User's Manual

ManualsBrandsKAB ManualsElectronicsRemote Controller

2Hrs 4Hrs

6Hrs 8Hrs

power sensor

3 OUTLET WIRELESS

REMOTE WITH TIMER

WARNING:

• The device must be mounted in a vertical position with the receptacle facing

downward and with the receptacle at least 2 feet above the ground level not

for water immersion.

• Cord-connected Operating Control.

• Temperature limits of the SWITCH HEAD: -40-40

INSTALLATION INSTRUCTIONS

Button Layout

Safety Information

RECEIVER MODEL #RC-021

TRANSMITTER MODEL #TR-033-7

FCC ID: PAGTR-033-7

IC : 4494A-TR0337

SPECIFICATIONS: 14/3 AWG SJTW vinyl cord

RATINGS: 125Vac, 60Hz,

15 A General Purpose, 15 A Resistive,

1,000 W Tungsten,

500 VA Electronic Ballast, 1/2 HP,

120Vac, 60Hz, 8.3A Ballast.

1. Sensor:

Sensor will turn receiver on at dusk

and off at dawn.

2. Operating Mode:

Timer will turn ON, 2, 4, 6, or 8 hours

after dusk.

3. Select button:

To select the function and repeatedly.

Power ON Sensor 2H 4H 6H

8H OFF ON

4. Outlets:

Plug the lights or devices to be

controlled by the timer into one of the

outlets.

5. Transmitter

Receiver

Transmitter

Battery Handling and Usage

Keep batteries away from children and pets.

• Follow the battery manufacturer’s safety and usage instructions.

• Insert the battery observing the proper polarity (+/-) as indicated inside

Battery Compartment.

• Never throw batteries into a fire. Do not expose batteries to fire or other

heat sources.

• Dispose or recycle spent / discharged batteries in compliance with all

applicable laws. For detailed information contact your local solid waste

authority.

• Battery contains mercury. Do not put in trash. Recycle or manage as

hazardous waste.

WARNING:

CAUTION

• Suitable for use with outdoor appliances.

• For use ONLY with a three conductor GFCI

protected outlet.

• Raintight when mounted vertically with receptacles

facing downward.

• Do not immerse in water.

• DO NOT EXCEED RATED CAPACITY.

Installation

1. Mount or hang the RECEIVER on the wall near a GFCI protected outlet

(125V 60Hz) which the power supply cord of the RECEIVER will plug

into.

2. Plug the cord of the device you wish to control remotely at the bottom of the

RECEIVER.

Operating Instructions

Receiver & Transmitter opetation modes:

ON: Power is ON to attached devices

Sensor(Dusk - Dawn): power will turn on at dusk and remain on until dawn

2 Hrs: Power will turn on at dusk and remain on for 2 hours

4 Hrs: Power will turn on at dusk and remain on for 4 hours

6 Hrs: Power will turn on at dusk and remain on for 6 hours

8 Hrs: Power will turn on at dusk and remain on for 8 hours

OFF: Power is OFF to attached devices

* Note for Transmitter: Control electrical outlet up to a distance of 100 feet.

* Note: In the sensor mode, any external light sources will not interfere with the

photocell function, unless the external light source is on for more than 15

minutes. In that case, the timer will shut off until darkness is restored. The

improvement avoids the flickering.

Helpful Tips

• Once programming activates at dusk in the 2hr, 4hr, 6hr, or 8hr mode, the

program cycle will complete before the timer resets. Headlights, porch lights,

street lamps and other external lighting sources will not interfere with the

active timer program.

• The timer has daily repeat after setting, in case of power failure, it will

stop operating when the power goes out. Once power is restored, reset the

desired operating mode as the operating instructions.

• When set to “ON”, the timer will provide continual power to attached devices

until the timer is switched to “OFF”, or to any of the other operating modes.

SAVE THESE INSTRUCTIONS!

MADE IN CHINA

WARNING: Cancer and Reproductive Harm -

www.P65Warnings.ca.gov

Unique Identifier :

KAB Model No. :

RC-021/TR-033-7

Responsible Party - U.S.

Contact Information

Company Name :

Customer Address :

Tel/Internet Contact :

Battery Replacement:

• Remove the Battery compartment cover from the back of

the remote control.

• Remove the spent battery and place a new Type CR2032

battery into the Battery Compartment correctly observing

the polarity indications (+/-) inside the Battery

Compartment.

• Replace the Battery Compartment Cover.

• Clear the battery contacts and also those of the device

prior to battery installation

Federal Communications Commission Interference Statement

This equipment has been tested and found to comply with the limits for Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference

that may cause undesired operation.