E-730 Series 630 Series 750 Series INSTALLATION GUIDE Exit Device Operators - Generation E-730 / 630 / 750 / 79E Series Technical Support: 1.800.906.4526 Customer Service: T: 1.877.468.3555 F: 514.735.6589 General Information: www.kabailco.com Online Consumable Orders: www.keycard.com To access all of our easy steps,please visit our Support Website: http://connect.kabalodging.com PK2925-T _11_07 Printed in Canada KabaIlco Inc. 7301 Boul.
Note for Contactless 790 customers: Statement according to FCC part 15.105 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
I Ch e ckli st for pr e ci si on Ex i t De vi ce s 21/22/FL21/FL22 H VON DUPRIN 98/99EO-F/9827/9927 EO-F M G ** DETEX 10/F10/20/F20 F How to change lock cylinders (continued) 31. Re-insert the cylinder plug (Fig. 19) Fig. 19 ! W Important: The Key Override itself does not retract the latch or deadbolt. Do not use too much force when turning the key as this may damage the unit. To retract the latch, turn the key clockwise until it stops, release the key and turn the lever handle (H).
I C h ec kl is t f o r s t a n d a rd E x i t Devices 10. How to change lock cylinders Test the Mechanical Override Function (continued) D ! B 24. Remove the cap from the lever handle (see step 20, Fig. 16). Verify the functionality of the override after the lock is installed on the door: 25. Insert key. 26. Turn the key clockwise until it stops. 27. Release key. J 28. Use a small flat screwdriver to push in the lever catch through the small hole underneath the lever handle (Fig. 17). 19.
6. Verify the attachment of the lever handle ! 8. test the mechanical override function Very Important: To verify that the lever handle has been correctly attached to the housing: 10. Remove key 11. Insert a small flat screwdriver (tool T, page 11) into the hole on the underside of the lever handle and push in the lever catch. 12. Pull on the lever handle. * This test can only be performed when the lock is not affixed to the door.
5. Attaching the Lever Handle to the Lock (with the key as shown in Fig. 6 & Fig. 7) III INSTALL THE E - 7 3 0 / 6 3 0 / 7 5 0 / 79E Lo ck a nd t he Exit Device 7. Fit the lever handle onto the drive tube. It should rest approximately 1/16” from the body of the housing. (See Fig. 8) 3 Install the Standard Exit Devices E-730/630/750/79E Outside Housing If it can’t be pushed that close to the housing, the lever catch is probably not pushed in. Push it in.
3. Preparing the lever handle and cylinder for installation 3. Insert the cylinder into the lever handle (see Fig.3) Fig. 3 4. Steps to attach the lever handle to the lock housing *NOTE: the position of the key is very important 6. Right-handed Lever handle: Turn the key aprroximately 90º to 100º clockwise so that it is in the vertical position and the countersink is in the top position. (See Fig. 6) Fig.
5 Install the Outside Lever 1. Upon unpacking, the E-730/630/750/79E lock housing with mechanical override should look like the diagram below with: Access Hole (A) The small indents on the cross of the override shaft in line horizontally (B) The nylon washer and the spring washer on the drive tube (C) The lever catch in the out position (D) Cylinder and 2 keys for 630 K/C included in the hardware bag The lever is field reversible.
VIII I nstal la t i o n o f t h e me c ha nica l o verride o n 730/ 630/ 750/ 79E IV Te st th e ope r ati on of th e E-730/750/79E lock Parts and Tools List Tools Required: (U) Cylinder (provided with lock) or equivalent ! (E) (F) (G) (H) Drive tube Lever catch Countersink Lever handle (I) (J) (K) (L) A Panic Bar Activate the panic bar. The latch bolt or rod retracts fully. Turn the outside lever downward while the green LED is flashing. The latch or rod retracts fully.
VI O per a ting t h e E me rg e n cy O v e r ride ( F or mechan ical override models , see S ectio n ViI I , step8) If the lock will not respond to any keycard (including the Emergency keycard), there are three options that should be attempted to open the door. In order, they are: 1. Verify the batteries, and replace them if they are providing less than 4 Volts total. Insert the Initialization keycard in the lock, then use the Emergency keycard. 2.