IQ™ DIGITAL LOCK BOX Installation Instructions Important safety instructions - Save these instructions RC 20, 24 CONTENTS PL 16, 20, 24 PC 16, 20, 24 MC 16, 20, 24 DC 16, 20, 24 AC 24 UC 24, 30, 36, 48 Tools Needed - 2 Parts - 2 Notes - 3 Dimensions - 3 Existing Recessed Installation - 4 Existing Surface Installation - 5 New Installation: PLM Cabinets - 6 New Installation: R3 / Uplift Tech - 8 Finish the Installation - 10 Use and Maintenance - 11 Cleaning - 11 Warranty - 11 Compliance - 12 GENERAL I
TOOLS NEEDED PARTS [211-1331] Digital Lock Box Lock Box Shelf [216-1192] Hardware Bag* [216-1193] Quick Start Bag IQ [203-1492] (4) #10 x 3/8" Screw ™ DIGITAL LOCK BOX IQ ™ DIGITAL LOCK BOX [203-1493] (4) #6 x 3/8" Screw USER SET UP GUIDE [SS125] (4) #6 x 3/4" Screw Registration Card [211-1328] (4) Locking Pin [217-1382] Quick Start Guide [211-1325] (2) Mounting Block [203-1510] (2) Lock Box Key *Depending on installation, not all parts will be used. © 2020 Robern, Inc. 701 N. Wilson Ave.
NOTES WARNING! TR UHGXFH WKH ULVN RI HOHFWULFDO VKRFN VKXW Rႇ SRZHU EHIRUH LQVWDOOLQJ LQ DQ HOHFWULFDOO\ SRZHUHG FDELQHW DIMENSIONS 2-7/16" 62 (62mm) 2-7/16" 9-3/8" 238.3 9-3/8" (238mm) 9" 228.6 9" (229mm) 5-1/4" 133.4 (133mm) 5-1/4" © 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A. 800.877.2376 www.robern.com 3 Part no.
EXISTING RECESSED INSTALLATION NOTE: )RU FDELQHWV ZLWK HOHFWULFDO RSWLRQV WXUQ EUHDNHU Rႇ EHIRUH EHJLQQLQJ NOTE: Remove door from cabinets before beginning. 1. Remove four mounting screws from the cabinet box and save for reinstallation of cabinet. 2. Partially remove the cabinet from the rough opening until the required shelf holes are accessible. 1 2 © 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A. 800.877.2376 www.robern.com D4 4 D6 / D8 Part no.
EXISTING SURFACE INSTALLATION 127( )RU FDELQHWV ZLWK HOHFWULFDO RSWLRQV WXUQ EUHDNHU Rႇ EHIRUH EHJLQQLQJ NOTE: Remove door from cabinets before beginning. 1. Remove four screws holding each side kit to the cabinet box and save for side kit reinstallation. 2. Remove side kits and set aside in a safe location. 1 2 © 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A. 800.877.2376 www.robern.com 5 Part no.
NEW INSTALLATION: PLM CABINETS NOTE: Remove door from cabinets before beginning. 1. Using the key provided, open the digital lock box and remove the hardware bag. 2. Remove two of the four screws from each side of the lock box shelf according to your cabinet depth. 1 2 © 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A. 800.877.2376 www.robern.com 6 D4 D6 /D8 D4 D6 / D8 Part no.
NEW INSTALLATION: PLM CABINETS 3. Insert lock box shelf into cabinet at your preferred height aligning it to the shelf pin holes in the cabinet box. 4. Attach the lock box shelf to the cabinet box using the four #6 x 3/4" screws [SS125] provided. 3 4a D4 D4 D6 / D8 4b D6 / D8 127( 3URFHHG WR ¿QDO VHFWLRQ ),1,6+ 7+( ,167$//$7,21 © 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A. 800.877.2376 www.robern.com 7 Part no.
NEW INSTALLATION: R3 / UPLIFT TECH NOTE: Remove door from cabinets before beginning. 1. Using the key provided, open the digital lock box and remove the hardware bag. 2. Position and insert mounting blocks into each side of the cabinet at your preferred height and secure with two screws [203-1493] in each mounting block. NOTE: Arrows on mounting blocks should be pointed toward back of cabinet box. 1 2a © 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A. 800.877.2376 www.robern.
NEW INSTALLATION: R3 / UPLIFT TECH 3. Insert lock box shelf into cabinet slightly above the mounting blocks. Gently press the shelf against the back of the cabinet box and then slide down until the shelf engages with the mounting blocks. 4 Insert the four locking pins [211-1328] provided, two pins per side. 3 4 © 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A. 800.877.2376 www.robern.com 9 Part no.
FINISH THE INSTALLATION 5. Once the shelf is secured, insert the lock box. If your shelf is wider than the lock box, adjust the lock box to your desired position, side to side, within the cabinet. ൧. Secure the lock box into the shelf using the four #10 x 3/8" screws [203-1492] provided. 7. Proceed according to Cabinet's Installation Instructions. 8. To set up and activation of the lock box, refer to the quick start guide. 5 6 © 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A. 800.877.
USE AND MAINTENANCE Please refer to the IQ Digital Lock Box Quick Start Guide [217-1382] for setup and use instructions. When ordering replacement keys, have the Serial Number and Security Registration Code available. This information can be found on the Registration Card and on the label on the rear of the Digital Lock Box. NOTE: It is strongly recommended that the Registration Card be kept in a safe place for future reference. CLEANING Use only a damp cloth to clean.
COMPLIANCE RF Exposure Statement This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. This equipment meets the exemption from the routine evaluation limits in section 2.5 of RSS-102. It should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.
BOÎTE VERROUILLÉE NUMÉRIQUE IQ™ Instructions d’installation Instructions de sécurité importantes - Conservez ces instructions CAJA DE SEGURIDAD DIGITAL IQ™ Instrucciones de montaje Instrucciones importantes de seguridad - Guarde estas instrucciones UC 24, 30, 36, 48 RC 20, 24 PL 16, 20, 24 PC 16, 20, 24 MC 16, 20, 24 DC 16, 20, 24 AC 24 TABLE DES MATIÈRES CONTENIDO Outils nécessaires - 2 Pièces - 2 Notes - 3 Dimensions - 3 Installation encastrée existante - 4 Installation de surface existante - 5 Nouv
OUTILS NÉCESSAIRES HERRAMIENTAS NECESARIAS PIÈCES PIEZAS [211-1331] Boîte numérique verrouillée / Caja de seguridad digital Étagère de la boîte verrouillée / Estantería de la caja de seguridad [216-1192] Sac avec composants de montage / Bolsa con componentes de montaje* [216-1193] Kit de démarrage rapide / Bolsa con materiales básicos [203-1492] (4) #10 x 3/8" Vis / Tornillo IQ ™ DIGITAL LOCK BOX [203-1493] (4) #6 x 3/8" Vis / Tornillo IQ ™ DIGITAL LOCK BOX USER SET UP GUIDE [SS125] (4) #6 x
NOTES / NOTAS ATTENTION ! Pour réduire le risque de décharge électrique, coupez le courant avant de l’installer dans une armoire électrique. ¡ADVERTENCIA! Para reducir el riesgo de un choque eléctrico, desconecte la alimentación eléctrica antes de montar el accesorio en un armario con corriente. DIMENSIONS / DIMENSIONES 2-7/16" 62 (62mm) 2-7/16" 9-3/8" 238.3 9-3/8" (238mm) 9" 228.6 (229mm) 9" 5-1/4" 133.4 (133mm) 5-1/4" © 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A. 800.877.2376 www.
INSTALLATION ENCASTRÉE EXISTANTE MONTAJE EN HUECO EXISTENTE NOTA: Para aquellos armarios que cuenten con opciones eléctricas, apague el interruptor principal antes de iniciar el proceso de montaje. REMARQUE : Pour les armoires avec options électriques, coupez le disjoncteur avant de commencer. REMARQUE : Retirez la porte des armoires avant de commencer. NOTA: Extraiga las puertas de los armarios antes de iniciar el proceso. 1.
INSTALLATION DE SURFACE EXISTANTE MONTAJE SOBRE SUPERFICIE EXISTENTE REMARQUE : Pour les armoires avec options électriques, coupez le disjoncteur avant de commencer. NOTA: Para aquellos armarios que cuenten con opciones eléctricas, apague el interruptor principal antes de iniciar el proceso de montaje. REMARQUE : Retirez la porte des armoires avant de commencer. NOTA: Extraiga las puertas de los armarios antes de iniciar el proceso. 1.
NOUVELLE INSTALLATION : CABINETS PLM NUEVO MONTAJE: ARMARIOS PLM REMARQUE : Retirez la porte des armoires avant de commencer. NOTA: Retirez la porte des armoires avant de commencer. 1. Ouvrez le boîtier de la serrure numérique à l’aide de la clé fournie et retirez le sachet de matériel. 1. Con la llave suministrada, abra la caja de seguridad digital y extraiga la bolsa con los accesorios de montaje. 2.
NOUVELLE INSTALLATION : CABINETS PLM NOUVELLE INSTALLATION : ARMARIOS PLM 3. Insérez la tablette du boîtier de serrure dans l’armoire à la hauteur souhaitée en l’alignant sur les trous des goupilles de la tablette dans le boîtier de l’armoire. 3. Introduzca la estantería de la caja de seguridad en el armario a OD DOWXUD TXH GHVHH DOLQHiQGROD FRQ ORV RUL¿FLRV GH ORV WRSHV GH OD estantería que se encuentran en la caja del armario. 4.
NOUVELLE INSTALLATION : R3 / UPLIFT TECH NUEVO MONTAJE: R3 / UPLIFT TECH REMARQUE : Retirez la porte des armoires avant de commencer. NOTA: Extraiga las puertas de los armarios antes de iniciar el proceso. 1. Ouvrez le boîtier de la serrure numérique à l’aide de la clé fournie et retirez le sachet de matériel. 1. Con la llave suministrada, abra la caja de seguridad digital y extraiga la bolsa con los accesorios de montaje. 2.
NOUVELLE INSTALLATION : R3 / UPLIFT TECH NUEVO MONTAJE: R3 / UPLIFT TECH 3. Insérez la tablette du boîtier de la serrure dans l’armoire, juste au-dessus des blocs de montage. Appuyez doucement sur la tablette FRQWUH O¶DUULqUH GX ERvWLHU GX FRႇUHW SXLV IDLWHV OD JOLVVHU YHUV OH EDV jusqu’à ce qu’elle s’engage dans les blocs de montage. 3. Introduzca la estantería de la caja de seguridad en el armario y ligeramente por encima de las estructuras montaje.
ACHEVER L’INSTALLATION FINALIZACIÓN DEL MONTAJE 8QH IRLV TXH O¶pWDJqUH HVW ¿[pH LQVpUH] OH ERvWLHU YHUURXLOOp 6L votre étagère est plus large que le boîtier verrouillé, ajustez ce dernier à la position souhaitée, d’un côté à l’autre, à l’intérieur de l’armoire. 5. Una vez que la estantería esté bien instalada, introduzca la caja de seguridad.
NETTOYAGE LIMPIEZA 8WLOLVH] XQ FKLႇRQ KXPLGH SRXU OD QHWWR\HU /HV QHWWR\DQWV j base d’ammoniac ou de vinaigre risquent d’endommager les rétroviseurs. Utilice únicamente un trapo húmedo para limpiar el accesorio. Los productos de limpieza con amoníaco o vinagre pueden dañar los espejos. Une solution de 50/50 d’eau et d’alcool isopropylique est recommandée pour nettoyer le meuble de rétroviseurs. Para limpiar el espejos se recomienda una solución al 50/50 de agua y alcohol isopropílico. /RUV GX QHWWR\
UTILISATION ET ENTRETIEN USO Y MANTENIMIENTO Veuillez vous référer au guide de démarrage rapide du boîtier verrouillé numérique IQ [217-1382] pour les instructions d’installation et d’utilisation. Consulte la Guía de inicio rápido de la caja de seguridad digital IQ > @ SDUD REWHQHU LQIRUPDFLyQ VREUH OD FRQ¿JXUDFLyQ \ XVR de este accesorio. Veuillez vous munir du numéro de série et du code d’enregistrement de sécurité lorsque vous commandez des clés de remplacement.