Owner's Manual

FCC WARNING:
This equipment may generate
or use radio frequency energy. Changes
or modifications to this equipment may cause harmful interference unless
the modifications are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if an unauthorized
change
or modification is made.
NOTE:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15
of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference
in a residential installation, This equipment may cause
harmful interference to radio communications,
if it is not installed and
used in accordance with the instructions. However, there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, wihich can be determined by turning the equipment
off and on,
the user is encouraged to try to correct the interference by one
or more of
the following measures:
-- Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Consult the dealer or an experienced radio technician for help.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT
TO THE FOLLOWING TWO CONDITIONS:
(1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2)THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
NOTICE:
This Class B digital apparatus complies with Canadian ICES-003.
REMARQUE:
Get appareil numeique de
Ia classe B est conforme a Ia norme NMB-003
du Canada.
•English
Function and Operation
4
So ;/;Y~
6
3
2
7
•
\, ~~- •• ~~v /f •
1
1. Source Select
2. Seek+
3. Seek-
4.Up
Before Installation
A WARNING
If you connect the ignition wire (red) and
the illumination wire (orange) to the
negative ground point, you may cause a
short circuit, that in turn may start a fire.
Always connect those wires to the power
source running through the fuse box.
Lt
• This unit is designed for marine use.
• Mounting and wiring this product
requires skill and experience. For safety
reasons leave the mounting and wiring
work to professionals.
• Make sure to ground the unit to a
negative 12V DC power supply.
• Do not install the unit in a spot exposed
to direct sunlight
or excessive heat and/or
humidity.
• Do not use your own screws. Use only
screws provided. If
you use the wrong
screws you could damage the unit.
5
5.Down
6. Volume Up
7. Volume Down
8. Mute I Pause
•
If your vessel ignition does not have an
ACC protection, connect the ignition wire
to a power source that can be turned on
and
off with the key or other control
switch. If the receiver is left on for an
extended period
of time the battery may
die.
• If the fuse blows, first make sure the
wires aren't touching to cause a short
circuit. Then replace the old fuse with one
of the same rating.
• Insulate unconnected wires with vinyl
tape or other similar material. To prevent
a short circuit do not remove the caps on
the ends of the unconnected wires or the
terminals.
• After installing the unit, check to make
sure that electrical equipment such as the
signal lamps and gauges operate
normally.
JVC
RM-RK62M
REMOTE CONTROL UNIT
INSTRUCTION MANUAL
UNITE DE TELECOMMANDE
MODE D'EMPLOI
UNlOAD DE CONTROL REMOTO
MANUAL DE INSTRUCCIONES
JVC KENWOOD Corporation
Installation
1. Set the gasket to the place where the RM-RK62M is to be installed
and pierce with a drill bit for wiring harness and the installation.
2. Fix the RM-RK62M as shown in figure.
Connection
RM-RK62M
Remote Control
Output Remote Control Input
(Light Blue/Yellow) (Light Blue/Yellow)
Receiver
~- ===-r~"'"~-~00-, -- *"-------,
Ignition Key Switch L... _____ ...J
Illumination Wire
1
::::P"~\ (Orange) -
.. "I
Ground Wire (Black)
To a negative ground point
of the vessel
Fuse box
(Main Fuse)