Operating Instructions

Battery Handling and Usage
• Install the battery observing the positive (+) side up as indicated
inside the battery compartment.
• Never throw batteries into a fire. Do not expose batteries to fire or
other heat sources.
• Battery contains mercury. Do not put in trash. Recycle or manage
as hazardous waste.
• Remove the battery compartment cover away from the remote (see
diagram below)
• Remove the old battery and place a new Type 3V (CR2032) lithium
battery into the battery compartment.
• Ensure the battery is installed correctly with the
positive (+) side up.
• Replace the battery compartment cover.
• Dispose or recycle
spent/discharged batteries
in compliance with all
applicable laws. For detailed
information, contact your
local solid waste authority.
Caution: Failure to properly
align the battery polarity can
cause personal injury and/or
property damage.
+
CR2032
3V
RECEIVER MODEL: TM-110
TRANSMITTTER MODEL: TR-034-7
FCC ID: PAGTR-034-7
WARNING:
Do not ingest the battery, Chemical Burn Hazard (The remote control
supplied with) This product contains a coin/button cell battery. If the
coin/button cell battery is swallowed, it can cause severe internal
burns in just 2 hours and can lead to death. Keep new and used
batteries away from children. If the battery compartment does not
close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any
part of the body, seek immediate medical attention.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
FCC Caution: Any changes or modifications not expressly approved
by the party responsible for compliance could void the user's
authority to operate this equipment.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits
for Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
Outdoor Remote Control
Countdown Timer
HODT12B
CAUTION
• Suitable for use with outdoor appliances.
• For use ONLY with a three conductor GFCI protected outlet.
• Raintight when mounted vertically with receptacles facing
downward.
• Do not immerse in water.
• DO NOT EXCEED RATED CAPACITY.
• The device must be mounted in a vertical position with the
receptacle facing downward and with the receptacle at least
2 FT above the ground level.
• Cord-connected Operating Control.
• Temperature limits of the SWITCH HEAD: -40-40ºC.
Receiver
Transmitter
power sensor
2 Hrs 4 Hrs
6 Hrs 8 Hrs
2
1
3
4
5
1. Sensor ( ):
Sensor will turn receiver on at dusk and off at dawn.
2. Operating Mode:
Timer will turn ON, 2, 4, 6, or 8 hours after dusk.
3. Select button:
To select the function and repeatedly.
Power ON Sensor ( ) 2H 4H 6H 8H OFF ON
4. Outlets:
Plug the lights or devices to be controlled by the timer into one of
the outlets.
5. Transmitter
1. Mount or hang the RECEIVER on the wall near a GFCI protected
outlet (125V 60Hz) which the power supply cord of the RECEIVER
will plug into.
2. Plug the cord of the device you wish to control remotely at the
bottom of the RECEIVER.
Receiver & Transmitter operation modes:
ON: Power is ON to attached devices
Sensor ( Dusk - Dawn): power will turn on at dusk and remain on
until dawn
2 Hrs: Power will turn on at dusk and remain on for 2 hours
4 Hrs: Power will turn on at dusk and remain on for 4 hours
6 Hrs: Power will turn on at dusk and remain on for 6 hours
8 Hrs: Power will turn on at dusk and remain on for 8 hours
OFF: Power is OFF to attached devices
* Note for Transmitter: Control electrical outlet up to a distance of
100 feet.
* Note The timer has daily repeat after setting, in case of power
failure, it will stop operating when the power goes out. Once power
is restored, reset the desired operating mode as the operating
instructions.
• In the sensor ( dusk-to-dawn) mode, temporary light sources like
headlights, porch lights and other external light sources will not
interfere with the photocell function unless the external light source
is on for more than 15 minutes. In that case, the timer will shut off
until darkness is restored. The improvement avoids the flickering.
• Once programming activates at dusk in the 2hr, 4hr, 6hr, or 8hr
mode, the program cycle will complete before the timer resets.
Headlights, porch lights, street lamps and other external lighting
sources will not interfere with the active timer program.
Helpful Tips
• When set to “ON”, the timer will provide continual power to
attached devices until the timer is switched to “OFF”, or to any of
the other operating modes.
OFF
ON
2H
6H
8H
4H
1
OFF
ON
2H
6H
8H
4H
+
CR2032
3V
DO NOT ATTACH A DEVICE THAT EXCEEDS THE UNIT RATINGS:
125 V ac 60 Hz,
15 A Resistive,
15 A General Use,
1000 W Tungsten,
500 VA Electronic Ballast, 1/2HP.
120 V ac, 60 Hz, 8.3 A Ballast