INSTRUCTION BOOKLET Suits all KFA839 models
Important Please retain your instruction book for future use. In the event that you need some assistance with your Kambrook appliance, please contact our Customer Service Department on 1300 139 798 (Australia) or 0800 2738 45 (New Zealand). Alternatively, visit us on our website at www.kambrook.com.au or www.kambrook.co.
Contents Kambrook Recommends Safety First p4 Your Kambrook Arctic Remote Controlled Tower Fan p6 Quick Start Guide p8 Using Your Kambrook Tower Fan p9 Care, Cleaning and Storage p14
Kambrook Recommends Safety First IMPORTANT: Please retain your instruction book for future use. At Kambrook, we believe that safe performance is the first priority in any consumer product, so that you, our valued customer can confidently use and trust our products. We ask that any electrical appliance that you use be operated in a sensible fashion with due care and attention placed on the following important operating instructions.
Important Safeguards For All Electrical Appliances • Fully unwind the power cord before use. • Connect only to a 230V or 240V power outlet. • Do not let the power cord hang over the edge of a bench or table, touch hot surfaces or become knotted. • To protect against electric shock, do not immerse the power cord, power plug or appliance in water or any other liquid or allow moisture to come in contact with the part, unless it is recommended in the cleaning instructions.
Your Kambrook Arctic Remote Controlled Tower Fan 1. LED screen 2. Control panel featuring: • POWER On/Off button • Fan SPEED button (Includes 3 speed settings; low, medium and high) • MODE button (includes 3 cooling modes; normal, nature and reduction mode) • TIMER button (up to 12 hours) • OSC button to set oscillation 3. Tower fan body 4. Remote control signal receiver 5. Oscillating platform 6. 2 piece base stand (a) and (b) 7.
Quick Start Guide Turning the tower fan on a vv Plug the power cord into a 230V or 240V power point and switch on. Once the power outlet is switched on, this will automatically illuminate the LED screen to display to current room temperature. SEE NOTE To start the tower fan, turn the tower fan on by pressing the ‘POWER’ button once; the unit will be in NORMAL fan mode, at LOW speed setting. SEE NOTE Pressing the ‘SPEED’ button twice will set the tower fan into HIGH speed setting.
Using Your Kambrook Tower Fan Before first use Remove your tower fan from its carton and associated protective wrapping. Unwind the cord to its full length and remove any protective cardboard or foam that may have been used to minimise transportation damage. Once assembled by following the directions below, place the tower fan on a firm, level surface in a stable upright position. Visually inspect the air inlet and outlets to ensure no foreign material is blocking these areas.
Using Your Kambrook Tower Fan 4. Position base stand piece (b) with the curved side facing towards the bottom part of the tower fan body, onto base stand piece (a) by interlocking the four locating posts located along the straight edge of each of the base stand pieces and by aligning the two remaining screw posts located underneath the tower fan body with the corresponding screw posts on base stand piece (b). Firmly push down base stand piece (b) until it is secured into place with base stand piece (a).
Turning Your Tower Fan On Setting the Fan Speed To operate the tower fan, plug the power cord into a 230V or 240V electrical outlet and switch the outlet on. Be sure the plug fits tightly as a loose fit will cause overheating and damage the plug. The tower fan has three fan speed settings; LOW , MEDIUM and HIGH . Once the power outlet is switched on, the fan is in ‘Standby’. When in standby, the fan is not turned on but the LED screen will illuminate displaying the current room temperature only.
Using Your Kambrook Tower Fan continued Nature Mode Reduction mode The NATURE mode simulates the natural rise and fall of the wind over time, with speed settings automatically cycling between low, medium and high. The REDUCTION mode allows you to pre-select a variation in speed which automatically decreases the fan speed over time. At any fan speed setting, pressing the MODE button once will turn the tower fan into NATURE mode.
NOTE: When the NATURE mode setting is selected, the tower fan is programmed to self-regulate through the various fan speeds. The NATURE mode is independent from the fan speed settings while the LED screen will still display the last selected fan speed setting. NOTE: The tower fan is fitted with a power saving feature.
Care, Cleaning and Storage 1. 2. 3. 4. Ensure that the tower fan is switched OFF and disconnected from the power outlet before cleaning. Use a clean, dry cloth to clean the external surfaces of the tower fan. If the tower fan has collected dirt inside the unit, have the unit cleaned by a qualified service agent. Do not operate the tower fan in this condition. Do not attempt to open the case of the tower fan at any time as there are no customer serviceable parts inside.
Notes 14
Notes 15
Kambrook - Australia Ground Floor, Suite 2, 170-180 Bourke Rd Alexandria NSW 2015, Australia Locked Bag 2000 Botany NSW 1455 Customer Service Line 1300 139 798 Customer Service Fax 1800 621 337 www.kambrook.com.au Kambrook - New Zealand Private Bag 94411 Botany, Manukau Auckland 2163 New Zealand Customer Service Line/ Spare Parts 0800 273 845 Customer Service Fax 0800 288 513 www.kambrook.co.