位线图示更新

4. 背板上墙图示更新 5. 尺寸更新 6. 安装顺序调整 7. 安全提示

8. 文字更新 9. 版本更新。

2020/08/12 1. 文字更新 2.版本更新

2020/08/13 1. 11页加一段话 2.版本更新

2020/08/14 1. 电话改回 2. 版本升级

2020/09/03 1.语音播报更新 2. 版本升级

2020/09/16 1.第 9页文字翻译调整 2. 版本升级（V1.8）

2021/01/22 1.翻译大调整 2. 增加两个配件图示及说明 3. 第8页图示更新

4. 14-16页线条调整 5. 去掉FCC ID 6. 版本升级

2021/03/04 1. 封底去掉认证信息 2. FCC ID更新 3.版本更新

2021/04/07 1. 更新FCC ID 2. 增加IC认证编号及声明 3. 版本更新

Summary of content (10 pages)

PAGE 1
D201 Kami Doorbell Camera User Manual Doorbell Camera Website: www.kamihome.com E-mail: support@kamihome.com https://kamihome.com/legal/fcc Installation Guide D201 V2.2 2020/08/07 新建 2020/08/11 1. 二极管安装图示修改 2. 认证编号更新 3. 安装定位线图示更新 4. 背板上墙图示更新 5. 尺寸更新 6. 安装顺序调整 7. 安全提示 8. 文字更新 9. 版本更新。 2020/08/12 1. 文字更新 2.版本更新 2020/08/13 1. 11页加一段话 2.版本更新 2020/08/14 1. 电话改回 2. 版本升级 2020/09/03 1.语音播报更新 2. 版本升级 2020/09/16 1.第 9页文字翻译调整 2. 版本升级（V1.8） 2021/01/22 1.翻译大调整 2. 增加两个配件图示及说明 3. 第8页图示更新 4. 14-16页线条调整 5. 去掉FCC ID 6.
PAGE 2
. Getting to Know Your Doorbell Camera 1.
PAGE 3
. Charge + Insert battery a. Charge the Battery Power Connector Tamper Button Power Indicator Please charge the battery, using a micro USB cable. and a power adapter (not included). The indicator light will be red while charging and turn white when fully charged. Reset Button Speaker b. Remove the Protective Cover Press down on the face of the doorbell with your thumbs and pull the outer protective cover up and away from the main body, as shown in the diagram on the left.
PAGE 4
c. Installing the Battery 4. Pairing Your Doorbell Camera After removing the protective cover, push the battery into the battery compartment as shown. (Ensure that the battery is inserted in the correct direction with pins facing up) Push the tab shown in the diagram below to free the battery. Pull the battery straight down to remove. Step 1 Download the Kami Home / YI Home App and sign up or sign in to your existing account.
PAGE 5
Step 5 Tap the "Next" button and wait until you hear the message "Pairing is successful" both from the camera and from the app. Assign your desired name to the Doorbell and tap "Save". You will hear "You may start using your camera now". c. Mechanical Doorbell Setup: Installing the chime connector (optional) If you are using a mechanical chime, please install the chime 1 connector to ensure a stable power supply.
PAGE 6
d. Height and Distance Recommendations e. Suggested Installation Angle The optimal detection range for the Kami Doorbell Camera is 0-4m / 0-13ft. Additionally, we recommend you install the doorbell at a height of 1.2m / 4ft to ensure the ground in front of your door can be captured. Your Kami Doorbell Camera comes with three diﬀerent backplates that can be used to help place your camera at Flat Backplate #1. If you don't want to change the camera's angle, use Flat Backplate #1.
PAGE 7
f. Fixing the Backplate to the Wall (optional) Take out the backplane and lay it ﬂat on the wall where Doorbell is to be installed. Take a pen and press it ﬁrmly into the center of the two holes in the back panel to mark the wall. Note: Installing your camera on wood doesn't require screw anchors.
PAGE 8
g. Connecting the Doorbell wires and (2) Extension Wires (optional) You connect each of the wires to either of the screws in the back. The order does not matter. If your wires are too short and you have trouble connecting the wires coming out of the wall to the back of the doorbell, please use the included Extension Wires and wire nuts. (See Picture) . h.
PAGE 9
Mount the Doorbell to an Angled Backplate: Horizontal Angle Backplate #2 Battery 2 1 I. Install the Front Panel Use Screw A to keep the Doorbell Front Panel in place.
PAGE 10
j. Turning the Power On FCC COMPLIANCE STATEMENT: To complete the installation process, please switch the power back ON and test the operation of your Doorbell. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.