Noise Canceling Headset with Bluetooth® Wireless Technology Instruction Manual i903 Please read this manual carefully before operating and save it for future reference. Have a question? Please visit http://www.i-Luv.
Noise-Canceling Headset w/ Bluetooth wireless technology -1- V10M10_IM_EN_12072006 www.i-Luv.
Noise-Canceling Headset w/ Bluetooth wireless technology V10M10_IM_EN_12072006 USER SAFETY GUIDE INSTRUCTIONS ON ENVIRONMENT PROTECTION Do not dispose of this product in the usual household garbage at the end of its life cycle; bring it to a collection point for the recycling of electrical and electronic appliances. This symbol on the product means the instructions for use or the packaging will inform about the methods of disposal. The materials are recyclable as mentioned in its marking.
Noise-Canceling Headset w/ Bluetooth wireless technology V10M10_IM_EN_12072006 USER SAFETY GUIDE FCC Notice (USA) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Refer to 47 CFR Sec. 15.19.
Noise-Canceling Headset w/ Bluetooth wireless technology V10M10_IM_EN_12072006 USER SAFETY GUIDE About Electromagnetic Interference (EMI) - Continued • • • If you use any personal medical device, such as a pacemaker, please consult the manufacture of your medical device to determine if it is adequately shielded from EMI. Your physician might assist you in obtaining this information. Please turn off this device if you are instructed to do so, especially on an airplane or in a hospital.
Noise-Canceling Headset w/ Bluetooth wireless technology -5- V10M10_IM_EN_12072006 www.i-Luv.
Noise-Canceling Headset w/ Bluetooth wireless technology V10M10_IM_EN_12072006 TABLE OF CONTENTS GETTING STARTED Introduction. …..………..………………………..……………………………………… 7 What’s Included…..…………………………..………………..………………………… 7 What is Bluetooth wireless technology? ................................................................
Noise-Canceling Headset w/ Bluetooth wireless technology V10M10_IM_EN_12072006 GETTING STARTED iLuvTM Noise-Canceling Headphones with Bluetooth® Wireless Technology The i903 frees you from the bondage of a wired environment using Bluetooth wireless technology. Not only that, but outside sounds that can be a distraction to pure music enjoyment or an annoyance during an important phone call virtually disappear, helping you focus on what you want to hear and not on what you have to hear.
Noise-Canceling Headset w/ Bluetooth wireless technology V10M10_IM_EN_12072006 GETTING STARTED What is Bluetooth wireless technology? Bluetooth wireless technology is a short-range wireless communication technology intended to replace the cables connecting electronic devices while maintaining the high level of security.
Noise-Canceling Headset w/ Bluetooth wireless technology V10M10_IM_EN_12072006 GETTING STARTED Charging the Headset and Audio Transmitter Before the first use of this headset, it is recommended to fully charge the headset and the included audio transmitter (dongle). To do so, follow the instructions below: 1. Locate the mini USB port (on the bottom of the right headphone, or top right on the dongle) before attaching USB cable. Mini USB port 2. Attach other end of cable to supplied USB power adapter. 3.
Noise-Canceling Headset w/ Bluetooth wireless technology V10M10_IM_EN_12072006 OPERATING INSTRUCTIONS LOCATION OF CONTROLS 1. Folding Head band 2. Multi-function button 3. Ear cushions for enhanced comfort and noise reduction 4. Built-in microphone to pick up your voice 5. USB jack to connect to power adapter or audio device 6. Volume control 7. LED indicator lights when Noise Cancellation is activated 8. Power on/off switch for Bluetooth and N/C 9. Play/Pause button - 10 - www.i-Luv.
Noise-Canceling Headset w/ Bluetooth wireless technology V10M10_IM_EN_12072006 OPERATING INSTRUCTIONS Turning On/Off the i903 or Wireless Audio Transmitter (dongle) To turn on the i903 and/or the included wireless audio transmitter (dongle), follow the instruction below: • Please find the on/off switch located on the left earpiece.
Noise-Canceling Headset w/ Bluetooth wireless technology V10M10_IM_EN_12072006 OPERATING INSTRUCTIONS Pairing i903 with the Included Wireless Audio Transmitter (Dongle) The i903 can be used with an audio device that is not designed to support Bluetooth wireless technology using the supplied wireless audio transmitter (dongle). In order to answer and place phone calls while using the dongle, it is important to pair the mobile phone first.
Noise-Canceling Headset w/ Bluetooth wireless technology V10M10_IM_EN_12072006 OPERATING INSTRUCTIONS Pairing i903 with your Mobile Phone or Audio Device Before using this headset, make sure that it is paired with a mobile phone and audio devices with Bluetooth wireless technology. To pair with such a device, follow the instructions below: 1. Please make sure the headset is at standby mode. If i903 is currently turned on then press the MultiFunction button for approximately five (5) seconds.
Noise-Canceling Headset w/ Bluetooth wireless technology V10M10_IM_EN_12072006 OPERATING INSTRUCTIONS Pairing i903 with your Mobile Phone or Audio Device – Continued 6. Enter the password: “0000.” The phone or device will display a confirmation message after a few seconds. Once the headset is correctly paired, the light will stop blinking red and blue alternately, and will blink blue only. 7. Repeat this procedure each time an additional phone or audio device needs to be paired with the i903. 8.
Noise-Canceling Headset w/ Bluetooth wireless technology V10M10_IM_EN_12072006 OPERATING INSTRUCTIONS Making a Call The i903 is designed to allow a user to place and answer calls while listening to music wirelessly with Bluetooth wireless technology. Your mobile phone must be paired with the i903 FIRST before pairing with other audio devices or the wireless audio transmitter. How calls are made, however, depends greatly on the phone to which the i903 is paired. 1.
Noise-Canceling Headset w/ Bluetooth wireless technology V10M10_IM_EN_12072006 OPERATING INSTRUCTIONS Answering a Call It is very simple to answer a call with the i903, whether listening to music or already talking on the phone. 1. An incoming phone call will be indicated by a ring after which the blue light on the i903 will blink. Press the Multi-function button once to answer the call. 2.
Noise-Canceling Headset w/ Bluetooth wireless technology V10M10_IM_EN_12072006 OPERATING INSTRUCTIONS Adjusting the Volume To adjust the volume on the i903 (for both phone calls and music), adjust the volume control buttons as shown below. Right/rear view Volume + Volume - 1. Press the Volume + button to increase the volume during a phone call or while listening to music. 2. Press the Volume – button to decrease the volume during a phone call or while listening to music.
Noise-Canceling Headset w/ Bluetooth wireless technology V10M10_IM_EN_12072006 OPERATING INSTRUCTIONS Listening to Music In order to listen to music on the i903, it must be paired with a device equipped with Bluetooth wireless technology. To pair with such a device, follow the instructions below: 1. Turn off the Bluetooth wireless communication if it is currently turned on by pressing the Multi-function button for approximately five (5) seconds. 2.
Noise-Canceling Headset w/ Bluetooth wireless technology V10M10_IM_EN_12072006 TROUBLESHOOTING GUIDE 1. ANR does not eliminate all outside sounds. o This is normal. No ANR headset on the market can completely eliminate outside noises. The noise reduction function only reduces the amount of noise and i903 is capable of -15dB noise reduction. 2. The headset does not work with my mobile phone. o Be certain that your mobile phone is equipped with Bluetooth wireless technology.
Noise-Canceling Headset w/ Bluetooth wireless technology V10M10_IM_EN_12072006 TROUBLESHOOTING GUIDE 7. 8. o Make sure both devices are in pairing mode to accept connections from each other. o Make sure the Bluetooth device you are using is Bluetooth Version 1.2 or higher for stable connectivity. (Some of the V1.1 devices might not be fully compatible.
Noise-Canceling Headset w/ Bluetooth wireless technology V10M10_IM_EN_12072006 SPECIFICATIONS Product Specifications • Speaker Driver: 30mm NdFeB speaker driver • Frequency Response: 20Hz – 20kHz (receiving) • Sensitivity: 105dB ± 3dB (ANR ON) • Active Noise Reduction Level: -15dB (Max) • Bluetooth Version: V1.2 • Bluetooth Profile: HSP, HFP, A2DP, AVRCP • Standby Mode: < 48hrs • ANR Stereo Function: < 33hrs (with BT function disabled) • Listening Mode: < 8hrs (@ max.
TEL: 516-626-7188 FAX: 516-626-7105 website: www.i-Luv.com iLuv is a trademark of jWIN Electronics Corp. Features and specifications are subject to change without prior notification. iPod is a trademark of Apple Computer, Inc. The Bluetooth word mark and logos are owned by Bluetooth SIG, Inc. and any use of such marks by jWIN Electronics Corp. is under license. Mobile phone not included in this package. © 2006 jWIN Electronics Corp. All rights reserved.
